Amputation saws FH300R, FH305R, FH306R, FH313R, FH320R, FH325R

en ®

Aesculap Amputation saws FH300R, FH305R, FH306R, FH313R, FH320R, FH325R

Notes on surgical procedures It is the user's responsibility to ensure that the surgical procedure is performed correctly. Appropriate clinical training as well as a theoretical and practical proficiency of all the required operating techniques, including the use of this product, are prerequisites for the successful use of this product. The user is required to obtain information from the manufacturer if there is an unclear preoperative situation regarding the use of the product.

Legend

2.3.2

1 2 3 4

The product is delivered in an unsterile condition. ► Clean the new product after removing its transport packaging and prior to its initial sterilization.

Straining screw Saw blade holder Saw blade Stabilization bracket

2.4

Sterility

Application

Note General risk factors associated with surgical procedures are not described in these instructions for use.

WARNING Risk of injury and/or malfunction! ► Prior to each use, inspect the product for loose, bent, broken, cracked, worn, or fractured components. ► Always carry out a function test prior to each use of the product.

1.1

3.

Validated reprocessing procedure

3.1

General safety instructions

1.

About this document

Scope

These instructions for use apply for the following products: Art. no.

Designation

FH300R, FH305R, FH306R, FH313R, FH320R, FH325R

Amputation saws

FH301C, FH302C, FH307C, FH308C, FH310C, FH312C, FH314C, FH315C, FH316C, FH326R

Saw blades

► For article-specific instructions for use as well as information on material compatibility and lifetime see B. Braun

eIFU at eifu.bbraun.com

1.2

Safety messages

Safety messages make clear the dangers to patient, user and/or product that could arise during the use of the product. Safety messages are labeled as follows: WARNING Indicates a possible threat of danger. If not avoided, minor or moderate injury may result. CAUTION Indicates a possible threat of material damage. If not avoided, the product may be damaged.

2.

Clinical use

2.1

Product description

2.1.1

Available sizes

Art. no.

Designation

FH300R

CHARRIERE amputation saw with 2 blades:

■ FH301C ■ FH302C

■ Saw blade 12 mm for FH300R ■ Saw blade 18 mm for FH300R

FH305R

RUST amputation saw 390 mm with 4 blades:

■ FH307C ■ FH308C ■ FH310C ■ FH312C

■ Saw blade 6 mm for FH305R ■ Saw blade 8 mm for FH305R ■ Saw blade 12 mm for FH305R ■ Saw blade 20 mm for FH305R (accessory, not included in FH305R)

FH306R

Bracket only for FH305R

FH313R

BIER amputation saws, blade 270 mm with 3 blades:

■ FH314C ■ FH315C ■ FH316C

■ Saw blade 4 mm for FH313R ■ Saw blade 6 mm for FH313R ■ Saw blade 8 mm for FH313R

FH320R

CHARRIERE amputation saw 270 mm, blade 180 mm

FH325R

SATTERLEE amputation saw 290 mm, blade 200 mm

■ FH326R

■ Saw blade 200 mm for FH325R

Note Adhere to national statutory regulations, national and international standards and directives, and local, clinical hygiene instructions for sterile processing. Note For patients with Creutzfeldt-Jakob disease (CJD), suspected CJD or possible variants of CJD, observe the relevant national regulations concerning the reprocessing of products. Note Mechanical reprocessing should be favored over manual cleaning as it gives better and more reliable results. Note Successful processing of this medical device can only be ensured if the processing method is first validated. The operator/sterile processing technician is responsible for this. Note If there is no final sterilization, then a virucidal disinfectant must be used. Note For up-to-date information about reprocessing and material compatibility, see B. Braun eIFU at eifu.bbraun.com The validated steam sterilization procedure was carried out in the Aesculap sterile container system.

3.2

General information

Dried or affixed surgical residues can make cleaning more difficult or ineffective and lead to corrosion. Therefore the time interval between application and processing should not exceed 6 h; also, neither fixating pre-cleaning temperatures >45 °C nor fixating disinfecting agents (active ingredient: aldehydes/alcohols) should be used. Excessive measures of neutralizing agents or basic cleaners may result in a chemical attack and/or to fading and the laser marking becoming unreadable visually or by machine for stainless steel. Residues containing chlorine or chlorides e.g. in surgical residues, medicines, saline solutions and in the service water used for cleaning, disinfection and sterilization will cause corrosion damage (pitting, stress corrosion) and result in the destruction of stainless steel products. These must be removed by rinsing thoroughly with demineralized water and then drying. Additional drying, if necessary. Only process chemicals that have been tested and approved (e.g. VAH or FDA approval or CE mark) and which are compatible with the product’s materials according to the chemical manufacturers’ recommendations may be used for processing the product. All the chemical manufacturer's application specifications must be strictly observed. Failure to do so can result in the following problems: ■ Optical changes of materials, e.g. fading or discoloration of titanium or aluminum. For aluminum, the application/process solution only needs to be of pH >8 to cause visible surface changes. ■ Material damage such as corrosion, cracks, fracturing, premature aging or swelling. ► Do not use metal cleaning brushes or other abrasives that would damage the product surfaces and could cause corrosion. ► Further detailed advice on hygienically safe and material-/value-preserving reprocessing can be found at www.ak-i.org, link to "AKI-Brochures", "Red brochure".

3.3

Reusable products

Influences of the reprocessing which lead to damage to the product are not known. A careful visual and functional inspection before the next use is the best opportunity to recognize a product that is no longer functional, see Inspection.

3.4

Preparations at the place of use

► If applicable, rinse non-visible surfaces preferably with deionized water, with a disposable syringe for example. ► Remove any visible surgical residues to the extent possible with a damp, lint-free cloth. ► Transport the dry product in a sealed waste container for cleaning and disinfection within 6 hours.

2.2

Areas of use and limitations of use

3.5

2.2.1

Intended use

► Disassemble the product prior to cleaning, see Disassembly.

Preparing for cleaning

Amputation saws are used for separating bone or bone elements.

3.6

Disassembly

2.2.2

3.6.1

FH300R/FH305R/FH306R

Indications

Note The manufacturer is not responsible for any use of the product against the specified indications and/or the described applications. For indications, see Intended use.

2.2.3

Contraindications

No known contraindications.

2.3

Safety information

2.3.1

Clinical user

General safety information To prevent damage caused by improper setup or operation, and to not compromise the manufacturer warranty and liability: ► Use the product only according to these instructions for use. ► Follow the safety and maintenance instructions. ► Ensure that the product and its accessories are operated and used only by persons with the requisite training, knowledge and experience. ► Store any new or unused products in a dry, clean, and safe place. ► Prior to use, check that the product is in good working order. ► Keep the instructions for use accessible for the user. Note The user is obligated to report all severe events in connection with the product to the manufacturer and the responsible authorities of the state in which the user is located.

► Unscrew straining screw 1 counterclockwise. ► Remove saw blade 3 from saw blade holder 2.

3.6.2

FH313R

► Press saw frame together and remove saw blade from saw blade holder.

3.6.3

FH320R/FH325R

► Fold stabilization bracket 4 away from saw blade 3.

3.7

Cleaning/Disinfection

3.7.1

Product-specific safety information on the reprocessing method

Damage to or destruction of the product due to inappropriate cleaning/disinfecting agents and/or excessive temperatures! ► Following the manufacturer's instructions, use cleaning and disinfecting agents that are approved for stainless steel. ► Observe specifications regarding concentration, temperature and exposure time. ► Do not exceed the maximum allowable disinfection temperature of 95 °C. ► Use suitable cleaning/disinfecting agents if the product is disposed of in a wet condition. To prevent foaming and

degradation of the efficacy of the process chemicals: prior to mechanical cleaning and disinfection, rinse the product thoroughly with running water

3.7.2

Validated cleaning and disinfection procedure

3.9.1

Mechanical alkaline cleaning and thermal disinfecting

Machine type: single-chamber cleaning/disinfecting machine without ultrasound Validated procedure

Specific requirements

Reference

Manual cleaning with immersion disinfection

► Use a suitable cleaning brush. ► Use a disposable syringe 20 ml. ► When cleaning instruments

Chapter Manual cleaning/disinfection and subsection:

Phase

■ Chapter Manual cleaning with

with movable hinges, ensure that these are in an open position and, if applicable, move the hinge while cleaning. ► Drying phase: Use a lint-free cloth or medical compressed air

Step

D [°C/°F]

t [min]

Water quality

Chemical/Note

I

Prerinse

<25/77

3

D–W

-

II

Cleaning

55/131

10

FD-W

■ Concentrate, alkaline:

immersion disinfection

– pH ~ 13 – <5 % anionic surfactant

■ working solution 0.5% – pH = 11*

Mechanical alkaline cleaning and thermal disinfection

3.8

► Manually pre-clean the prod-

uct (with a cleaning brush) if there are residues of bone, tissue or ancillary materials (such as plaster or bone cement). ► Place the product on a tray that is suitable for cleaning (avoid rinsing blind spots). ► Place the product on the tray with all product links and joints open.

Chapter Mechanical cleaning/disinfection and subsection:

■ Chapter Mechanical alkaline cleaning and thermal disinfecting

III

Intermediate rinse

>10/50

1

FD-W

-

IV

Thermal disinfecting

90/194

5

FD-W

-

V

Drying

-

-

-

According to the program for cleaning and disinfection device

DW: FD–W:

Drinking water Fully desalinated water (demineralized, low microbiological contamination: drinking water quality at least) *Recommended: BBraun Helimatic Cleaner alcaline

Manual cleaning/disinfection

► Prior to manual disinfecting, allow water to drip off for a sufficient length of time to prevent dilution of the dis-

infecting solution. ► After manual cleaning/disinfection, check visible surfaces visually for residues. ► Repeat the cleaning/disinfection process if necessary.

3.8.1

Manual cleaning with immersion disinfection

Phase

Step

T [°C/°F]

t [min]

Conc. [%]

Water quality

Chemical

I

Disinfecting cleaning

RT (cold)

>15

2

D–W

Aldehyde-free, phenol-free, and QUAT-free concentrate, pH ~ 9*

II

Intermediate rinse

RT (cold)

1

-

D–W

-

III

Disinfection

RT (cold)

5

2

D–W

Aldehyde-free, phenol-free, and QUAT-free concentrate, pH ~ 9*

IV

Final rinse

RT (cold)

1

-

FD-W

-

V

Drying

RT

-

-

-

-

► Check visible surfaces for residues after mechanical cleaning/disinfecting.

3.10 Inspection ► Allow the product to cool down to room temperature. ► Dry the product if it is wet or damp.

3.10.1 Visual inspection ► Ensure that all soiling has been removed. In particular, pay attention to mating surfaces, hinges, shafts, recessed

areas, drill grooves and the sides of the teeth on rasps. ► If the product is dirty: repeat the cleaning and disinfection process. ► Check the product for damage, e.g. insulation or corroded, loose, bent, broken, cracked, worn or severely

scratched and fractured components. ► Check the product for missing or faded labels. ► Check the products with long, slim shapes (in particular rotating instruments) for deformities. ► Check the product for damage to the spiral element. ► Check the cutting edges for continuity, sharpness, nicks and other damage. ► Check the surfaces for rough spots. ► Check the product for burrs that could damage tissue or surgical gloves. ► Check the product for loose or missing parts. ► Immediately put aside damaged or inoperative products and send them to Aesculap Technical Service, see Tech-

nical service.

3.10.2 Functional test D–W: Drinking water FD–W: Fully desalinated water (demineralized, microbiological, at least of drinking water quality) RT: Room temperature *Recommended: BBraun Stabimed fresh ► Note the information on appropriate cleaning brushes and disposable syringes, see Validated cleaning and dis-

infection procedure.

► Assemble disassembled products, see Assembly. ► Check that the product functions correctly. ► Check that all moving parts are working property (e.g. hinges, locks/latches, sliding parts etc.). ► Check for compatibility with associated products. ► Immediately put aside inoperative products and send them to Aesculap Technical Service, see Technical service.

3.11 Assembly

Phase I ► Fully immerse the product in the cleaning/disinfectant for at least 15 min. Ensure that all accessible surfaces are moistened. ► Clean the product with a suitable cleaning brush in the solution until all discernible residues have been removed from the surface. ► If applicable, brush through non-visible surfaces with an appropriate cleaning brush for at least 1 min. ► Mobilize non-rigid components, such as set screws, links, etc. during cleaning. ► Thoroughly rinse through these components with the cleaning disinfectant solution (at least five times), using a disposable syringe.

3.11.1 FH300R/FH305R/FH306R

Phase II ► Rinse/flush the product thoroughly (all accessible surfaces) under running water. ► Mobilize non-rigid components, such as set screws, joints, etc. during rinsing. ► Drain any remaining water fully.

3.12 Packaging

Phase III ► Fully immerse the product in the disinfectant solution. ► Mobilize non-rigid components, such as set screws, joints, etc. during rinsing. ► Rinse lumens at least 5 times at the beginning of the exposure time using an appropriate disposable syringe. Ensure that all accessible surfaces are moistened.

► Insert saw blade 3 into saw blade holders 2. ► Tighten straining screw 1 clockwise, thereby tensioning saw blade.

3.11.2 FH313R ► Insert saw blade into front saw blade holder. ► Press together saw frame and insert saw blade into rear saw blade holder.

3.11.3 FH320R/FH325R ► Attach stabilization bracket 4 onto saw blade 3.

► Place the product in its holder or on a suitable tray. Ensure that sharp edges are covered. ► Package trays appropriately for the sterilization process (e.g. in Aesculap sterile containers). ► Ensure that the packaging provides sufficient protection against contamination of the product during storage.

3.13 Steam sterilization ► Check to ensure that the sterilizing agent will come into contact with all external and internal surfaces (e.g., by

opening any valves and faucets). ► Validated sterilization process

Phase IV ► Rinse/flush the product thoroughly (all accessible surfaces). ► Mobilize non-rigid components, such as set screws, joints, etc. during final rinse. ► Rinse lumens with an appropriate disposable syringe at least five times. ► Drain any remaining water fully.

– Steam sterilization using fractional vacuum process – Steam sterilizer according to DIN EN 285 and validated according to DIN EN ISO 17665 – Sterilization using fractionated vacuum process at 134 °C/holding time 5 min ► If several devices are sterilized at the same time in the same steam sterilizer: Ensure that the maximum permitted load according to the manufacturers’ specifications is not exceeded.

Phase V ► Dry the product in the drying phase with suitable equipment (e.g. cloth, compressed air), see Validated cleaning and disinfection procedure.

3.14 Storage

3.9

4.

Maintenance and service

4.1

Technical service

Mechanical cleaning/disinfection

Note The cleaning and disinfection device must be of tested and approved effectiveness (e.g. FDA approval or CE mark according to DIN EN ISO 15883). Note The cleaning and disinfection device used for processing must be serviced and checked at regular intervals.

► Store sterile products in germ-proof packaging, protected from dust, in a dry, dark, temperature-controlled area.

CAUTION Modifications carried out on medical technical equipment may result in loss of guarantee/warranty rights and forfeiture of applicable licenses. ► Do not modify the product. ► For service and repairs, please contact your national B. Braun/Aesculap agency. Service addresses Aesculap Technischer Service Am Aesculap-Platz 78532 Tuttlingen / Germany Phone: +49 7461 95-1601 Fax: +49 7461 16-2887 E-Mail: [email protected] Other service addresses can be obtained from the address indicated above.

4.2

Spare parts

Art. no.

Designation

FH301C

Saw blade 12 mm for FH300R

FH302C

Saw blade 18 mm for FH300R

FH307C

Saw blade 6 mm for FH305R

FH308C

Saw blade 8 mm for FH305R

FH310C

Saw blade 12 mm for FH305R

FH312C

Saw blade 20 mm for FH305R

FH314C

Saw blade 4 mm for FH313R

FH315C

Saw blade 6 mm for FH313R

FH316C

Saw blade 8 mm for FH313R

FH326R

Saw blade 200 mm for FH325R

5.

Disposal

WARNING Risk of infection due to contaminated products! ► Adhere to national regulations when disposing of or recycling the product, its components and its packaging. WARNING Risk of injury due to sharp-edged and/or pointed products! ► When disposing of or recycling the product, ensure that the packaging prevents injury by the product. Note The user institution is obliged to reprocess the product before its disposal, see Validated reprocessing procedure. TA014650

2020-07

V6

Change No. 62511