Carestream Health Inc
Q-Rad System Operators Manual Rev B
Operators Manual
24 Pages

Preview
Page 1
™
Q-Rad System
Operator’s Manual
Manual Part No. 6J5063 Revision B
EU Authorized Representative: Medizintechnik Berlin GmbH Altentreptower, Strasse 59 12683 Berlin - Germany Phone: +49-302-82 4726 Fax: +49-302-82 6382 E-mail: Medizintechnik.Berlin.GmbH@t-online.de
The original release of this manual dated 2011-02-24 (February 24, 2011) was drafted in the English language by Quantum Medical Imaging, LLC.
This manual is copyrighted and all rights are reserved. No portion of this document may be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine readable form without prior consent in writing from Quantum Medical Imaging, LLC. (QMI)
Copyright © 2011 QMI
Quantum Medical Imaging, LLC 2002-B Orville Drive North Ronkonkoma, NY 11779-7661 USA Phone: (631) 567-5800 Fax: (631) 567-5074 E-mail: info@qmiteam.com www.quantummedical.net
Made in U.S.A.
Revision History
Revision
Date
Pages
Notes
A
2011-02-24
---
Initial Release
B
2011-11-02
All
Various
Q-Rad System Quantum Medical Imaging
Revision B
i
Revision History
REVISIO N
DATE
PAGES
NOTES
A
2011-0224
---
Initial Release
B
2011-1027
All
Various
THIS PAGE INTENTIONALLY LEFT BLANK
Revision B
ii
Q-Rad System Quantum Medical Imaging
Chapter 1: General Information Instructions for Use...1-3 Overview...1-4 Component Weights...1-6 Generators (Cabinet)...1-6 Generators (Control Panel)...1-6 Tables...1-6 Tube Supports...1-6 Upright Cassette Holders...1-6 Heat Dissipation...1-7 Generators...1-7 X-Ray Tube...1-7 Tables...1-7 Tube Supports...1-7 Upright Cassette Holders...1-7 System Operating Environment...1-7 Q-Rad Radiographic System...1-7 Transport and Non-Operating Environment...1-7 System Configuration...1-8 Q-Rad Floor-Mounted System...1-8 Q-Rad “CS Series” Ceiling-Mounted System...1-9 Intended Use...1-11 General Application Specification...1-11 Cleaning, Preventive Inspection and Maintenance...1-11 Instructions for Disposal of Waste Equipment...1-11 Labeling...1-12 Power Disconnection...1-16 Detachable Parts and Accessories...1-17
Q-Rad System Quantum Medical Imaging
Revision B
1-iii
Revision B
1-iv
Q-Rad System Quantum Medical Imaging
Chapter
1
CHAPTER 1: GENERAL INFORMATION
1-1
THIS PAGE INTENTIONALLY LEFT BLANK
1-2
Chapter 1 General Information Instructions for Use The instructions for using Quantum’s Q-Rad Radiographic System, including an explanation of the function of controls, displays and signals, and the sequence of operation, are contained in each of the system component user’s manual indicated in Table 1-1. WARNING: This equipment must be operated with reasonable care. Manufacturer’s equipment recommendations described in this manual must be observed. CAUTION: Use a focal spot-to-film distance as large as possible in order to keep the absorbed dose to the patient as low as reasonably achievable. CAUTION: During each exposure, the individual operating the X-ray machine must exit the radiographic operatory and stand behind a leaded wall.
Q-Rad System Quantum Medical Imaging
Revision B
1-3
Chapter 1 General Information Overview This chapter describes the configurations of the Q-Rad Radiographic System, which typically includes Quantum Medical Imaging HF Series X-ray Generators, radiographic tables, free-standing or overhead tube support, upright cassette holder, collimator, X-ray tube, ion chamber (when equipped with AEC option), and image receptor. Detailed instructions for successful integration of the compatible Quantum components are published in the Service Manuals for each of the various system components. Table 1-1. Q-Rad System Components User/Service Documents
Revision B
1-4
Component Type
Model(s)
User Manual P/N
Service Manual P/N
X-ray Generator, Single-phase, non-Stored Energy
QG-25, QG-25-5, QG-32, QG-32-5, QG-40, and QG-40-5
Odyssey: DC30-010 Quest: DC30-015 Q-Vision: DC30-101
Odyssey: DC30-011 Quest: DC30-063 Q-Vision: DC30-101
X-ray Generator, Single-phase, Stored Energy
QG-20-SE, QG-32-SE, QG-40-SE, QG-50-SE
Odyssey: DC30-010 Quest: DC30-015 Q-Vision: DC30-101
Odyssey: DC30-011 Quest: DC30-063 Q-Vision: DC30-101
X-ray Generator, Three-phase
QG-32-2, QG-32-3, QG-40-2, QG-40-3, QG-50, QG-50-2, QG-65, and QG-80
Odyssey: DC30-010 Quest: DC30-015 Q-Vision: DC30-101
Odyssey: DC30-011 Quest: DC30-063 Q-Vision: DC30-101
TechVision Supplementary Generator Control Panel
QG-TV-Q, QG-TV-IP-Q, QG-TV-F, QG-TV-IP-F, QG-TV-C, QG-TV-IP-C
DC30-048
DC30-049
Radiographic Table, Fixed, Non-Float-Top, Enclosed Base
QT-730
DC30-003
DC30-003
Radiographic Table, Non-Elevating Tabletop
QT-740
DC30-006
DC30-007
Radiographic Table, Elevating Tabletop
QT-750
DC30-006
DC30-007
Tube Support, Floor/Wall Mounted
QS-500
DC30-034
DC30-005
Tube Support, Free-Standing (Floor) Mounted
QS-550
DC30-034
DC30-009
Q-Rad System Quantum Medical Imaging
Chapter 1 General Information Table 1-1. Q-Rad System Components User/Service Documents Component Type
Model(s)
User Manual P/N
Service Manual P/N
Tube Support, Overhead (Ceiling) Mounted, Non-Tracking
RS-580
DC30-027
DC30-019
Radiographic Upright Cassette Holder
QW-420, QW-420-S, QW-420-D, QW-400
DC30-039
DC30-040
Collimator, Manual
PROGENY MC150
00-02-1078
00-02-1078
HUESTIS 150MC
CM-21-001
CM-21-001
PROGENY Linear II
00-02-1559
00-02-1559
PROGENY Linear IV
00-02-1517
00-02-1517
PROGENY Linear MC150 Pinnacle
00-02-1566
00-02-1566
TOSHIBA E7239X, E7242X, E7252X, E7254X, E7869X
Refer to the datasheet provided with the X-ray tube
Refer to the datasheet provided with the X-ray tube
Collimator, Automatic
X-ray tube
VARIAN RAD-14, RAD-60, RAD-92 DUNLEE DA 1092
Q-Rad System Quantum Medical Imaging
Revision B
1-5
Chapter 1 General Information Component Weights Generators (Cabinet) Single-Phase, non-Stored Energy (SE) units: 32, 40, and 50 kW, SE units: Three-Phase units:
135.2 kg (298.0 lb) 195.5 kg (431.0 lb) 172.4 kg (380.0 lb) without internal High Speed Starter (HSS) 176.0 kg (388.0 lb) with internal High Speed Starter (HSS)
Generators (Control Panel) Odyssey (without pedestal): Odyssey (with pedestal): Quest (without pedestal): Quest (with pedestal): Q-Vision: TechVision Option:
2.3 kg (5.0 lb) 11.3 kg (25.0 lb) 1.8 kg (4.0 lb) 10.9 kg (24.0 lb) 5.9 kg (13.0 lb) 4.3 kg (9.5 lb)
Tables Model QT-730: Model QT-740: Model QT-750:
79.4 kg (175.0 lb) 158.8 kg (350.0 lb) 226.8 kg (500.0 lb)
Tube Supports Model RS-580: Model QS-550: Model QS-500:
361.1 kg (796.0 lb) 272.2 kg (600.0 lb) 230.4 kg (508.0 lb)
Upright Cassette Holders Model QW-420: Model QW-420-S: Model QW-420-D: Model QW-400:
Revision B
1-6
102.1 kg (225.0 lb) 102.1 kg (225.0 lb) 90.7 kg (200.0 lb) 45.4 kg (100.0 lb)
Q-Rad System Quantum Medical Imaging
Chapter 1 General Information Heat Dissipation Generators Cabinet Typical Heat Output: 3600 BTU per hour Control Panel Typical Heat Output: 130 BTU per hour X-Ray Tube Max. Heat Output (600 khu tube):
2000 BTU per hour
Tables QT-730 Typical Heat Output: QT-750 Typical Heat Output: QT-740 Typical Heat Output:
40 BTU per hour 400 BTU per hour 100 BTU per hour
Tube Supports QS-500/QS-550: RS-580 Typical Heat Output:
200 BTU per hour Max. 341 BTU (100 W) per hour
Upright Cassette Holders Typical Heat Output:
50 BTU per hour
NOTE: The above calculations are typical, based upon average usage. Air circulation around the electronic cabinets must be provided. This includes the sides, back, front, and top of cabinet.
System Operating Environment Q-Rad Radiographic System Ambient Temperature: Relative Humidity: Atmospheric Pressure:
10–40 °C 15–75 % 700–1060 hPa
Transport and Non-Operating Environment Ambient Temperature: Relative Humidity: Atmospheric Pressure:
Q-Rad System Quantum Medical Imaging
-25 to +55 °C 5–95 % 500–1060 hPa
Revision B
1-7
Chapter 1 General Information System Configuration The Quantum Q-Rad System consists of a combination of integrated radiographic components, typically including an X-ray generator, X-ray tube and tube support, collimator, radiographic table, and an upright cassette holder. Different types of image receptors may be utilized with the Q-Rad System, including computed radiography (CR) receptors, as well as conventional analog film cassettes.
Q-Rad Floor-Mounted System The Q-Rad Floor-Mounted system is configured around either a free-standing, floor-mounted tube support (Model QS-550) or a wall/ceiling mounted tube support (Model QS-500). Because the free-standing version does not require wall attachment for support, it provides enhanced freedom of movement in the patient vicinity for the operator. Recumbent examinations are accomplished utilizing an elevating (Model QT-750) or the non-elevating (Model QT-740 and QT-730) radiologic tables. Standing (weight-bearing) examinations are performed using an upright, non-tilting (Model QW-420 Series) chest stand (cassette holder). The X-ray generator is available in various power output and operator control panel types, with the typical configuration including a 80 kW output generator with an Odyssey operator control. Table 1-2. Q-Rad Floor Mounted System COMPONENT GENERATOR
COMPONENT DESIGNATION QG1
COMPONENT MODEL# Single-Phase: QG-25-1, QG-32-1, QG-40-1 Stored Energy: QG-20-SE, QG-32-SE, QG-40-SE, QG-50-SE Three-Phase: QG-32-2, QG-32-3, QG-40-2, QG-40-3, QG-50-3, QG-65-3, QG-80-3
GENERATOR CONTROL PANEL
OCP1
Quest Series: QG-200, QG-250, QG-320, QG-400, QG-500 Odyssey Series: QG-3200, QG-4000, QG-5000, QG-6500, QG-8000 Q-Vision Series: QGV-32, QGV-40, QGV-50, QGV-65, QGV-80
SUPPLEMENTAL GENERATOR CONTROL PANEL (TechVision)
OCP2
QG-TV-C, QG-TV-F, QG-TV-IP-C, QG-TV-IP-F
TABLE
QT1
QT-730, QT-740, QT-750
TUBE SUPPORT
QS1
QS-500, QS-550
WALL STAND
QW1
QW-400, QW-420, QW-420-D, QW-420-S-L, QW-420-S-R
Revision B
1-8
Q-Rad System Quantum Medical Imaging
Chapter 1 General Information Table 1-2. Q-Rad Floor Mounted System COMPONENT X-RAY TUBE
COMPONENT DESIGNATION
COMPONENT MODEL#
TU1
TOSHIBA E7239X, E7242X, E7252X, E7254X, E7869X VARIAN RAD-14, RAD-60, RAD-92 DUNLEE DA 1092
COLLIMATOR
QC1
PROGENY MC150, Linear II, Linear IV HUESTIS 150MC (Manual)
DAP
QD1
VacuDAP–OEM Display + Ion Chamber
ION CHAMBER
IN1
AID ICX153
IMAGE RECEPTOR
RC1
Grid cabinet: MIDWEST GC-NSI Bucky cabinet: MIDWEST MWX-7440-SOM; PROGENY KLB10-08011, KLB10-08013
Q-Rad “CS Series” Ceiling-Mounted System The Q-Rad Ceiling Mounted (CS Series) system is configured around a ceiling-mounted tube support (referred to as the “overhead tube crane”). The overhead tube crane is suspended from the ceiling on a rail system providing three-axes of tube head positioning capability. Recumbent examinations are accomplished utilizing an elevating (Model QT-750) or a non-elevating (Model QT-730 and 740) radiologic table. Standing (weight-bearing) examinations are performed using upright chest stand (Model QW-420 Series). The X-ray generator is available in various power output and operator control panel types, with the typical configuration having a 80 kW output generator with an Odyssey style operator control. Table 1-3 provides model numbers of each available component in a Q-Rad Ceiling Mounted (CS Series) System. Table 1-3. Q-Rad Ceiling Mounted, CS Series COMPONENT GENERATOR
COMPONENT DESIGNATION QG1
COMPONENT MODEL# Single-Phase: QG-25-1, QG-32-1, QG-40-1 Stored Energy: QG-20-SE, QG-32-SE, QG-40-SE, QG-50-SE Three-Phase: QG-32-2, QG-32-3, QG-40-2, QG-40-3, QG-50-3, QG-65-3, QG-80-3
Q-Rad System Quantum Medical Imaging
Revision B
1-9
Chapter 1 General Information Table 1-3. Q-Rad Ceiling Mounted, CS Series COMPONENT
COMPONENT DESIGNATION
GENERATOR CONTROL PANEL
OCP1
COMPONENT MODEL# Quest Series: QG-200, QG-250, QG-320, QG-400, QG-500 Odyssey Series: QG-3200, QG-4000, QG-5000, QG-6500, QG-8000 Q-Vision Series: QGV-32, QGV-40, QGV-50, QGV-65, QGV-80
SUPPLEMENTAL GENERATOR CONTROL PANEL (TechVision)
OCP2
QG-TV-IP-C, QG-TV-IP-F
TABLE
QT1
QT-730, QT-740, QT-750
TUBE SUPPORT
QS1
RS-580 (SIEMENS 3070013)
WALL STAND
QW1
QW-400, QW-420, QW-420-D, QW-420-S-L, QW-420-S-R
X-RAY TUBE
TU1
TOSHIBA E7239X, E7242X, E7252X, E7254X, E7869X VARIAN RAD-14, RAD-60, RAD-92 DUNLEE DA 1092
COLLIMATOR
QC1
PROGENY MC150, Linear II, Linear IV HUESTIS 150MC (Manual)
DAP
QD1
VacuDAP–OEM Display + Ion Chamber
ION CHAMBER
IN1
AID ICX153, ICX 1153
IMAGE RECEPTOR
RC1
Grid cabinet: MIDWEST GC-NSI
Revision B
1-10
Bucky cabinet: MIDWEST MWX-7440-SOM, PROGENY KLB10-08011, KLB10-08013
Q-Rad System Quantum Medical Imaging
Chapter 1 General Information Intended Use The Quantum Q-Rad System provides diagnostic quality images to aid the physician with diagnosis. The system can be used to perform radiographic exposures of the skeleton (including skull, spinal column, and extremities), chest, abdomen, and other body parts. The Q-Rad Radiographic System is not indicated for use in mammography.
General Application Specification Patient Population: Age: Weight: Region of Body:
Newborn to geriatric Up to 294.8 kg (650.0 lb) Produces images of any bone in the human body, including the hand, wrist, arm, foot, ankle, knee, leg, or spine.
Operator Requirements: Education/Training:
This equipment is sold to be used exclusively under the prescribed direction of a person who is licensed by law to operate equipment of this nature.
Application: Location: Physical Environment: Frequency of Use: Mobility:
Professional use only, indoor use only. Refer to Q-Rad System operating and non-operating specifications in this chapter. Intermittent operation, limited primarily by loading characteristics specific to tube type used in the system. Stationary
Cleaning, Preventive Inspection and Maintenance Instructions for cleaning, preventive inspection and routine maintenance of Q-Rad Radiographic System, are included in each of the system component user’s and service manuals indicated in Table 1-1.
Instructions for Disposal of Waste Equipment In the European Union, this symbol indicates that when the last user wishes to discard this product, it must be sent to appropriate facilities for recovery and recycling. Contact your local representative for additional information on the collection and recovery programs available for this product.
Q-Rad System Quantum Medical Imaging
Revision B
1-11
Chapter 1 General Information Labeling Each component of the Q-Rad System has its own rating plate/serial label. The following table provides the general location of the rating plate/serial label on each of the various types of components that could be incorporated in a Q-Rad System.
Table 1-4. Q-Rad System Components Labeling Guide Component Type
Model(s)
Q-Rad System
Q-Rad
Label Location
GENERATOR CABINET
Q-RAD SYSTEM LABELS: REGULATORY LABEL
CONFIGURATION LABEL
X-ray Generator
Single-phase, non-Stored Energy QG-25, QG-25-5, QG-32, QG-32-5, QG-40, and QG-40-5 Single-phase, Stored Energy QG-20-SE, QG-32-SE, QG-40-SE, QG-50-SE
GENERATOR COMPLIANCE LABEL
Three-phase QG-32-2, QG-32-3, QG-40-2, QG-40-3, QG-50, QG-50-2, QG-65, and QG-80
Revision B
1-12
Q-Rad System Quantum Medical Imaging
Chapter 1 General Information Table 1-4. Q-Rad System Components Labeling Guide Component Type
Model(s)
TechVision Supplementary Generator Control Panel
QG-TV-F, QG-TV-IP-F, QG-TV-C, QG-TV-IP-C
Radiographic Table
Fixed Non-Float Tabletop QT-730
Label Location
compliance label
Radiographic Table
Non-Elevating Tabletop QT-740 Elevating Tabletop QT-750
Tube Support, Floor Mounted
Q-Rad System Quantum Medical Imaging
QS-500 QS-550
Revision B
1-13
Chapter 1 General Information Table 1-4. Q-Rad System Components Labeling Guide Component Type
Model(s)
Tube Support
Overhead (Ceiling) Mounted, RS-580
Radiographic Upright Cassette Holder
QW-420, QW-420-S-L, QW-420-S-R, QW-420-D QW-400
Collimator, Manual
PROGENY MC-150
Label Location
HUESTIS 150MC
Revision B
1-14
Q-Rad System Quantum Medical Imaging