Operating Instructions
4 Pages
Preview
Page 1
"%*/4536.&/54 ML317 EOG Pod Pod Series Description The ML317 EOG Pod is a signal conditioner designed to record horizontal and vertical eye position and movement. The device features a manual DC offset and is supplied with three shielded lead wires with snap-on connectors.
System Compatibility The EOG Pod connects to any PowerLab hardware units with Pod ports (8-pin DIN inputs). PowerLab and MacLab (except 4s, 8s and 16s) units without Pod ports require the ML305 Pod Expander. The EOG Pod is supported by the following versions of Chart and Scope software: WINDOWS
MACINTOSH
• Chart v3.4.8 or later • Scope v3.6.3 or later
• Chart v3.6.3 or later • Scope v3.6.3 or later
Note: Earlier software versions do not support Pods.
Accessories The Pod is supplied with three snap-on connector shielded lead wires which snap connect to conductive (Ag/AgCl) adhesive electrodes (MLA1010).
Applications The EOG Pod is used to measure and display eye movement and position. In the human the EOG Pod can be used in the measurement of saccadic and pursuit eye movements. It is ideal for use in undergraduate teaching laboratories.
Operating Instructions Connect the 8-pin DIN cable from the EOG Pod to a PowerLab Pod port or a Pod port of a Pod Expander connected to the PowerLab. Do not connect other devices such as Front-ends or Instruments to the corresponding BNC connector on the channel used by the Pod. Pods can be connected to the PowerLab unit while Chart or Scope software is running, but not when recording data. Once detected, the functions of the EOG Pod are combined with those of the PowerLab and software, replacing the Input Amplifier dialog with the EOG Pod (Figure 1). Figure 1
Click this button to open the “Units Conversion” dialog window.
Theory of Operation The EOG Pod is a DC coupled biopotential amplifier with a fixed low-pass filter (500 Hz) to remove high frequencies. On the front of the Pod, an offset knob is provided to remove DC drift. The offset control provides ±15 mV of offset range (at input) for all range selections. The EOG Pod utilizes the steady corneal-retinal potential in the detection of eye movement and position. This steady dipole may be used to measure eye position by placing surface electrodes to the left and right of the eyes (Figure 2). When the gaze is straight ahead, the steady dipole is symmetrically placed between the two electrodes, and the EOG output is approximately zero. When the gaze is shifted to the left, the positive cornea comes closer to the left electrode, which becomes more positive. There is an almost linear relationship between horizontal angle of gaze and EOG output (approximately ±30º of arc). Electrodes can also be placed above and below the eye to record vertical eye movements and using two EOG Pods, simultaneous vertical and horizontal eye movements can be measured (Figure 3).
Stacking and Unstacking Pods Pods stack by clicking into place on top of each other. To separate stacked Pods, push the top Pod towards the back and then pull them apart from the back. See picture on right.
Typical Data Figure 2
Electrodes placed on the left and right side of the eyes. The reference electrode was placed on the back of the neck. The screen capture above shows a recording of horizontal eye movements.
Figure 3
Electrodes were placed on the left and right side of the eyes, as well as above and below the right eye. The screen capture above shows horizontal (Channel 1) and vertical (Channel 2) eye movements using two EOG Pods.
Back Panel Figure 4 Active Pins Ground Pins
Cable to PowerLab
REF GND
WARRANTY: ADInstruments PowerLab Systems, Front-end and Pod Signal Conditioners are warranted against defects in materials and workmanship for a period of 3 years from the date of purchase. Third party products are covered by the manufacturer’s warranty. Warranties are void if the product has been damaged due to negligence. Consumables and electrodes are not covered by a warranty. All questions regarding service and warranty should be directed to your nearest ADInstruments representative or one of the offices listed below.
Caution Read “Statement of Intended Use” on our website or in “Getting Started with PowerLab” before use. Specifications Amplification range: Pod gain: Gain error: Frequency response: Low pass filter: Temperature drift: CMRR: IMRR: Input impedance: Front panel control: Input bias (maximum): Input connector: Cable length: Weight:
±2 mV, ±1 mV, ±500 μV, ±200 μV, ±100 μV ×1000 ±5% untrimmed, ±0.1% when calibrated DC to 500 Hz 500 (fixed) 2nd order Butterworth ±3 mV/°C >80 dB >110 dB <100 MΩ offset knob for initial zeroing of device ±10 nA @ 25 °C 3 shielded lead wire connectors 1.5 m 200 ga
All specifications were tested at the time of printing and are subject to change.
Ordering Information ML317 EOG Pod For use with: MLA1010 Disposable ECG Electrodes Supplied with MLA2503 Shielded Lead Wires (set of three).
ML317-DC-06A
ADINSTRUMENTS.com
ISO 9001:2000 Certified Quality Management System
North America
United Kingdom
Tel: +1 888 965 6040 Fax: +1 866 965 9293 info@adinstruments.com
Tel: +44 1865 891 623 Tel: +49 6226 970105 Tel: +86 21 5830 5639 Tel: +60 3 8023 6305 Fax: +44 1865 890 800 Fax: +49 6226 970106 Fax: +86 21 5830 5640 Fax: +60 3 8023 6307 info.uk@adinstruments.com info.de@adinstruments.com info.cn@adinstruments.com info.sea@adinstruments.com
Germany
Japan
Australia
Indian Subcontinent
Asia
South America
South East Asia
International
Tel: +81 52 932 6462 Tel: +61 2 8818 3400 Tel: +91 11 2693 3930 Tel: +56 2 356 6749 Tel: +61 2 8818 3400 Fax: +81 52 932 6755 Fax: +61 2 8818 3499 Fax: +91 11 2693 3929 Fax: +56 2 356 6786 Fax: +61 2 8818 3499 info.jp@adinstruments.com info.au@adinstruments.com info.in@adinstruments.com info.cl@adinstruments.com info.au@adinstruments.com