BHM Medical
V4i Instructions for Use rev10 April 2011
Instructions for Use
48 Pages
![Table of Contents General Information ... 5 Foreword ... 5 Service and Support ... 5 Manufacturer Information ... 6 Authorized European Representative ... 6 Definitions Used in this Manual ... 6 Intended Use ... 6 Operational Life ... 6 Equipment Identification ... 7 Verifying the Package Contents ... 7 How to Use this Manual ... 7 Symbols Used ... 8 Safety Instructions... 9 General Instructions ... 9 Safe Working Load ... 9 Important Safety Directions ... 10 Shock Prevention ... 10 Fire and Explosion Prevention ... 11 Human and Environmental Safety Practices ... 11 Battery and Battery Charger Safety Practices ... 11 Equipment Warning Labels ... 11 Part Designation ... 12 Handset ... 13 Chargers ... 13 Slings... 14 How to Use the V4i ... 15 Return to Charge (RTC) ... 16 Emergency Stop (Red Cord) ... 16 Emergency Lowering ... 16 Emergency Brake ... 18 Battery Information ... 18 Indicator Lights ... 18 Charging the Batteries ... 18 Programming the Ceiling Lift ... 20 Using the FIDO Function (Pre-Programmed Positions) ... 20 Use of Slings ... 20 Spreader Bars and Stretcher Frame ... 20 Slings ... 20 Before Approaching the Patient ... 20 Procedure for Using Loop Slings with a Two-Point Spreader Bar ... 21 To Lift a Patient from a Bed ... 22 To Lift a Patient from a Chair ... 23 3](https://images.bioclinicalservices.com.au/awoBZsbo8SFJFi55SjeaBMiy/320w/BHM%20Medical%20-%20V4i%20Instructions%20for%20Use%20rev10%20April%202011%20-%202011-04.png)
Preview
Page 1
V4i
Instructions for Use
001.14150.EN rev. 10 • April 2011
Printed in Canada BHM Medical Inc. reserves the right to change or discontinue any specifications, design, features, model or accessories shown without notice. TM Trade-mark of BHM Medical Inc. All rights reserved. © BHM Medical Inc., 2010 The content of this publication may not be copied either whole or in part without the consent of BHM Medical.
Table of Contents
General Information ... 5 Foreword ... 5 Service and Support ... 5 Manufacturer Information ... 6 Authorized European Representative ... 6 Definitions Used in this Manual ... 6 Intended Use ... 6 Operational Life ... 6 Equipment Identification ... 7 Verifying the Package Contents ... 7 How to Use this Manual ... 7 Symbols Used ... 8 Safety Instructions... 9 General Instructions ... 9 Safe Working Load ... 9 Important Safety Directions ... 10 Shock Prevention ... 10 Fire and Explosion Prevention ... 11 Human and Environmental Safety Practices ... 11 Battery and Battery Charger Safety Practices ... 11 Equipment Warning Labels ... 11 Part Designation ... 12 Handset ... 13 Chargers ... 13 Slings... 14 How to Use the V4i ... 15 Return to Charge (RTC) ... 16 Emergency Stop (Red Cord) ... 16 Emergency Lowering ... 16 Emergency Brake ... 18 Battery Information ... 18 Indicator Lights ... 18 Charging the Batteries ... 18 Programming the Ceiling Lift ... 20 Using the FIDO Function (Pre-Programmed Positions) ... 20 Use of Slings ... 20 Spreader Bars and Stretcher Frame ... 20 Slings ... 20 Before Approaching the Patient ... 20 Procedure for Using Loop Slings with a Two-Point Spreader Bar ... 21 To Lift a Patient from a Bed ... 22 To Lift a Patient from a Chair ... 23
3
Table of Contents
To Lift a Patient from the Floor ... 23 Before Transferring a Patient ... 23 Using Stretcher Frames and Stretchers ... 23 Operating the Exchanger ... 24 Operating the Turntable ... 24 Changing the Speed of Movement ... 25 V4i Programming ... 25 Adjusting the Spreader Bar Height ... 26 Enable/Disable Return to Charge (RTC) ... 27 Preventive Maintenance Schedule ... 28 User Inspections ... 28 Care and Maintenance ... 28 Inspections by an Authorized Service Technician ... 29 Daily Checklist ... 31 Inspection and Cleaning ... 31 Strap Inspection ... 31 Handling and Storage ... 32 Battery Replacement ... 32 Verification of the Charger’s Power Source ... 32 Sling Inspection and Care ... 32 Regular Inspections ... 32 Sling Laundering ... 32 Annual Inspection ... 33 Maintenance Requirements ... 33 Troubleshooting ... 34 Labels on the Lift... 36 Technical Specifications... 37 Lift Dimensions ... 39 Electromagnetic Compliance ... 40 Electromagnetic Emissions ... 40 Electromagnetic Compatibility... 40 Electromagnetic Immunity ... 41 Limited Warranty ... 46
4
General Information Thank you for purchasing the BHM V4i ceiling lift. Your V4i is part of a series of quality products designed specially for home care, nursing homes and other health care uses. We are dedicated to serving your needs and providing the best products available along with training that will bring your staff maximum benefits from every BHM Medical product. Please read this manual thoroughly, and contact us if you have any questions about the operation or maintenance of your BHM Medical equipment.
Foreword Please read this manual in its entirety before using your V4i. The information in this manual is crucial to the proper operation and maintenance of the equipment, and will help protect your product as well as ensure that the equipment performs to your satisfaction. Lifting and transferring a person always presents a potential risk. Some of the information in this manual is important for your safety and must be read and understood to help prevent injuries. BHM Medical strongly advises and warns that to avoid injuries that can be attributed to the use of inadequate parts, only parts designated by BHM Medical should be used on equipment and other appliances supplied by BHM Medical. Furthermore, unauthorized modifications on any BHM Medical equipment may affect its safety. BHM Medical will not be held responsible for any accidents, incidents or deficiencies of performance that occur as a result of any unauthorized modification to its products. Tested according to standards by TUV Product Service and CSA.
Service and Support A service routine must be performed on your V4i by BHM Medical qualified service personnel. This will ensure the safety and good functioning of your product. See section called “Care and Maintenance” in this manual. If you require further information, please contact your local BHM Medical representative which can offer comprehensive support and service programs to maximize the long-term reliability, safety and value of the product. Contact your local BHM Medical representative for replacement parts. Additional copies of this manual can be purchased from your local BHM Medical representative. When ordering, include the Instructions for Use product number (see front page) and equipment identification number.
5
General Information Manufacturer Information
Operational Life
This product has been manufactured by: BHM Medical Inc. 2001 Tanguay Street Magog (Quebec) Canada J1X 5Y5
The equipment is designed and tested for a useful life of seven (7) years or 10,000 transfers-whichever comes first-subject to preventative maintenance as specified in the “Care and Maintenance” section in this manual. Time equivalence between the number of transfers versus the number of years is made clear in the table in Fig. 1.
Authorized European Representative Huntleigh Healthcare Ltd. 310-312 Dallow rd. Luton, UK LU1 1TD
Years
Definitions Used in this Manual WARNING:
Transfers per Day
(10,000 transfers)
4
7
6
4.5
8
3.5 Fig. 1
Means: Failure to understand and follow these instructions may result in injury to yourself and others.
WARNING: The manufacturer cannot ensure full safety for a ceiling lift or an accessory of which the life span has been exceeded.
CAUTION:
The red indicator light on the ceiling lift will blink when it is about halfway to its useful life, and again to indicate the end of the useful life period.
Means: Failure to follow these instructions may cause damage to the product.
The operating life of this equipment corresponds directly to the safe operating time period before a complete overhaul is required. Aging of the cassette, frequency of use (transfers per day), the weight of the patient and maintenance frequency are factors that have an impact on the V4i’s life span. A transfer is defined as the displacement of a patient from one point to another. A transfer cycle includes a lifting and a descending action.
NOTE:
Means: This is important information regarding the correct use of the equipment.
Intended Use The V4i is designed for lifting patients in a homecare setting, at nursing homes and other assisted living centers. Patient transferring is performed under the supervision of an appropriately trained caregiver staff in accordance with the instructions outlined in this manual. All other uses must be avoided.
The expected operational life for fabric slings and fabric stretchers is approximately 2 years from date of purchase. This life expectancy only applies if the slings and stretchers have been cleaned, maintained and inspected in accordance with the BHM Medical Sling Application Guide, the Instructions for Use and the “Preventive Maintenance Schedule”.
The equipment must only be used for the purposes stated above, and must be installed by BHM Medical authorized personnel and in accordance with local codes.
The expected life for other consumable products, such as batteries, fuses, lamps, straps and cords is dependent upon the care and usage of the equipment
6
General Information concerned. Consumables must be maintained in accordance with published Instructions for Use and the “Preventive Maintenance Schedule”.
Equipment Identification The unit's identification number (specification, model, serial number) appears on a silver nameplate attached to the lift’s plastic housing.
Verifying the Package Contents Always ensure that the ceiling lift will be installed by a contractor or installer that has been authorized by BHM Medical. Upon receipt of the equipment, verify it against the packing list to ensure it is complete and inspect the equipment for possible damage due to shipping. If there is any damage, notify the carrier immediately to file a claim. Provide complete information concerning damage claims or shipping errors to your local BHM Medical representative. Include all equipment identification numbers and group part numbers (if any) as described above along with a full description of damaged parts.
How to Use this Manual WARNING: Do not attempt to use this equipment without fully understanding the information contained in this manual. To ensure the safe operation of the V4i, read the entire manual carefully, especially the “Safety Instructions” section, before installing, operating, or servicing this equipment. If anything is not completely understood, please contact your local BHM Medical representative for more details. Failure to comply with warnings in this manual may result in injuries. Keep this manual with the lift and refer to it as required. Make sure that all operators are regularly trained in the use of the equipment according to the information found therein.
7
General Information Symbols Used Symbol
Key to symbols This symbol is accompanied by the name and the address of the authorized representative in the European Community.
This symbol is accompanied by a date to indicate the date of manufacture and by the address of the manufacturer. This symbol indicates the products comply with the medical device directive 93/42/EEC.
This symbol indicates the approval of the Canadian Standards Association.
This symbol is accompanied by the manufacturer's catalogue number.
This symbol is accompanied by the manufacturer's serial number.
This symbol indicates “separate collection” for all batteries and accumulators as per the WEEE Directive.
This symbol refers to the Instructions for Use. This symbol indicates a class II electrical equipment: term referring to electrical equipment in which protection against electric shock does not rely on basic insulation only. This symbol indicates a type BF applied part.
This symbol indicates a risk of pinching
This symbol locates the emergency stop system on the lift
This symbol locates the emergency lowering system on the lift.
Fig. 2
8
Safety Instructions The equipment must be used in accordance with these safety instructions. Anyone using the equipment must also have read and understood the instructions in this manual. If there is anything you are not sure about, contact your local BHM Medical representative.
General Instructions Keep these Safety Instructions with the ceiling lift at all times. Read the Instructions for Use in this manual before installing, operating, or servicing this equipment. WARNING: The V4i is for transferring patients only. Do not use the lift for any other purpose.
WARNING: Always place the sling around the patient according to the instructions enclosed. Failure to do so may result in injuries to you or to others.
CAUTION: Do not drop either the ceiling lift cassette or the batteries, since they may cause internal damage that is not easily seen. If the ceiling lift is suspected to be damaged, contact your local BHM Medical representative for servicing.
Safe Working Load The V4i has been designed with a lifting capacity of 272 kg (600 lb).
WARNING: The V4i is intended to be used for patients whose weight is within a specified safe working load. Do not attempt to lift more than the lowest weight limit indicated on the following: •
the track system;
•
the “maximum load” label on the V4i;
•
on the spreader bar;
•
on the accessories;
•
on the sling.
9
Safety Instructions Important Safety Directions
NOTE: BHM Medical ceiling lifts are specifically designed for KWIKtrak ceiling rail systems, and BHM Medical slings and accessories.
Always ensure that: •
The ceiling lift is installed by an authorized BHM Medical contractor or installer.
•
The equipment is used by trained staff.
•
The track installation will accept a load equal to that of the ceiling lift.
•
Before an attempt is made to move the patient, an assessment is performed by a qualified professional.
•
You are prepared before attempting to transfer a patient.
•
An assessment of the suitability for transfer of a patient who is connected to electrodes, catheters or other medical devices is conducted by qualified personnel before performing the transfer.
CAUTION: Keep all components of the lift clean and dry, and have electrical and mechanical safety checks done as instructed in the “Care and Maintenance” section of this manual.
CAUTION: Excessive exposure of the handset to water (or other liquid) could cause malfunction of the device.
Shock Prevention •
Do not touch or use a lift with bare conductors or a damaged power cord. Electrically live equipment can result in serious injuries. If the lift or charger has any exposed or damaged wires, contact your local BHM Medical representative immediately.
•
Violent impact during transfers is avoided.
•
The spreader bar being used is intended to be used with the V4i and is capable of bearing the patient’s weight.
•
The sling is intended to be used for this lift and can take the weight of the patient.
•
Do not splash or expose electric parts of the device to water or moisture.
•
The sling is not damaged, torn or frayed.
•
•
The lifting procedures outlined in this manual are followed.
•
All controls and safety features are used only according to the rules specified in this manual. Never attempt to force a control or button on the lift.
Check nameplate for input voltage and frequency requirements. These requirements differ by country. Do not attempt to use the lift in an area that has a different voltage and frequency requirement.
•
Do not attempt to expose, service or repair the lift, battery or charger. If any unit is malfunctioning, contact your local BHM Medical representative.
•
Read batteries and charger instructions thoroughly before using or storing them.
•
The charger is not stored in a shower, bath or other areas with high humidity.
•
The sling straps are in good condition and properly fastened.
•
The daily maintenance is carried out before using the lift.
•
Any precautionary or instruction labels that cannot be easily read are replaced.
•
If storing the V4i when it is not in use, the humidity in the storage area does not exceed 80% at 20ºC (68ºF).
•
The ambient temperature range when storing the V4i is between –10ºC and 50ºC (14ºF to 122ºF).
10
Safety Instructions Fire and Explosion Prevention
Battery and Battery Charger Safety Practices
WARNING: Do not place or store the battery under direct sunlight or near a heat source. Do not expose the batteries or battery charger to flames. Do not use the charger in the presence of flammable anaesthetic gases. •
Do not short circuit the battery terminals.
•
Do not incinerate the battery.
WARNING: Do not expose the battery connector or the battery charger to water. The charger is designed for dry areas only and for normal air humidity conditions.
Human and Environmental Safety Practices •
Should the battery casing crack, allowing its contents to come into contact with skin or clothing, rinse immediately with water. If the contents comes in contact with the eyes, rinse immediately with plenty of water and seek medical attention.
•
Inhalation of the contents can cause respiratory irritation. Sensitivity to nickel can cause allergic asthma to result. Seek out fresh air and medical attention.
•
For recycling and disposal of the batteries, the rules according to the WEEE directive (Waste of Electronic and Electrical Components) as well as local laws and regulations must be followed. If not they may explode, leak and cause personal injury. When returning batteries, insulate their terminals with adhesive tape. Otherwise, the residual electricity in used batteries may cause fire or explosion. Fig. 3 below shows the symbols for disposal and recycling.
•
Be careful not to drop the batteries.
•
Only use the charger that has been supplied with the equipment.
•
Do not charge the batteries in an unventilated area.
•
The charger must not be covered or exposed to dust.
•
Do not crush, puncture, open, dismantle or otherwise mechanically interfere with the batteries.
•
Do not store batteries at a temperature higher than 50ºC (122ºF).
Equipment Warning Labels
Fig. 3
11
•
Carefully read the labels on the battery and follow the instructions.
•
Inspect all precautionary labels on the equipment. Order and replace all labels that cannot be easily read.
Part Designation V4i Ceiling Lift and Charger Station
Fig. 4
Legend 1) 2) 3) 4) 5) 6) 7) 8) 9)
10) Safety latch 11) UP button 12) DOWN button 13) Green power light 14) Emergency switch plastic insert 15) Yellow charging light 16) Red maintenance/overload light 17) Cord-connected charger (700.15500) 18) Wall-adapted charger (700-15501)
Ceiling lift Emergency lowering mechanism Allen key Track Charging station Strap Spreader bar Handset Red emergency pull cord
12
Part Designation Chargers
The following refers to Fig. 4 on previous page: • •
• •
•
The yellow charging light flashes while charging and goes solid when charge is finished. The green power light illuminates once the lift is on and ready for use; the green light flashes when the batteries are low. The red light illuminates to confirm that the lift is in the programming mode. The red light also illuminates in the normal mode when the lift goes into overheat protection caused by overuse. The red light flashes when servicing is required (contact customer service).
The V4i units are equipped with either a cordconnected universal charging system (#700.15500) or a wall-adapted charger (#700-15501) that can both be customized to fit the AC voltage outlets where they are solds (see Fig. 4).
Handset The V4i’s handset unit is used to operate the ceiling lift. Each funtion is described in Fig. 5. The UP and DOWN buttons raise or lower the spreader bar. With the four-function model, the LEFT and RIGHT buttons activate a lateral motor to move the lift along the track. If you have a two-function model, the LEFT and RIGHT buttons will not function, and the lift must be moved manually. The PROGRAMMING MODE button allows you to modify the functions of the lift (see Fig. 5). Refer to the “V4i Programming” section for more information. UP
button LEFT
button
700.136XX HANDSET RIGHT
button DOWN
button RETURN TO CHARGE
button
700-138XX HANDSET RIGHT
button DOWN UP PROGRAMMING MODE button
button
button LEFT
button
RETURN TO CHARGE
button
PROGRAMMING MODE button
Fig. 5
13
Slings Compatible Slings
Hammock sling (THA-X & THAI-X)
Hammock 6 sling (THA6-X & THA6I-X)
Quick Fit sling (TIR-X)
Hygienic sling (THY-X)
Combi sling (62600X-X)
Walking sling (TEM-X)
Limb sling (300.20005)
Repositioning sling (624500)
Universal Stretcher (A3510)
Fig. 6
14
How to Use the V4i WARNING: Always read the “Safety Instructions” before using the V4i. •
WARNING: Pay close attention to the safety of the patient as you press the control buttons. Before lifting the patient, make sure that all straps are attached to the spreader bar.
The track must be installed and modified only by BHM Medical authorized personnel and in accordance with local codes.
•
All tracks must be closed with end stoppers or connected to other closed track components.
•
Before use, make sure all end stoppers are in place and secured.
Make sure the sling is not caught on any obstructions (for instance, the wheelchair brakes or armrests). Also make sure that the spreader bar is correctly attached to the ceiling lift. See Fig. 7 below.
NOTE: The unit will not lift or lower when it is in charging position. To begin the transferring procedure: 1) Attach the patient sling. See “Use of Slings” section in the user manual for further information.
Fig. 7 5) To lift the patient, press the UP button.
2) Move the ceiling lift directly over the patient. With the four-function model, use the left and right buttons on the handset (see Fig. 5). With the two-function model, simply hold the ceiling lift’s spreader bar and drag it along the track.
6) Make sure the patient is clear of any obstacles before moving him/her. Guide the patient’s legs if necessary. 7) When the patient is located above the desired point of transfer, press the DOWN button.
3) Use the DOWN button on the handset to lower the spreader bar to a point below the chin of the patient (to avoid the risk of it striking the patient’s face due to a sudden movement).
8) Use the handles on the back of the sling to position the patient when transferring into a chair. Hold the handle firmly as the sling will tilt back to position the patient.
If the patient is lying down, lower the spreader bar down near the patient’s thorax, then install the straps.
9) Once the patient is properly seated and the straps have slackened, remove the sling from around the patient, and off the ceiling lift.
WARNING: Hold the ceiling lift spreader bar with one hand at all times when near a resident.
10) Move the ceiling lift away from the patient. 11) When the V4i is no longer required, return the ceiling lift back to the charging station. With the four-function model, use the right or left buttons or press the return to charge button. With the twofunction model, simply drag the ceiling lift back by the spreader bar. The charging indicator light on the clip-on charging station must be on for the ceiling lift to detect it.
4) Attach the straps to the desired position. See “Use of Slings” section.
Verify the green light on the charger station and the yellow light (flashing or solid) on the ceiling lift to ensure that the charging function is working properly.
15
How to Use the V4i Emergency Stop (Red Cord) NOTE: The V4i is equipped with a safety system to prevent a misuse of the ceiling lift. If the lift is used above the amount specified by the duty cycle, a heat detection system will signal the processor to block the lifting of a load until the temperature of the transmission cools down. In the meantime, it will still be possible to activate the horizontal displacement and down functions. When the overheat protection is engaged, the red light will stay on during the cooling period. In addition, a buzzer will sound if the UP button is pressed. The cooling period is between 10 to 30 minutes depending on ambient conditions.
The emergency stop can be activated at any time to stop the functioning of the ceiling lift. 1) To stop the ceiling lift in any emergency, gently pull the red emergency cord once, until you hear a “click” (see Fig. 4 in the “Part Designation” section of this manual). You will notice that the reset switch’s plastic insert, at the very top of the red cord, has descended. The green power light has also turned off. You may also notice that the patient begins to descend slowly when the emergency stop is activated. This is normal. CAUTION: Do not pull the red emergency cord with excessive force. If the cord is jerked too hard, the ceiling lift may become inoperable.
Return to Charge (RTC)
2) To reactivate the ceiling lift, push up on the reset switch’s plastic insert (for units equipped with infrared handsets pull the red emergency cord again). A green light confirms that the V4i is on and ready for use.
The RTC function is disabled by default (with the exception of units equipped with infrared handsets, whose RTC fuction is enabled by default). To activate this function, please refer to the V4i “Programming” section in this manual.
Emergency Lowering
To engage the return to charge function, press on the return to charge button on the handset for 3 seconds (1 second for infrared units). The spreader bar will raise all the way up to avoid any obstacles during the run. When the lift is at the charging station, the spreader bar lowers by itself to the preselected height so as to be easily accessible.
In the unlikely event of an electrical failure, the V4i has an emergency manual lowering feature. CAUTION: The emergency lowering feature is to be used only in case of emergency.
WARNING: DO NOT make use of the RTC function where there is a patient in the lift, as this could cause injuries to the patient.
If the ceiling lift malfunctions when a patient is being transferred, the emergency lowering device provides a safe way of getting the patient down onto a chair, bed or wheelchair (see Fig. 8). To use it: 1) Pull the red emergency cord.
NOTE: You can stop the return to charge at any time by pressing any button on the handset or pulling on the red emergency cord.
2) Open the small side door to access the lowering mechanism. 3) Remove the 8 mm Allen key on the top of the ceiling lift. Insert the Allen key deep into the axle.
WARNING: Extra care should be exercised when manipulating the handset when transferring a patient that weighs 20 kg (45 lb) or less. The weight detector within the unit that prevents the RTC from functioning when a patient is in the lift can only detect a minimum load of 20 kg (45 lb).
4) Turn the Allen key counter-clockwise to slowly lower the patient. Once the patient is lowered and secure within a chair, bed or wheelchair, call a qualified technician to inspect the ceiling lift.
16
How to Use the V4i
Access emergency
2 lowering system.
1 Pull red emergency cord.
3
Remove Allen key.
4 Turn key counter-clockwise.
Fig. 8
17
How to Use the V4i Emergency Brake
Indicator Lights
The emergency brake consists of a metal bar fixed to the drum and functions similarly to a car seat belt mechanism.
The ceiling lift and the charging system have many indicator lights. It is important to understand their significance for the proper use and comprehension of the ceiling lift (see Fig. 10).
In the unlikely event that of a transmission or motor failure, the centrifugal force produced will quickly throw the metal bar against the frame, blocking the descent.
Charging the Batteries WARNING: Do not operate the charger unit with a damaged cord or if the unit has been dropped or damaged. Do not bend the power cord by force, or place a heavy object on it. This will damage the cord and may cause fire or electrical shock.
Battery Information The life cycle (number of charging cycles) of the batteries is largely dependent on the depth of discharge within each cycle. The more the batteries are drained, the shorter their overall life span. The life of the batteries is also related to such factors as varying temperatures and rest periods between when they are charged and discharged.
The steps for recharging the batteries are as follows: 1) The green indicator light will begin flashing if batteries are low and need to be recharged. If the light does not turn on, verify the “Troubleshooting” section of this manual.
NOTE: To prolong battery life, return the ceiling lift to the charger whenever the ceiling lift is not in use. If the low battery indicator beeps, and a green light flashes, be sure to recharge the batteries as soon as possible. Charge the batteries until the charging indicator light is a solid yellow before using the lift again. This will extend the life of the batteries.
2) With a four-way unit, use the right or left button or press the return to charge button on the handset; if you chose to activate this feature. A protection device prevents the ceiling lift from returning to the charger if a patient is in the ceiling lift during this operation. With a two-way unit, slide the V4i back to the charger until the contact blades on the lift make contact with the charging station.
NOTE: BHM Medical uses sealed lead-acid batteries. These batteries do not have any memory effect. Therefore, batteries should not be completely drained before recharging.
3) The yellow indicator light will flash when the ceiling lift cassette has returned to the charger and the batteries are being charged. Once the charge is complete the light will stop flashing and become a solid yellow light. WARNING: Batteries need to be charged for a minimum of 8 hours prior to the initial use of the lift.
CAUTION: Never leave a ceiling lift with the power on for an extended period of time without returning it to the charger. The batteries will be drained and damaged. See Fig. 9 for a graph illustrating the relationship between the number of lifts versus the load being lifted.
18
How to Use the V4i
Fig. 9 Green power light
Yellow charging light
Red maintenance/overheat light
OPERATING THE LIFT Flashing
Low batteries
Solid
The lift is on and ready to use
STATE OF BATTERIES Flashing
In process of charging batteries
Solid
Charging done; batteries charged
MAINTENANCE Flashing
Maintenance required by your local representative
Solid
Lift was powered up in “service mode” or is under overheat protection
CHARGING Clip-on charger station indicator
Solid green
Clip-on charging station power is on
Solid red
Problem with charger; do not use the charger
Fig. 10
19
How to Use the V4i Use of Slings
If the batteries have been completely drained it could take up to 6-8 hours to completely recharge them. In order to reduce the charging time, refrain from completely draining the batteries and leave the ceiling lift on the charging station between uses.
Spreader Bars and Stretcher Frame WARNING: Spreader bars must only be installed by a qualified person.
Programming the Ceiling Lift
WARNING: Before using the V4i, always ensure the strap attachment pin is installed correctly through the spreader bar socket and lift strap, and that the split ring is correctly inserted through the hole in the pin (see Fig. 7).
The V4i can be programmed so that the user can easily adjust the speed of the horizontal movement, the spreader bar height and the return to charge parameters of the ceiling lift. To learn about the programming mode, see the section “V4i Programming Guide” on pages 25, 26 and 27 of this manual.
Slings
Using the FIDO Function (Pre-Programmed Positions)
The spreader bar that is attached to the V4i determines what slings can be used to transfer a patient. The two-point spreader bar with sling attachment hooks can accommodate any of the BHM Medical loop attachment slings. All slings are color coded for size by having a different colored edge binding or attachment strap coloring:
WARNING: This function can only be activated by qualified personnel.
•
Grey - Extra Extra Small - XXS
1) Using the pre-programmed positions allows the unit to detect stations (positions) located along the track path. The unit will go to the indicated position by using the handset.
•
White - Extra Small -XS
•
Red - Small - S
•
Yellow - Medium - M
2) To do so, indicate to the unit the desired position to go. For an example, to go to the third station push three times on the PROG button followed by the direction (LEFT or RIGHT buttons).
•
Green - Large - L
A range of special purpose slings are available as accessories, for these or for special size slings, contact your BHM Medical representative.
Then the unit goes by itself to the requested station and stay on hold.
WARNING: Only use slings supplied by BHM Medical and that are designed to be used with the V4i. For sling use please refer to the notes on page 10.
If the position you asked for is not correct, you may stop the ceiling lift at any time by pressing any button on the handset. From this position, reprogram the ceiling lift to the new desired position. Count the number of stations from where you are and indicate the direction to go.
Before Approaching the Patient The attendants should always tell the patient what they are about to do. Make sure to have on hand a sling that is of the correct model and of adequate size for transfer with the V4i unit.
20