Autoclavable SoftWrap Pulse Oximetry Sensors Directions for Use V2.3

Instructions for use: Reusable SoftWrap® Pulse Oximetry Sensors DIRECTIONS FOR USE ® Intended Use: Bluepoint Medical SoftWrap oximetry sensors are indicated for use in continuous non-invasive monitoring of arterial oxygen saturation and pulse rate. They are original or fully compatible replacement sensors intended for use with major brands of pulse oximeters and patient monitors. Select the sensor model number that matches the brand of oximeter or patient monitor that you are using. Precautions: For further instructions, warnings and precautions refer to the operating instructions provided with your oximeter. Do not autoclave. CAUTION: Federal (USA) law restricts this device to sale by or on the order of a physician. Warnings: Match the sensor model with your brand of oximeter. A mismatch may cause patient injury, inaccurate measurements or equipment damage. Check the sensor every 8 hours and reposition to an alternate location every 24 hours. Avoid application of the sensors to oedematous or fragile tissue. Do not use the sensor if it is damaged. Use of a damaged sensor could cause patient injury or equipment failure. Excessive patient motion, excessive ambient light, electromagnetic interference, dysfunctional haemoglobin, low perfusion, intravascular dyes, finger nail polish and long or artificial finger nails may affect the sensor performance and the accuracy of the measurement. Note: The materials used in the manufacture of the sensor contain no natural latex protein. The materials have undergone extensive bio-compatibility testing. Further information is available upon request. Application of the Sensor 1. Connect the sensor cable to the Bluepoint Medical adaptor cable that fits your oximeter or directly to the patient monitor. Then switch on the oximeter and verify proper operation. 2. Select the sensor site on the patient. The preferred sensor sites are the index finger for adults and paediatrics, the hand for infants and on the foot below the toes for neonates. 3. Apply the sensor on the patient:  Position the emitter and detector directly opposite each other.  Apply the sensor firmly but not too tightly. 4. Secure the sensor using an adhesive or foam wrap. 5. Visually monitor the sensor site to ensure the integrity of the skin. 6. Secure the lead with medical tape.

Adult / Paediatric

Infant

Neonatal

Environmental Requirements  Operating temperature range: 10° - 40° C (50° -104° F)  Storage and transportation temperature range: 0° - 50° C (32° -122° F)  Relative humidity: 0 - 75% non-condensing SPO2 Accuracy 70 - 100%: Arms <3.0% 0 - 69%: Unspecified Accuracy test methods are available from the manufacturer upon request. LED Specifications LED

Wavelength

Radiant Power (typical)

Brand

Red

660 nm

3.5 mW

All below

Infrared

885 nm

3.5 mW

Nellcor, CSI

890 nm

3.5 mW

HP/Philips

905 nm

3.5 mW

Datex, BCI, Bluepoint Medical

910 nm

3.5 mW

Nonin

935 nm

3.5 mW

Nihon-Kohden

940 nm

3.5 mW

Ohmeda, Novametrix

Disposal Follow local regulations governing disposable recycling plans regarding disposal or recycling of device components. A list of component materials is available by contacting Bluepoint Medical. All registered trademarks recognized. Bluepoint Medical Model

Oximeter Brand

Cable Length

W4001

Nellcor

0.90 m

W4002

Nellcor

2.00 m

W4006

HP/Phillips

2.95 m

W4007

HP/Phillips

2.00 m

W4011

Datex

0.90 m

W4012

Datex

2.95 m

W4013

GE/Datex

2.95 m

W4016

Ohmeda

2.95 m

W4017

Ohmeda

1.00 m

W4021

BCI

1.20 m

W4026

Nonin

0.90 m

W4036

CSI

0.90 m

W4037

CSI

2.95 m

W4041

Novametrix

2.95 m

W4046

Nihon-Kohden

2.95 m

W4047

Nihon-Kohden

1.60 m

W6500

Bluepoint Medical

1.20 m

W6501

Bluepoint Medical

0.30 m

CE0482 Bluepoint Medical GmbH & Co. KG

Cleaning the Sensor To clean the sensor between uses or between patients, wipe the sensor surfaces with alcohol.

An der Trave 15 23923 Selmsdorf Deutschland/Germany Email: [email protected] Homepage: www.bluepoint-medical.com Instructions for Use: Reusable SoftWrap® Pulse Oximetry Sensors V2.3 EN/DE/FR/ES