Users Guide
36 Pages
Preview
Page 1
Flex Focus User Guide
Type 1202
English BB1756-A March 2009
WORLD HEADQUARTERS Mileparken 34 DK-2730 Herlev Denmark Tel.:+45 44528100 / Fax:+45 44528199 www.bkmed.com Email: [email protected] If you have comments about the user documentation, please write to us at the email address above. We would like to hear from you. BK Medical Customer Satisfaction Input from our customers helps us improve our products and services. As part of our customer satisfaction program, we contact a sample of our customers a few months after they receive their orders. If you receive an email message from us asking for your feedback, we hope you will be willing to answer some questions about your experience buying and using our products. Your opinions are important to us. You are of course always welcome to contact us via your BK Medical representative or by contacting us directly.
•
•
•
Scanner Software NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT. BK Medical HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND MS HAS RELIED UPON BK Medical TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR USE. EXPORT RESTRICTIONS. You acknowledge that Windows XP Embedded is of US-origin. You agree to comply with all applicable international and national laws that apply to Windows XP Embedded, including the U.S. Export Administration Regulations, as well as end-user, enduse and country destination restrictions issued by U.S. and other governments. For additional information on exporting Windows XP Embedded, see http://www.microsoft.com/exporting/ The Flex Focus 1202 Ultrasound Scanner is closed. Any modification of or installation of software to the system may compromise safety and function of the system. Any modification of or installation of software without written permission from BK Medical will immediately void any warranty supplied by BK Medical. Such changes will also void any service contract and result in charges to the customer for restoration of the original Flex Focus 1202 system.
Trademarks: Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries. FireWire is a trademark of Apple Computer, Inc. © 2009 BK Medical Information in this document may be subject to change without notice.
Contents Chapter 1
General Information... 5
Chapter 2
Safety Information... 7 Safety Information... 7 Safety Symbols on the Scanner... 7 CE Marks on Electrical Devices... 8 General Safety Precautions... 8 Mechanical Safety... 9 Explosion Hazards... 10 Electrical Safety... 10 ESD Training... 11 Interference... 11 Electrical Noise... 11 Electromagnetic Interference... 12 RF (Radio Frequency) Interference... 12 Installation... 13 Connecting Other Equipment... 14 Connectors... 14 EMC Requirements... 15 Network Connection... 16 Medical Equipment... 16 Non-Medical Equipment... 17 Using the Scanner with a Lithotriptor... 17 Computer Security... 18 Service and Repair... 18 Transducers... 18 During an Examination... 18 Checking the Date... 18 Verifying the Transducer Type... 19 Measurements... 19 Puncture and Brachytherapy... 20 3D... 20 Acoustic Output... 21 General... 21 Monitor Display... 22 Thermal and Mechanical Indices... 23 Acoustic Output Measurement... 24 Functions Affecting Acoustic Output... 24 Default Acoustic Output... 25 Clinical Measurements: Ranges and Accuracies... 25 Geometric Measurements... 27 3
Time Measurements... 27 Doppler Measurements... 28 References... 28 Chapter 3
Getting Started... 31
Index... 33
4
Chapter 1 General Information This user guide is for all versions of the Flex Focus 1202 Ultrasound Scanner from BK Medical, including the Flex Focus and the Flex Focus Solo. The scanner is a 2D and 3D ultrasound echo and flow imaging system for diagnosis, data processing and transfer and guidance of puncture and biopsy. NOTE: Some of the functionality and options described in this guide may not be
available with your version of the scanner. Before using the scanner, make yourself familiar with the information in the accompanying user information documents. Make sure that you also read the transducer user guide and specifications for each transducer that you use. Failure to follow safety instructions or use for purposes other than those described in the user manuals constitutes improper use. Document
Information
Scanner User Guide
Introductory information, safety information, getting started.
Getting Started
User interface, basic operating instructions. Note: this book is part of the scanner user guide.
Scanner Advanced User Guide
Information about advanced functions, glossary.
Product Data sheet for scanner
Specifications for the scanner, including disinfection methods that can be used.
Technical Data CD
Acoustic output data and data about EMC (electromagnetic compatibility) for all transducers
Care, Cleaning and Safety Cleaning, disinfection, sterilization, checking, storing and disposing of BK Medical equipment. Includes environmental limits. Transducer User Guide
Specific instructions for using the transducer and puncture attachments
Product Data sheet for each transducer
Specifications for the transducer, including disinfection methods that can be used.
Table 1-1. User information documentation that accompanies the equipment.
Flex Focus 1202 User Guide (BB1756-A)
General Information
5
6 Chapter 1
March 2009
Flex Focus 1202 User Guide (BB1756-A)
Chapter 2 Safety Information The scanner can be used for continuous operation, but scanning duration for individual patients must not exceed 60 minutes. We recommend, however, that you turn off the scanner at the end of each workday.
Safety Information This user guide contains cautions, warnings and other information about what you must do to ensure the safe and proper performance of the ultrasound scanner. You must also follow local government rules and guidelines at all times. WARNING Warnings contain information that is important for avoiding personal injury. Caution: Cautions contain information and instructions that must be followed to avoid damaging equipment, data or software.
NOTE: Notes contain information that you should be aware of.
Safety Symbols on the Scanner Table 2-1 contains brief explanations of the symbols used to label the scanner. (Some labels in the table may appear on the transducer rather than the scanner itself.) BK Medical disclaims all responsibility for the operating safety, reliability and performance of the equipment if these symbols and warnings are disregarded in any way. Symbol
Name
Description
Caution or Warning
Consult accompanying user guides when you encounter this sign on the instrument, to avoid reducing its safety.
Potential Equalization
Terminal connected to the chassis. Should be connected to corresponding terminals on other equipment to eliminate potential differences.
Ground (earth)
Additional protective ground (earth). BF: Isolated from ground. Maximum patient leakage current under
Type BF
•
Normal condition ≤100μA
•
Single-fault condition ≤500μA
Table 2-1. Symbols on the scanner.
Flex Focus 1202 User Guide (BB1756-A)
Safety Information
7
Symbol
Name
Description
Type BF
BF, defibrillator-proof B: Maximum patient leakage current under
Type B
•
Normal condition ≤100μA
•
Single-fault condition ≤500μA
Sealing
Dust- and immersion-protected according to EN 60529 [1].
Standby
Standby switch on back of scanner unit– used to turn scanner on and off.
Not watertight
Plug may not be immersed (unless it is covered with a special watertight plug cover).
ESD (electrostatic discharge)
Do not touch pins in connectors with this symbol unless you follow ESD precautionary procedures.
WEEE waste
Within the EU, when you discard the equipment, you must send it to appropriate facilities for recovery and recycling.
Table 2-1. Symbols on the scanner. (continued)
CE Marks on Electrical Devices The European Union has introduced directives requiring b marks on devices. Non-medical devices marked with b comply with relevant directives, for example EEC Council Directive 89/336/EEC of 3 May 1989 concerning Electromagnetic Compatibility. BK Medical devices marked with b or c comply with EEC Council Directive 93/42/EEC of 14 June 1993 concerning Medical Devices. b applies to Class I medical devices. c applies to Classes Im, IIa, IIb and III. BK Medical defines classes assuming scanning duration for individual patients does not exceed 60 minutes.
General Safety Precautions The ultrasound scanner is designed and tested in accordance with EN/IEC 60601-1 [2] (Part 1: General requirements for safety) and EN 60601–2–37 [3] (Particular requirements for the safety of ultrasonic medical diagnostic and monitoring equipment). It complies with requirements for Class 1 (protective earth) devices of EN/IEC 60601-1. It also complies with UL 60601-1 [4] and CSA C22.2 No. 601.1– M90 [5]. It fulfills the requirements for dust protection (IP20) for ordinary equipment specified in EN 60529 [1].
8 Chapter 2
March 2009
Flex Focus 1202 User Guide (BB1756-A)
Physicians only Proper training
Caution: Federal law in North America restricts this device to sale to, or on the order of, a physician. WARNING GS-1 Before you attempt to use BK Medical equipment, you should be trained in ultrasonography or be under the supervision of someone who is trained in ultrasonography. You should also be thoroughly familiar with the safe operation of your ultrasound system: read all the user documentation that accompanies it. No further training is required, but BK Medical offers training in how to use the system. Consult your BK Medical representative for information.
Equipment failure
WARNING GS-2 If at any time the scanner malfunctions, or the image is severely distorted or degraded, or you suspect in any way that the scanner is not functioning correctly:
Isolating the scanner
•
Remove all transducers from contact with the patient.
•
Turn off the scanner. Unplug the scanner from the power source (wall outlet or UPS (uninterruptible power supply)) and make sure it cannot be used until it has been checked.
•
Do not remove the scanner cover.
•
Contact your BK Medical representative or hospital technician.
WARNING GS-3 The power supply cord connects the scanner to the line voltage. To isolate the scanner, you must unplug the power supply cord from the power source (wall outlet or UPS). Do this before you try to make any repairs to the system.
Spilled liquids
Caution: Do not spill liquids on the scanner.
Condensation
Caution: Large variations in temperature or humidity may cause water to condense inside the scanner. If this happens, the scanner may fail to operate properly. Always let the scanner come to room temperature before you plug it in. •
Wait at least 2 hours after the scanner has been subjected to major changes in temperature or humidity.
•
If there is visible evidence of condensation, wait at least 8 hours.
Before you use the scanner, make sure that all the safety requirements described in this chapter have been satisfied.
Mechanical Safety Mechanical failure or unintended use of ultrasound equipment can result in physical injury to patients or operators.
Flex Focus 1202 User Guide (BB1756-A)
Safety Information
9
Mechanical injury
WARNING MS-1 Be careful to avoid the following potential sources of injury:
All parts must be stable
•
Parts of the body can be pinched by moveable parts of the scanner, such as the control panel.
•
Tilting the scanner can cause it to be unstable and injure someone.
•
Do not lean or sit on the control panel or any other part of the scanner. The control panel or monitor can break if subjected to heavy weights or impact.
WARNING MS-2 When parts of the scanner can be mounted individually (for example, for use in an operating room) each part must be securely mounted to a stable support so that it does not tip, fall or come loose and injure someone.
Explosion Hazards Explosion hazards
WARNING EH-1 The ultrasound scanner is not designed to be used in potentially explosive environments. It should not be operated in the presence of flammable liquids or gases, or in oxygen-enriched atmospheres. There is a possible explosion hazard if the scanner is used in the presence of flammable anesthetic. The scanner should be placed at least 25cm (10 inches) from the patient. The ultrasound scanner contains a lithium battery. Never remove or replace this battery. The lithium battery must not be removed except by a BK Medical service representative.
Electrical Safety Do not use a power strip
WARNING ES-1 Do not plug the scanner into an ordinary power strip. If the ground connection fails, this is dangerous because
10 Chapter 2
•
the total leakage current for all the connected equipment can exceed the limits specified in EN/IEC 60601-1 [2] (Part 1: General requirements for safety).
•
the impedance of the ground connection could exceed the limits specified in EN/IEC 60601-1.
March 2009
Flex Focus 1202 User Guide (BB1756-A)
Leakage current
WARNING ES-2 When the equipment is used with 230V (and you believe the leakage current would be within the UL limit if you were using 120V), power to the equipment must come from an installation or supply unit with a center-tapped, 240V single-phase circuit. This will make sure that chassis leakage current during single fault condition fulfills the requirements specified in UL60601-1 [4] (limit of 300µA). If power is not supplied in the way specified, the leakage current can be as high as 500µA, the limit specified in EN/IEC 60601-1 [2] (Part 1: General requirements for safety).
Electrical shock
WARNING ES-3 You risk electrical shock if you try to get inside the scanner (other than opening a cover to access connectors described in the user guide). Do not allow anyone but qualified service personnel to service the scanner.
ESD Training Anyone using the equipment must be able to recognize the ESD symbol and understand how to take the necessary precautionary procedures, as described in the warning below. Caution: Do not touch pins in connectors that have this symbol. Do not connect anything to them unless you follow these ESD (electrostatic discharge) precautionary procedures: ESD
•
Discharge your body to ground before you touch the pins with your hand or a tool. For example, touch an unpainted metal part of the scanner cover.
•
You can use a wrist strap connected to the additional protective ground or potential equalization terminal on the scanner if that is more convenient.
Interference The Flex Focus 1202 Ultrasound Scanner is suitable for use in all establishments, other than domestic establishments and those directly connected to the public lowvoltage power supply network that supplies buildings used for domestic purposes.
Electrical Noise Electrical noise
WARNING EN-1 Electrical noise from nearby devices such as electrosurgical devices – or from devices that can transmit electrical noise to the AC line – may cause disturbances in ultrasound images. This could increase the risk during diagnostic or interventional procedures.
Flex Focus 1202 User Guide (BB1756-A)
Safety Information
11
Electromagnetic Interference Medical electrical equipment requires special precautions regarding EMC (electromagnetic compatibility) [6]. You must follow the instructions in this chapter when you install the scanner and put it into service. If the image is distorted, it may be necessary to position the scanner further from sources of electromagnetic interference or to install magnetic shielding. Other equipment nearby
WARNING EMC-1 Do not use this equipment adjacent to other equipment. If you must place it next to or stacked with other equipment, verify that it operates normally there and neither causes nor is affected by electromagnetic interference.
EMC noise can reduce the usable image depth. Therefore, in order to avoid having to repeat an ultrasound examination, you must make sure beforehand that the ultrasound system can be used for the examination. Repeating an examination can be regarded as a potential risk that should be avoided, especially if the examination involves transducers used intracorporeally or transducers used for puncture.
RF (Radio Frequency) Interference Portable and mobile RF (radio frequency) communication equipment can affect the scanner, but the scanner will remain safe and meet essential performance requirements. An ultrasound scanner intentionally receives RF electromagnetic energy for the purpose of its operation. The transducers are very sensitive to frequencies within their signal frequency range (0.3MHz to 80MHz). Therefore RF equipment operating in this frequency range can affect the ultrasound image. However, if disturbances occur, they will appear as white lines in the ultrasound picture and cannot be confused with physiological signals. Possible interference sources
Caution: Other equipment may interfere with the scanner, even if that other equipment complies with CISPR (International Special Committee on Radio Interference) emission requirements.
Use specified equipment only
Caution: If you use accessories, transducers or cables with the scanner, other than those specified, increased emission or decreased immunity of the system may result.
12 Chapter 2
March 2009
Flex Focus 1202 User Guide (BB1756-A)
Installation Installation safety requirements
Original power cords
WARNING I-1 To ensure safe performance, a qualified electrician or hospital safety personnel must verify that the ultrasound scanner is correctly installed and that it complies with the following safety requirements: •
Use only the original power supply cord. In the USA, this is fitted with a hospital grade three-prong grounded power plug. Never try to remove or change the plug on the power supply cord.
•
All equipment must only be connected to a grounded AC power supply (or wall outlet) that meets EN/IEC/NEC requirements or applicable local regulations. The examination room’s grounding system should be checked regularly by a qualified electrician or hospital safety personnel.
•
Never use extension cords. The increased length of the cord will increase the resistance of the protective ground conductor and may increase the equipment’s leakage current beyond an acceptable level.
•
Keep power cords, sockets and plugs clean and dry at all times.
•
Make sure that the power supply cord cannot be accidentally disconnected from the power source or the scanner.
If the original power cords are missing or damaged, you must order new ones from your local BK Medical representative. Additional Protective Ground and Potential Equalization An additional protective ground can be connected to the control panel, see Fig 2-1.
terminal underneath the
The potential equalization terminal underneath the control panel is connected to the scanner chassis. It can be connected to corresponding terminals on other equipment to eliminate potential differences. Do NOT use it for additional protective grounding.
Figure 2-1. The terminals for potential equalization are underneath the control panel.
Flex Focus 1202 User Guide (BB1756-A)
and additional protective ground
Safety Information
13
Connecting Other Equipment Connection guidelines
WARNING C-1 Follow the guidelines in EN60601-1-1[7] (Safety requirements for medical electrical systems) when you connect the scanner to other equipment.
Connectors PC connectors for connecting the scanner to other equipment such as printers and video equipment are located in the neck of the scanner. To access them, unscrew the screw on the bottom of the neck and remove the connector cover. See Fig 2-2.
Connector cover
Unscrew here to remove connector cover
Figure 2-2. Flex Focus connector cover.
Some connectors are used by the scanner. Do not use connectors that are not labelled in Fig 2-3. More information about the connectors is in Table 2-2. Information about the cables to use is in Table 2-3.
Auxiliary power outlet - for approved printers only
DVI-I Power supply cord goes here
Figure 2-3. Connectors in the neck of the Flex Focus scanner.
14 Chapter 2
March 2009
Flex Focus 1202 User Guide (BB1756-A)
Symbol DVI-I
Connector
Additional Information
DVI-I
connector for auxiliary DVI or VGA monitor
Composite/S-video In Composite/S-video Out Audio In Audio Out 4 USB 2.0 connectors, A-type 500mA current limit on each
FireWireTM 10/100/1000 Ethernet
LAN: 10/100/1000 LAN connector, RJ45
Table 2-2. Connectors in the neck of the Flex Focus scanner.
EMC Requirements To fulfill EMC requirements, cables attached to the scanner must be shielded and no longer than 5 m. Connector name
Cable type
Type and length
DVI-I
Dual link
Shielded, 5 m
S-video/composite In
S-video
Shielded, 5 m
S-video/composite Out
S-video
Shielded, 5 m
Audio In
Stereo, 3,5 mm jack
Shielded, 5 m
Audio Out
Stereo, 3,5 mm jack
Shielded, 5 m
USB 1
USB, 2.0
Shielded, 5 m
USB 2
USB, 2.0
Shielded, 5 m
USB 3
USB, 2.0
Shielded, 5 m
USB 4
USB, 2.0
Shielded, 5 m
FW400
Firewire
Shielded, 5 m
10/100/1000 Ethernet
Network, CAT6E
Shielded, 5 m
Table 2-3. List of cables used in testing for EMC compliance Flex Focus 1202 User Guide (BB1756-A)
Safety Information
15
Do not attach transducers and other accessories unless the user guide for the transducer or accessory states that it can be used with this scanner. Attaching other equipment may cause an increase in electromagnetic emissions or may cause the scanner to be more sensitive to electromagnetic interference.
Network Connection The scanner must not be galvanically connected to a computer network (DICOM®) that has not been isolated. If the network is not isolated, the scanner must be connected via a network isolator DP0925 (see Accessories in Product Data sheet).
Medical Equipment Power source
WARNING ME-1 Follow the guidelines in EN60601–1–1 [7] (Safety requirements for medical electrical systems). Equipment that complies with the requirements of EN/IEC 60601–1 [2] (Part 1: General requirements for safety), UL 60601-1 [4] or CSA C22.2 No. 601.1–M90 [5] can be connected to the scanner, but one of the following conditions must be fulfilled: •
Each piece of equipment is plugged directly into an independent wall power outlet. or
•
The scanner and other equipment are plugged into an external common isolation transformer in order to control the leakage current during a ground connection fault.
If in doubt, contact your local BK Medical representative.
Printers and auxiliary power outlet
WARNING ME-2
Standby switch does not turn off outlet
The auxiliary power outlet is still live even when the standby switch on the scanner is turned off. In order to remove voltage from this outlet, you must unplug the power supply cord from the power source (wall outlet or UPS).
16 Chapter 2
An approved printer, specified in the Product Data sheet, can be connected to the internal auxiliary power outlet on the scanner. Do not use the auxiliary power outlet on the Flex Focus 1202 for any other equipment.
March 2009
Flex Focus 1202 User Guide (BB1756-A)
Non-Medical Equipment WARNING NME-1 Follow the guidelines in EN60601–1–1 [7] (Safety requirements for medical electrical systems). If you connect non-medical equipment (instruments that do not comply with safety requirements for medical equipment, such as a video monitor, video recorder, endoscopic camera control unit or other documentation device), this equipment must be placed outside the patient environment (1.5m from the bed, for example). The equipment must fulfill the relevant EN standard or other applicable national or international standard. One of the following conditions must be fulfilled: •
The scanner and other equipment are plugged into an external common isolation transformer in order to control the leakage current during a ground connection fault.
or •
The scanner is grounded with an additional safety ground connection (see “Additional Protective Ground and Potential Equalization” on page 13).
If in doubt, contact your local BK Medical representative.
Using the Scanner with a Lithotriptor Special considerations apply if you are using a lithotriptor with the scanner. The lithotriptor must comply with the guidelines in EN60601–1–1 [7] (Safety requirements for medical electrical systems). You must have a license installed in order to use a lithotriptor with the scanner. You must always follow instructions in the manufacturer’s user guide for the lithotriptor. Power Connections Do NOT connect a lithotriptor to the auxiliary power outlet. Plug the scanner and the lithotriptor directly into independent wall power outlets. Connecting the Scanner to the Lithotriptor Connect the lithotriptor to a USB connector on the scanner. If necessary, use a USB RS-232 adapter cable. Follow the connection instructions in the manufacturer’s user guide for the lithotriptor system. The connections must follow the guidelines given in EN 60601– 1–1 [7] (Safety requirements for medical electrical systems).
Flex Focus 1202 User Guide (BB1756-A)
Safety Information
17
Computer Security When the Flex Focus is connected to a hospital network, BK Medical does not take any responsibility for computer viruses from the network that may infect the Flex Focus. Check external media
Caution: You must perform a virus check on any external storage medium (USB device or DVD) to make sure that it is virus-free before you connect it to the scanner.
Service and Repair Authorized personnel
WARNING SR-1 Service and repair of BK Medical electromedical equipment must be carried out only by the manufacturer or its authorized representatives. BK Medical reserves the right to disclaim all responsibility, including but not limited to responsibility for the operating safety, reliability and performance of equipment serviced or repaired by other parties. After service or repairs have been carried out, a qualified electrician or hospital technician should verify the safety of all equipment.
Transducers Electrical shock
WARNING T-1 The transducer sockets contain terminals with 5V. Do not touch the patient while you are touching an uncovered socket.
Type B transducers
WARNING T-2 When using Type B (non-isolated) transducers, carefully check all electrical equipment within the patient area. Also, consider using additional protective grounding.
Electrical burns
WARNING T-3 Do not leave transducers in contact with the patient when using HF electrosurgical equipment.
BK Medical transducers fulfill EMC requirements when they are outside as well as inside the patient’s body.
During an Examination Checking the Date Before you start scanning, verify that the date displayed on the screen is correct. 18 Chapter 2
March 2009
Flex Focus 1202 User Guide (BB1756-A)
Date
WARNING Exam-1 An incorrect date will make documentation of the image incorrect and may also cause some calculated values to be incorrect.
Patient ID required
WARNING Exam-2 You must enter a new patient ID before you scan a new patient. Otherwise the documentation will not contain the correct patient identification, and you will not be able to capture images and clips. We recommend that you enter the complete name of the patient.
Verify patient ID
WARNING Exam-3 Verify that the patient name and ID are correct.
Verifying the Transducer Type Type number displayed must match number on transducer
WARNING Exam-4 Before you start to scan, verify that the type number on the transducer matches the number displayed on the screen.In case of any inconsistency, stop scanning, turn off the scanner, and contact your local BK Medical representative.
Measurements Pay careful attention when you position cursors to make measurements on a scanned image or on a Doppler curve. Polygon measuring tool
WARNING M-1
Using Doppler curves
WARNING M-2
When you use the polygon measuring tool, if the sides of the polygon intersect (as in forming a curve like a figure eight, for example), the area calculation is incorrect. In this case, the calculated area of the polygon is the area of the bigger loop minus the area of the smaller loop.
Drawings of Doppler curves, manual and automatic, are meant as tools for positioning cursors so that measurements based on the curves can be calculated automatically. The scanner has no facilities for checking whether the automatic measurements are reasonable. Curves drawn on very noisy spectra may lead to misplacement of measurement cursors. Make sure that measurement cursors are positioned so that the results are reasonable. If they are not, you must adjust the position of the cursors manually. Flex Focus 1202 User Guide (BB1756-A)
Safety Information
19
Puncture and Brachytherapy Verify transducer type number
WARNING P-1
Verify puncture guide type number
WARNING P-2
Offset changes
WARNING P-3
Before you start to scan, verify that the type number of the transducer matches the number displayed on the screen. If they do not match, the puncture line on the screen may not correspond to the true puncture path in the tissue. In case of any inconsistency, stop scanning, turn off the scanner, and contact your local BK Medical representative.
Verify that the type number of the puncture guide displayed on the screen corresponds to the puncture guide that you are actually using. If the number is incorrect, the puncture line on the screen may not correspond to the true puncture path in the tissue.
Changes you make to the offset of a programmable puncture guide or brachy matrix will affect ALL programmable puncture guides and brachy matrices. This could lead to incorrect puncture lines or matrix positions for a different guide than the one you wanted to change.
Brachytherapy Verify matrix type and coordinates
WARNING B-1
Verify userdefined brachy matrix
WARNING B-2
Verify matrix alignment
WARNING B-3
Verify that the brachy matrix type and coordinates displayed on the screen agree with the actual matrix template you are using.
If you create a user-defined brachy matrix, it is your responsibility to verify that the matrix that appears on the screen corresponds to the physical brachy matrix you are using.
Before you use the brachy matrix for seed implantation, check the matrix offset value to verify that it corresponds with the chosen matrix. Then check the matrix alignment. See Care, Cleaning & Safety for instructions.
3D Pay particular care to the following safety issues when operating the 3D system.
20 Chapter 2
March 2009
Flex Focus 1202 User Guide (BB1756-A)