ARJO Huntleigh Healthcare
Contoura 980B and 1080 Scales Instructions for Use
Instructions for Use
2 Pages
Preview
Page 1
CONTOURA® 980B & 1080 WITH WEIGHING INSTRUCTIONS FOR USE Transport • Whenever the bed is moved over any significant distance, it must be put into transport mode, otherwise the load cells may be damaged. To put into transport mode, turn the screws on the four corners of the bed base in a clockwise direction until fully down and finger-tight. It is not necessary to put the bed into transport mode for moving short distances round a hospital. • When the bed is stationary and weighing is to be re-commenced, turn the screws in an anti-clockwise direction until fully up and finger-tight, and switch the mains power on. The system can then be set to zero, and weighing can be recommenced. • The bed must be installed on a flat, level floor for weighing. Position of Patient for Weighing • The bed can be in any position for weighing. However, it must be freestanding – i.e. not touching any walls, lockers, curtains etc. • The bed does not have to be in the same position for every weight reading for any given patient – e.g. the patient can be weighed in the morning completely flat, and in the evening in a chair position. MRF-139
• The patient can be in any position on the bed for weighing, as long as their whole body is on top of the mattress – i.e. no arms, legs etc. dangling over the side. The patient can therefore be flat on their back, on their side etc. However, we recommend that they are positioned as centrally as possible to ensure maximum accuracy. • During weighing, there must be no drainage bags, bottles etc. leading from the patient and resting on the floor. Any such items should be either placed on top of the mattress or be hanging from the side of the bed frame. Accuracy The weighing system on Contoura® 980B is accurate to ± 200 g. Contoura® 980B will weigh up to a maximum of 250 kg (39 stones / 550 lbs.). The display shows kg only. The weighing system on Contoura® 1080 is accurate to ± 500 g. Contoura® 1080 will weigh up to 500 kg (78 stones / 1100 lbs.). The display shows kg only.
OPERATING INSTRUCTIONS FOR WEIGH SCALE ON CONTOURA BED
A: Resets top display to gross weight Resets bottom display to zero B: ‘Enter’ button for bottom scale C ‘Enter’ button for top scale D: Weight change display E: Patient weight display
F: Green ‘ready’ light G: Keypad to enter manual weight for a patient K: Zero button L: Auto compensation button M: Hides all readings to both displays
WHEN MOVING BED REMEMBER TO USE LOCKOUT SCREWS TO STOP DAMAGE TO WEIGHSCALE How to set up bed ready for patient 1. Undo all four lockout screws that are situated under frame on each corner. 2. Add mattress and linen to be used. 3. Switch on power and wait for display to read ‘COLD’ and then disappear. 4. Press button ‘C’ and then button ‘K’.
How to add/remove eqpt./linen with patient on bed 1. Press either button ‘B’ or ‘C’. 2. Press button ‘L’, the adjacent display will read ‘0’. 3. Press either button ‘B’ or ‘C’ again. 4. Top display will now read ‘AUTO-COMP’ and bottom display will be blank.
5. Wait for green light ‘F’, then press button ‘C’ again.
5. Wait for green light to display.
6. Display should read ‘0’.
6. Add/remove eqpt/ linen as required.
7. Repeat tasks (4) to (6) using button ‘B’.
7. Press following buttons in this sequence – ‘C’ or ‘B’, then button ‘L’ and finally button ‘B’ or ‘C’ again.
8. Bottom scale should also read ‘0’. 9. Put patient on bed.
8. Both displays will show patient’s continuous place weight again. MRF-139