Model AR-6480 DualWave Arthroscopy Pump Quick Reference Guide Rev 0 Aug 2019

ACCESSORIES

ARTHROSCOPY PUMP ACCESSORIES Autoclavable Remote

Lavage

Pressure Down

Shaver Suction Toggle

2

Foot Control

Rinse

Pressure Up

Run/Stop

Lavage: Timed increase of pressure for improved control of bleeding. Rinse: Timed increase of flow for improved control of debris removal. (Only available when using DualWave outflow) Shaver Suction Toggle: Allows switching between 4 preset shaver suction levels. (Only available when using DualWave outflow)

INFLOW

INFLOW TUBING SET-UP

1 Remove orange clip

2

3

4

Insert connector into Open inflow door pump pressure coupler

Insert green tubing hub

5 Wrap tubing around rollers

Inflow door Rollers

6

7

Insert clear tubing hub Close inflow door

Green tubing hub

Pump pressure coupler

8 Spike saline bags

Clear tubing hub

3

INFLOW

INFLOW ONLY USER INTERFACE Inflow Only

Stopped

Fluid Used

Set Pressure

Boost Control

Pressure Down

Pressure Up

Run/Stop

Menu

Running Pressure Reading Flow Rate

Run Time (Resets after power down) Run/Stop

Lavage 4

OUTFLOW

OUTFLOW TUBING SET-UP Shaver

Cut as needed

Outflow Boot

Waste

Luer Lock

1 Connect to shaver suction

3 Open outflow door

2 Connect to independent cannula

4

Pass off Cassette and Red Waste Tubing Cannula

5

*Install outflow cassette Close outflow door

6 Outflow display

7 Connect red waste tubing to waste system

*For easy set-up, move the rollers so that two wheels are flush. Extend the boot of the outflow cassette over the two wheels at the same time. With one hand, hold the boot in place; and, with the second hand, pull down on all three tubes, pushing the cassette in place. The cassette will be held in place by the edges of the outflow bezel.

5

INFLOW/OUTFLOW

INFLOW/OUTFLOW USER INTERFACE Inflow/Outflow

Stopped

Fluid Used

Cannula Suction Control

Shaver Suction Control

Set Pressure Pressure Down

Pressure Up

Run/Stop

Menu

Running Flow Rate

Pressure Reading

Run Time (Resets after power down) Run/Stop

Lavage 6

Rinse

SHAVER DETECTION

SYNERGY SHAVER DETECTION AND HEADS UP DISPLAY

1

2

Connect red cable that comes with DualWave to the rear of Synergy Resection Console

™

Power on Synergy Resection Console 3 2

3 Power on DualWave

4 *Connect to Synergy Imaging for heads up display cable

*For Synergy heads up display use AR-3200-1040 accessory cable kit to connect DualWave to camera console. (Only 1 cable is needed to connect the DualWave to the camera console.) Prior to using this system, see IFU 950-0052-00 for more detail.

7

SHAVER DETECTION

UNIVERSAL SHAVER DETECTION

1 Shaver detect cord

2 Plug into DualWave™

6 4 3 Plug into Shaver Console

5 Plug in handpiece 8

4 Power on Shaver Console

6 *Power on DualWave

*Shaver console must be fully powered up before DualWave is powered on

TROUBLESHOOTING

TROUBLESHOOTING PROBLEM

SOLUTION

** Critical Failure **

Return to Arthrex® for repair.

** Door Open **

1. Roller housing is not secured – ensure the locking lever is properly secured. 2. If the failure persists, return to Arthrex for repair.

** Overpressure **

1. Increase or open the outflow. 2. Manipulate the joint to a stress-free position. 3. If the failure persists, return to Arthrex for repair.

** Pressure Fault **

1. Ensure adequate fluid supply. 2. Decrease the outflow. 3. Check the tubing for damage or pinches, kinks, or blockages. 4. Check the tubing for the proper connections. 5. Replace the tubing. 6. If the failure persists, return to Arthrex for repair.

** Tubing Out **

1. If the tubing sensor indicator’s LED is red, the tubing is not properly connected. 2. Ensure the tubing sensor coupler is open, not seated. 3. Ensure that the tubing pressure line connector is seated completely. 4. Change the tubing. 5. If the failure persists, return to Arthrex for repair.

Console fails Self Diagnostic Test

1. Ensure no tubing is connected to the pump during the power on sequence. 2. If the failure persists, return to Arthrex for repair.

Console will not power up

1. Check the AC mains power cord. 2. Try an alternate power outlet. 3. Check the AC mains fuses. 4. If the failure persists, return to Arthrex for repair.

PROBLEM

SOLUTION

Does not pump when activated

1. Check for error messages. 2. Open all tubing clamps and shut-off valves. 3. Ensure the actual pressure is below the target pressure. 4. Check the tubing for pinches, kinks, or blockages. 5. If the failure persists, return to Arthrex for repair.

Inadequate distention, liquid bloody or cloudy

1. Increase the pressure. 2. Activate Lavage mode. 3. Reduce the outflow. 4. Use high-flow cannulas. 5. If the failure persists, return to Arthrex for repair.

No (or inadequate) flow

No Shaver Detect

1. Check for error messages. 2. Check that all tubing clamps are open. 3. Check the settings for flow and pressure. 4. Check the tubing for pinches, kinks, or blockages. 5. Check that the tubing seats correctly over the rollers. 6. Verify use of high-flow cannulas. 7. If the failure persists, return to Arthrex for repair. Synergy Shaver Detection 1. Verify DualWave™ software is at least 1.8 2. Verify Synergy Resection Console is at least 2.3. 3. Ensure the Synergy cable is connected. 4. Press stop and then run on DualWave while the Synergy Resection Console is on. 5. Replace cable. 6. If the failure persists, return to Arthrex for repair. Universal Shaver Detection 1. Ensure the universal shaver cable is connected. 2. Turn DualWave on and off while the shaver system is powered on. 3. Adjust the DELAY and/or THRESHOLD settings. 4. Isolate the power source. 5. If the failure persists, return to Arthrex for repair.

9

This description of technique is provided as an educational tool and clinical aid to assist properly licensed medical professionals in the usage of specific Arthrex products. As part of this professional usage, the medical professional must use their professional judgment in making any final determinations in product usage and technique. In doing so, the medical professional should rely on their own training and experience and should conduct a thorough review of pertinent medical literature and the product’s Directions For Use.

http://www.arthrex.com/imaging-resection/fluid-management

View U.S. patent information at www.arthrex.com/corporate/virtual-patent-marking 2019, Arthrex Inc. All rights reserved. DFU-0244-2 rev. 0 08/2019

©

DFU-0244-2 r0

10