Universal targeting device for the supine and lateral position

2.3.2

en ®

Aesculap Universal targeting device for the supine and lateral position Legend 1 2 3 4 5 6 7 8

Threaded rod Finger knob Template Indicator Bearer Retaining clip Stud Slide

1.

About this document

Setting the second position angle

Note The right side must be observed and set accordingly with L for Left or R for Right on the template 3. ► Lift indicator 4 until it is freely movable. ► Move indicator 4 to the correct position on template 3 depending on the required angle, see Fig. 3. ► Set indicator 4 down again.

The universal targeting device is now ready to use and can be mounted on the impactor, see Fig. 4.

3.

Validated reprocessing procedure

3.1

General safety information

Note Adhere to national statutory regulations, national and international standards and directives, and local, clinical hygiene instructions for sterile processing. Note For patients with Creutzfeldt-Jakob disease (CJD), suspected CJD or possible variants of CJD, observe the relevant national regulations concerning the reprocessing of products.

Note General risk factors associated with surgical procedures are not described in these instructions for use.

Note Mechanical reprocessing should be favored over manual cleaning as it gives better and more reliable results.

1.1

Note Successful processing of this medical device can only be ensured if the processing method is first validated. The operator/sterile processing technician is responsible for this.

Scope

These instructions for use apply for universal targeting devices for the supine and lateral position. ► For article specific instructions for use and material compatibility and lifetime information, see B. Braun eIFU at eifu.bbraun.com

1.2

Safety messages

Safety messages make clear the dangers to patient, user and/or product that could arise during the use of the product. Safety messages are labeled as follows: WARNING Indicates a possible threat of danger. If not avoided, minor or moderate injury may result. CAUTION Indicates a possible threat of material damage. If not avoided, the product may be damaged.

2.

Clinical use

2.1

Areas of use and limitations of use

2.1.1

Intended use

The universal targeting device is used in hip replacement surgery and specifically in the implantation of a socket, as an orientation aid for the surgeon. The targeting device can be individually adjusted depending on the indication and operating technique.

2.1.2

Indications

Note The manufacturer is not responsible for any use of the product against the specified indications and/or the described applications. The indications correspond to those of the implant system used.

2.1.3

Absolute contraindications

The absolute contraindications correspond to those of the implant system used.

2.1.4

2.2

Safety information

2.2.1

Clinical user

General safety information To prevent damage caused by improper setup or operation, and to not compromise the manufacturer warranty and liability: ► Use the product only according to these instructions for use. ► Follow the safety and maintenance instructions. ► Ensure that the product and its accessories are operated and used only by persons with the requisite training, knowledge and experience. ► Store any new or unused products in a dry, clean, and safe place. ► Prior to use, check that the product is in good working order. ► Keep the instructions for use accessible for the user. Note The user is obligated to report all severe events in connection with the product to the manufacturer and the responsible authorities of the state in which the user is located. Notes on surgical procedures It is the user's responsibility to ensure that the surgical procedure is performed correctly. Appropriate clinical training as well as a theoretical and practical proficiency of all the required operating techniques, including the use of this product, are prerequisites for the successful use of this product. The user is required to obtain information from the manufacturer if there is an unclear preoperative situation regarding the use of the product.

Sterility

The product is delivered in an unsterile condition. ► Clean the new product after removing its transport packaging and prior to its initial sterilization.

2.3

Application

WARNING Risk of injury and/or malfunction! ► Prior to each use, inspect the product for loose, bent, broken, cracked, worn, or fractured components. ► Always carry out a function test prior to each use of the product. Note A symbol of a pair of eyes is marked on the slide 8. The pair of eyes shows from which side the surgeon must view the slide to set the correct angle. The pair of eyes and patient position must always be on the same side, see Fig. 1. Note The angles can be set in increments of 5°.

2.3.1

Note For up-to-date information about reprocessing and material compatibility, see B. Braun eIFU at eifu.bbraun.com The validated steam sterilization procedure was carried out in the Aesculap sterile container system.

3.2

General information

Dried or affixed surgical residues can make cleaning more difficult or ineffective and lead to corrosion. Therefore the time interval between application and processing should not exceed 6 h; also, neither fixating pre-cleaning temperatures >45 °C nor fixating disinfecting agents (active ingredient: aldehydes/alcohols) should be used. Excessive measures of neutralizing agents or basic cleaners may result in a chemical attack and/or to fading and the laser marking becoming unreadable visually or by machine for stainless steel. Residues containing chlorine or chlorides e.g. in surgical residues, medicines, saline solutions and in the service water used for cleaning, disinfection and sterilization will cause corrosion damage (pitting, stress corrosion) and result in the destruction of stainless steel products. These must be removed by rinsing thoroughly with demineralized water and then drying. Additional drying, if necessary. Only process chemicals that have been tested and approved (e.g. VAH or FDA approval or CE mark) and which are compatible with the product’s materials according to the chemical manufacturers’ recommendations may be used for processing the product. All the chemical manufacturer's application specifications must be strictly observed. Failure to do so can result in the following problems: ■ Optical changes of materials, e.g. fading or discoloration of titanium or aluminum. For aluminum, the application/process solution only needs to be of pH >8 to cause visible surface changes. ■ Material damage such as corrosion, cracks, fracturing, premature aging or swelling. ► Do not use metal cleaning brushes or other abrasives that would damage the product surfaces and could cause corrosion. ► Further detailed advice on hygienically safe and material-/value-preserving reprocessing can be found at www.a-k-i.org, link to "AKI-Brochures", "Red brochure".

Relative contraindications

The relative contraindications correspond to those of the implant system used. In the presence of relative contraindications, the user decides individually regarding the use of the product.

2.2.2

Note If there is no final sterilization, then a virucidal disinfectant must be used.

Setting the patient position and first position angle

► Remove bearer 5 from slide 8. ► Set bearer 5 to the required patient position (Lateral or Suspine), see Fig. 2. ► Set the denticulation between the bearer 5 and slide 8 to the required angle (inclination or anteversion). ► Re-attach bearer 5 to slide by releasing the spring 8.

3.3

Reusable products

Influences of the reprocessing which lead to damage to the product are not known. A careful visual and functional inspection before the next use is the best option to determine if a product is no longer functional, see Inspection.

3.4

Preparations at the place of use

► If applicable, rinse non-visible surfaces preferably with deionized water, with a disposable syringe for example. ► Remove any visible surgical residues to the extent possible with a damp, lint-free cloth. ► Transport the dry product in a sealed waste container for cleaning and disinfection within 6 hours.

3.5

Preparing for cleaning

► Disassemble the product prior to cleaning, see Disassembly. ► Open indicator 4 until it no longer lies on template 3.

3.6

Disassembly

Note To disassemble the product, follow the steps for assembly in reverse order see Assembly.

3.7

Cleaning/Disinfection

3.7.1

Product-specific safety information on the reprocessing method

Danger to the patient! The product must not be manually reprocessed. ► Reprocess the product only in a mechanical washer/disinfector. ► Reprocess the product only by manually pre-cleaning followed by cleaning in a mechanical washer/disinfector. Damage to or destruction of the product due to inappropriate cleaning/disinfecting agents and/or excessive temperatures! ► Use cleaning and disinfecting agents approved for aluminum, plastics and high-grade steel according to manufacturer’s instructions. ► Observe specifications regarding concentration, temperature and exposure time. ► Do not exceed the maximum allowable disinfection temperature of 95 °C. ► With PVD coated products, do not use oxidizing process chemicals (e.g. H2O2), as these can cause bleaching or

layer loss. ► Use suitable cleaning/disinfecting agents if the product is disposed of in a wet condition. To prevent foaming and

degradation of the efficacy of the process chemicals: prior to mechanical cleaning and disinfection, rinse the product thoroughly with running water.

3.7.2

Validated cleaning and disinfection procedure

3.9.2

Validated procedure

Specific requirements

Reference

Manual pre-cleaning with brush and subsequent mechanical alkaline cleaning and thermal disinfection

► Use a suitable cleaning brush. ► Use a 20 ml disposable syringe. ► Place the product on a tray that is

Chapter Mechanical cleaning/disinfection with manual pre-cleaning and subsection:

suitable for cleaning (avoid rinsing blind spots).

■ Chapter Manual pre-clean-

► Open indicator 4 until it no longer

■ Chapter Mechanical alka-

lies on template 3.

ing with a brush

► Connect components with lumens

and channels directly to the rinsing port of the injector carriage. ► Keep working ends open for cleaning. ► Place the product on the tray with all product links and joints open.

3.8

line cleaning and thermal disinfecting

Mechanical cleaning/disinfection with manual pre-cleaning

Note The cleaning and disinfection device must be of tested and approved effectiveness (e.g. FDA approval or CE mark according to DIN EN ISO 15883).

Functional test

CAUTION Damage (metal cold welding/friction corrosion) to the product caused by insufficient lubrication! ► Prior to function checks, lubricate moving parts (e.g. joints, pusher components and threaded rods) with maintenance oil suitable for the respective sterilization process (e.g. for steam sterilization: STERILIT® I oil spray JG600 or STERILIT® I drip lubricator JG598). ► Assemble disassembled products, see Assembly. ► Check that the product functions correctly. ► Check that all moving parts are working property (e.g. hinges, locks/latches, sliding parts etc.). ► Check for compatibility with associated products. ► Immediately put aside inoperative products and send them to Aesculap Technical Service, see Technical service.

3.10 Assembly ► Pull and hold template 3 against the spring tension in the direction of finger knob 2. ► Align the groove of the bearer 5 with the rod on the peg 7, see Fig. 5. ► Insert the peg 7 into the hole in the bearer 5 as far as it will go. ► Rotate the bearer 5 around the peg 7, until the slide 8 is positioned over the dentification. ► Release the spring to lock the dentification in place. ► Screw threaded rod 1 into finger knob 2.

3.11 Packaging

Note The cleaning and disinfection device used for processing must be serviced and checked at regular intervals.

► Place the product in its holder or on a suitable tray. Ensure that sharp edges are covered. ► Package trays appropriately for the sterilization process (e.g. in Aesculap sterile containers). ► Ensure that the packaging provides sufficient protection against contamination of the product during storage.

3.8.1

Manual pre-cleaning with a brush

3.12 Steam sterilization

Phase

Step

T [°C/°F]

t [min]

Conc. [%]

Water quality

Chemical

I

Disinfectant cleaning

RT (cold)

>15

2

D–W

Aldehyde-free, phenol-free, and QUAT-free concentrate, pH ~ 9*

Rinsing

RT (cold)

1

Note The product can be sterilized either in disassembled or in assembled condition. ► Check to ensure that the sterilizing agent will come into contact with all external and internal surfaces (e.g., by

II

-

D–W

-

D–W: Drinking water RT: Room temperature *Recommended: BBraun Stabimed fresh

opening any valves and faucets). ► Validated sterilization process

– Disassemble the product – Steam sterilization using fractional vacuum process – Steam sterilizer according to DIN EN 285 and validated according to DIN EN ISO 17665 – Sterilization using fractionated vacuum process at 134 °C/holding time 5 min ► If several devices are sterilized at the same time in the same steam sterilizer: Ensure that the maximum permitted load according to the manufacturers’ specifications is not exceeded.

3.13 Storage ► Store sterile products in germ-proof packaging, protected from dust, in a dry, dark, temperature-controlled area.

► Note the information on appropriate cleaning brushes and disposable syringes, see Validated cleaning and dis-

infection procedure.

4.

Phase I ► Fully immerse the product in the cleaning/disinfectant for at least 15 min. Ensure that all accessible surfaces are moistened. ► Clean the product with a suitable cleaning brush in the solution until all discernible residues have been removed from the surface. ► If applicable, brush through non-visible surfaces with an appropriate cleaning brush for at least 1 min. ► Mobilize non-rigid components, such as set screws, links, etc. during cleaning. ► Thoroughly rinse through these components with the cleaning disinfectant solution (at least five times), using a disposable syringe. Phase II ► Rinse/flush the product thoroughly (all accessible surfaces) under running water. ► Mobilize non-rigid components, such as set screws, joints, etc. during rinsing.

3.8.2

Mechanical alkaline cleaning and thermal disinfecting

Machine type: single-chamber cleaning/disinfection device without ultrasound Phase

Step

Technical service

CAUTION Modifications to medical technology equipment result in loss of approval and can result in forfeiture of guarantee/warranty claims. ► Do not modify the product. ► For service and repairs, please contact your national B. Braun/Aesculap agency. Service addresses Aesculap Technischer Service Am Aesculap-Platz 78532 Tuttlingen / Germany Phone: +49 7461 95-1601 Fax: +49 7461 16-2887 E-Mail: [email protected] Other service addresses can be obtained from the address indicated above.

T [°C/°F]

t [min]

Water quality

Chemical

5.

WARNING Risk of infection due to contaminated products! ► Adhere to national regulations when disposing of or recycling the product, its components and its packaging.

I

Prerinse

<25/77

3

D–W

-

II

Cleaning

55/131

10

FD-W

■ Concentrate, alkaline: – pH ~ 13 – <5 % anionic surfactant

Disposal

Note The user institution is obliged to reprocess the product before its disposal, see Validated reprocessing procedure.

■ working solution 0.5% – pH = 11* III

Intermediate rinse

>10/50

1

FD-W

-

IV

Thermal disinfecting

90/194

5

FD-W

-

V

Drying

-

-

-

In accordance with the program for the cleaning and disinfecting machine

D–W: FD–W:

Drinking water Fully desalinated water (demineralized, low microbiological contamination: drinking water quality at least) *Recommended: BBraun Helimatic Cleaner alkaline ► Check visible surfaces for residues after mechanical cleaning/disinfecting.

3.9

Inspection

► Allow the product to cool down to room temperature. ► Dry the product if it is wet or damp.

3.9.1

Visual inspection

► Ensure that all soiling has been removed. In particular, pay attention to mating surfaces, hinges, shafts, recessed

areas, drill grooves and the sides of the teeth on rasps. ► If the product is dirty: repeat the cleaning and disinfection process. ► Check the product for damage, e.g. insulation or corroded, loose, bent, broken, cracked, worn or severely scratched and fractured components. ► Check the product for missing or faded labels. ► Check the products with long, slim shapes (in particular rotating instruments) for deformities. ► Check the product for damage to the spiral element. ► Check the cutting edges for continuity, sharpness, nicks and other damage. ► Check the surfaces for rough spots. ► Check the product for burrs that could damage tissue or surgical gloves. ► Check the product for loose or missing parts. ► Immediately put aside damaged or inoperative products and send them to Aesculap Technical Service, see Technical service.

6.

Symbols on product and packaging Surgeon's direction of vision

TA013802

2020-03

V6

Change No. 61719