Recycling Passport Endoscopy trolley PV800, PV810

GB

DECLARATION

We, Aesculap AG, confirm that the products Endoscopy trolley narrow PV800 Endoskopy trolley wide PV810 comply with the following guidelines: Waste electrical and electronic equipment (WEEE) 2002/96/EC (vom 27.01.2003) Category 8 product according to Annex IA Electrical and Electronic Equipment Act - ElektroG as well as the statutory requirements of the EEA member states

September, 2018 Aesculap AG, Am Aesculap-Platz, 78532 Tuttlingen / Germany

3

GB

ITEM

INFORMATION FOR RE-USE AND TREATMENT PV800 / PV810

MATERIAL

WEIGHT PV800/ PV810*

INFORMATION

-

-

Re-use Scrap 010

Earth conductor

0.66 kg

External electrical line

020

Cable harness

0.745 kg

External electrical line

030

Isolating transformer with insulation monitor (PV828)

20 kg

Remove: PCB > 10 cm²; See the manufacturer's instructions for use

Recycling Metal 040

Aluminium

12.81 kg/ 14.98 kg

Spars, drawer front panel, marking disc for POAG pins, right and left chassis feet

050

Stainless steel 1.4301

0.931 kg

POAG distribution plate, lock bracket

060

Spring steel

0.006 kg

All spring rings and spring washers (the items shown are only examples)

070

Nickel-plated brass

0.54 kg/ 0.66 kg

All spring rings and spring washers

080

Steel DC01 powder coated

0.487 kg

Disconnection prevention for underframe pan

090

Steel DC04 powder coated

31.90 kg 47.9 kg

Rear wall covers, cable duct covers, rear wall inner part, shelves, drawer side parts, base plate

100

Steel St37 powder coated

5.1 kg

Underframe pan for isolating transformer

100

Steel St37 powder coated

0.487 kg

Disconnection prevention for underframe pan

110

Galvanized steel

1.87 kg/ 2.36 kg

All screws, washers and nuts (as item numbers shown only as examples), drawer guides

120

Nickel plated steel

0.188 kg

Rear wall locks, drawer lock

130

Nickel plated steel / burnished, spring steel

0.632 kg

Spring nut slot (the item mumbers shown are only examples)

Plastic

4

140

ABS

0.96 kg

Profile caps on the rails, corner sliding handles on shelf, corner angle on shelves, corner angle on drawer front, drawer handles, slot covers in spars

150

Neoprene rubber

0.03 kg

Grommets on the inside left and right side of the rear wall

160

Nylon

0.081 kg

Self-adhesive cable holder (not shown as item number), with strain relief

170

Polystyrene

1.075 kg

Drawer body, label insert cover for drawer handle

180

PP

0.014 kg 0.016 kg

Cable tie (not shown as an item number)

190

PVC

1.276 kg

Feedthrough at the rear inside wall part between rear wall and shelves, cover profiles of spars and ducts of cable channel in spars

200

Polyolefins

0.016 kg

Heat shrink tubing at power switch assembly (not shown as an item number)

Composite materials 210

Copper, steel, thermoplastics, polyolefins

0.041 kg

Power switch

210

Copper, steel, thermoplastics, polyolefins

0.255 kg

Power distributor PV829/PV829U

220

Anodised aluminum, PA6-GF30, copper, steel

0.42 kg

Electrical socket strips

230

Polyamide, polyurethane, galvanized steel, soft polyethylene

3.83 kg

Double swivel castors

Total

63.6 kg 82.4 kg

Empty weight, without mains input

77.9 kg 96.7 kg

With power distributor and counterweight plate

83.6 kg 102.4 kg

With isolating transformer and insulation monitor

*The weights were only included for both trolley types, if the values are different.

5

GB

REMOVAL OF POLLUTANTS PV800/PV810

Device overview

Item 030

Item 030

6

GB

REMOVAL OF HAZARDOUS SUBSTANCES PV800/PV810

Device overview

Item 010

Item 010

7

Item 020

GB

REMOVAL OF POLLUTANTS PV800/PV810

Disassembly  Disassembly of the stripping protection, unplugging of all cables at the isolating transformer and removal of the isolating transformer  Snipping off the supply line to the insulation monitor just before the monitor and disassembly of insulation monitor  Remove the rear panel covers and conduit covers  Remove the green-yellow protective conductor cables from the rear wall parts  Remove the wiring harness from the open rear wall  Loosen the glued assembly aids by pulling on the attached cables  Snip off the accesses to the switch just before the switch  Unscrew the green-yellow protective conductor cable on the POAG distributor plate

8

GB

RECYCLABLE COMPONENTS PV800/PV810

Device overview

Item 210

Item 100

Item 090 Item 050

Item 120

9

Item 130 Item 090

Item 190

10

GB

RECYCLABLE COMPONENTS PV800/PV810

Device overview Item 110

Item 070

Item 220

Item 210

Item 040

Item 050 11

Item 150

GB

REMOVAL OF POLLUTANTS PV800/PV810

Disassembly  Release the upper and lower rear cover and remove, firstly disconnect the protective conductor cable  If necessary remove the middle rear wall cover and the inside rear wall by loosening the screws, alternatively remove the cable channel cover plates  Disconnect all inserted protective conductor cables  Removal of the lock from the rear wall cover by loosening the screw  Loosen the fastening screws in the spar grooves and remove the inner rear wall  Removal of the components of the inner rear wall by loosening the corresponding screw connections  Lever out the power switch and the side grommets

12

GB

RECYCLABLE COMPONENTS PV800/PV810

Device overview

Item 140 Item 090

Item 190

Item 140

Item 090

Item 170 13

GB

RECYCLABLE COMPONENTS PV800/PV810

Disassembly  Pull off profile caps from the spars  Remove the shelves by loosening the side screws in the spars  Disassembly of the shelf items by loosening the corresponding screw

14

GB

RECYCLABLE COMPONENTS PV800/PV810

Disassembly  Removing the drawer frame by loosening the side fixing screws in the spars  Remove movable drawer towards the front, by loosening the guides  Dismantle the drawer parts by loosening the corresponding screw connections Item 120 Item 110

Item 170

Disassembly

Item 040

15

GB

RECYCLABLE COMPONENTS PV800/PV810

Disassembly  Pulling off the protective conductor cable from the un-plug arrester  Dismantle the chassis parts and the lower frame pan by loosening the corresponding screw connections

Item 160

Item 230

Item 060

Item 110

Item 100

Item 080

16

Pos. 130 Pos. 090

Pos. 190

24

AESCULAP ® – a B. Braun brand Aesculap AG | Am Aesculap-Platz | 78532 Tuttlingen | Germany Phone +49 7461 95-0 | Fax +49 7461 95-2600 | www.aesculap.com

The main product mark ‘Aesculap’ is a registered mark of Aesculap AG. Subject to technical changes. All rights reserved. This document may only be used for the exclusive purpose of obtaining information about our products. Reproduction in any form partial or otherwise is not permitted. Die Hauptproduktmarke ‘Aesculap’ ist eine eingetrage ne Marke der Aesculap AG. Technische Änderungen vorbehalten. Dieses Dokument darf ausschließlich zur Information über unsere Erzeugnisse verwendet werden. Nachdruck, auch auszugsweise, verboten.

TA015042 201809