Hardware Guide
56 Pages

Preview
Page 1
{MiscellaneousPUB}{Production}{Health Group}{Unrestricted}
Publication No. AA3470 2012-07-23
DRX-Ascend System Hardware Guide
© Carestream Health, Inc. 2012
Table of Contents Description
Page
Safety and Regulatory Information... 1 General Safety and Regulatory Information... 1 WARNINGS, CAUTIONS, NOTES... 1 Regulatory Compliance... 2 Intended Operator... 3 Training... 3 Instructions for Disposal of Waste Equipment... 4 Applicable Standards... 4 Safety and Regulatory Information: Generators, Tubestands, Wall Stands, and Tables 5 Classification... 5 Compatibility... 6 Guidance and Manufacturer’s Declaration-Electromagnetic Emissions... 6 Guidance and Manufacturer's Declaration-Electromagnetic Immunity... 7 Guidance and Manufacturer's Declaration-Electromagnetic Immunity... 8 Recommended Separation Distance between Portable and Mobile RF Communications Equipment and the DRX-Ascend System... 9 Additional Guidance and Manufacturer’s Declaration-Electromagnetic Emissions/ Immunity... 9 DRX-Ascend System Cables... 10 DRX-Ascend System Component Power Disconnection Methods... 11 General Information... 12 Overview of the DRX-Ascend System... 12 DRX-Ascend System Components Overview... 13 Operator Console... 13 Power/Expose Control Box... 14 Power Failures... 14 Generators... 15 Generator Key Features... 15 Generator Electric Output Data... 16 Main Generator Components... 17 Generator Controls and Indicators... 17 Tubestand... 17 Main Components-Model QS-550 Tubestand... 19 Model QW-420 Wall Stand... 20 Wall Stand Intended Use... 20 Main Components-Model QW-420 Wall Stand... 21 Fixed and Elevating Radiographic Tables... 22 Fixed and Elevating Radiographic Tables Intended Use... 22 Radiographic Tables Receptor Options... 23 Radiographic Table Main Components... 23 DRX-Ascend System Components Operation... 24 Operator Console Operation... 24 Power On and Off Procedures... 24 Daily Tube Warm-up Procedure... 25 Generator Fault Messages... 26 Tubestand Operation... 29 Manual Motions and Detents-Model QS-500... 29 Manual Motions and Detents-Model QS-550... 30 Handgrip Controls and Indicators... 31 Collimator Controls... 34 Wall Stand Operation... 35 Receptor Control Handle Operation... 35 Optional Patient Overhead Grip Operation... 36 Detector Housing Operation... 37 AA3470 – 2012-07-23
i
Fixed and Elevating Radiographic Tables Operation... Tabletop Float Motion (All Models)... Foot Pedal Disable Switch (All Models)... Elevating Motion (Model QT-750 Only)... Lowering the Tabletop... Raising the Tabletop... Image Receptor Cabinet Lock... Loading Detectors Into Trays-Wall Stand and Tables... User Maintenance... DRX-Ascend Periodic Maintenance Schedule... Labelling... Specifications... Generator Performance Specifications... System Operating Environment... Non-Operating Environment... Physical Specifications... Tubestand... Heat Dissipation... System Accessories... System Operating Environment... Transport and Non-Operating Environment... Publication History...
ii
39 40 41 42 43 43 43 44 45 45 46 47 47 48 48 48 48 49 50 50 50 51
2012-07-23 – AA3470
Safety and Regulatory Information
Section 1: Safety and Regulatory Information General Safety and Regulatory Information Carestream Health, Inc. products are designed to meet stringent safety standards. All medical electrical equipment requires proper installation, operation, and maintenance (particularly with regard to safety). It is vital that the user read, understand, note, and where applicable, strictly observe all Warnings, Cautions, Notes, and Safety markings within this document and on the equipment. The user should strictly follow all safety directions in this manual to help ensure the safety of users and patients. Every reasonable precaution has been taken during manufacture to safeguard the health and safety of persons who will operate this equipment. The following precautions must be observed at all times.
WARNINGS, CAUTIONS, NOTES The following samples show how warnings, cautions, and notes appear in this document. The text explains their intended use.
W WARNING Indicates injury or death is possible if the instructions are not obeyed. Instructs users to refer to documentation if displayed without warning text.
CAUTION Indicates that damage to equipment is possible if the instructions are not obeyed.
NOTE Provides advice and highlights unusual points. A note is not intended as an instruction. The purpose of safety icons, such as those shown below, is to indicate at a glance the type of caution, warning, or danger.
WARNING Ionizing radiation: indicates the possibility of increased levels of radiation.
WARNING Warning, hot surface.
WARNING Dangerous voltage; indicates the presence of high voltage.
AA3470 – 2012-07-23
1
Safety and Regulatory Information
WARNING X-rays are hazardous to both patients and operators unless established safe exposure factors and operating instructions are observed. Only qualified and authorized personnel shall operate this system. In this context, qualified means those legally permitted to operate this equipment in the jurisdiction in which the equipment is being used, and authorized means those authorized by the authority controlling the use of the equipment. Full use must be made of all radiation protection features, devices, systems, procedures and accessories. It is important that everyone having anything to do with x-radiation be properly trained and fully acquainted with the recommendations of the National Council on Radiation Protection and Measurements as published in NCRP Reports available from NCRP Publications, 7910 Woodmont Avenue, Suite 800, Bethesda, Maryland 20814-3095 (www.ncrp.com), and of the International Commission on Radiological Protection (www.icrp.org), and take adequate steps to protect against injury.
W WARNING Carestream Health, Inc. disclaims all responsibility from any injury resulting from improper application of this equipment. This equipment is sold to be used exclusively under the prescribed direction of a person who is licensed by law to operate equipment of this nature. This equipment must be used in accordance with all safety procedures described in this manual and must not be used for purposes other than those described herein. Carestream Health cannot assume responsibility for any malfunctioning of this equipment resulting from improper operation, maintenance, or repair, or from damage or modification of its components. Failure to observe these warnings may cause serious injuries.
W WARNING X-ray equipment may cause injury if used improperly. The instructions contained in this manual must be read and followed when operating this unit. Personal radiation monitoring and protective devices are available. You are urged to use them to protect against unnecessary X-ray exposure.
Operator Safety Notice Regulations require that the Operator of this equipment remain within visual range of all exposure indicator icons displayed on the Operator’s screen during all phases of each exposure cycle. Furthermore, the Operator must remain within the audible range of the audible alarm generated during exposure cycles. Accordingly, the Power/Expose Control Box must be securely mounted as to comply with the foregoing.
Regulatory Compliance This medical device has been designed, manufactured, and calibrated to comply with governing U.S. Federal Regulations 21 CFR, Subchapter J and the performance standards attendant thereto. Upon installation, all certified products require the filing of Form FD-2579 "Report of Assembly of a Diagnostic X-ray System" by the assembler (the installer) with the appropriate agencies. The "Installation Quality Assurance Checklist" must also be completed and properly distributed upon installation. A copy of each form (pink copy) is provided to the user. Those responsible for the planning of X-ray equipment installations must be thoroughly familiar and comply completely with NCRP Report No. 49, "Structural Shielding Design and Evaluation for Medical Use of X-Rays and Gamma Rays of Energies up to 10 MeV," as revised or replaced in the future. Those authorized to operate, test, participate in, or supervise the operation of the equipment must be thoroughly familiar and comply completely with the currently established safe exposure factors and procedures described in publications such as Subchapter J of Title 21 of the Code of Federal Regulations, "Diagnostic X-Ray Systems and Their Major Components," and NCRP Report No. 102, “Medical X-Ray, Electron Beam and Gamma Ray Protection for Energies Up to 50 MeV-Equipment Design and Use” as revised or replaced in the future. Scheduled maintenance is essential to the assurance of continued integrity of this equipment with respect to regulatory compliance. The continuance of certified performance to the regulatory standard is incumbent upon the user's diligent conformance to recommended maintenance instructions.
AA3470 – 2012-07-23
2
Safety and Regulatory Information
Associated Documents Refer to the CARESTREAM DRX-1 Digital Radiography System documentation set for instructions regarding the use of all DRX-1 system components and software.
Intended Operator This equipment is intended to be installed, used, and operated only in accordance with the safety procedures given within this manual for the purpose for which it was designed. Before attempting to work with this equipment, read, understand, note, and strictly observe all warnings, cautions, and safety markings on the equipment. Users include those persons who actually handle the equipment and those who have authority over the equipment.
Training Users of this equipment shall have received adequate training on its safe and effective use before attempting to work with the equipment. Training requirements may vary from country to country. The user shall make sure that training is received in accordance with local laws or regulations that have the force of law.
Patient Environment The following components of the DRX-Ascend System are NOT permitted inside the patient environment: • X-ray generator (including operator control panel-All Models) • DRX-1 Workstation Computer When the generator is configured with the DRX-Ascend Operator Console, the associated workstation computer functions as the generator Operator Control Panel (OCP). If the workstation is qualified to standard UL 60950/ IEC 60950 for Information Technology Equipment, the workstation must be placed outside the radius of the patient environment, as shown below. Consult with the user of the system when determining the location for the workstation computer. Consider all areas the patient may access, including the room entrance and/or exit, when establishing the patient environment.
2.5 m (8.2 ft)
1.5 m (4.9 ft)
AA3470 – 2012-07-23
(4.9 ft)
1.5 m (4.9 ft)
3
Safety and Regulatory Information
Instructions for Disposal of Waste Equipment
In the European Union, this symbol indicates that when the last user wishes to discard this product, it must be sent to appropriate facilities for recovery and recycling. Contact your local representative for additional information on the collection and recovery programs available for this product.
Applicable Standards This equipment complies with the following regulatory standards: • EN 60601-1:1990 + A1:1993 + A2:1995 + A13:1996 • CAN/CSA-C22.2 No. 601.1-M90, 2005 (Medical Electrical Equipment, Part 1: General Requirements for Safety) • UL 60601-1, 1st Edition, 2006-04-26 (Medical Electrical Equipment, Part 1: General Requirements for Safety) • IEC 60601-1 (Medical Electrical Equipment, Part 1: General Requirements for Safety) • IEC 60601-1-2:2007 • IEC 60601-2-32:1994 • IEC 60601-2-7:1998(E) EU Authorized Representative:
Carestream Health France 1, rue Galilée 93192 NOISY-LE-GRAND CEDEX FRANCE
AA3470 – 2012-07-23
4
Safety and Regulatory Information
Safety and Regulatory Information: Generators, Tubestands, Wall Stands, and Tables Classification This product has been classified as Class I, Type B. This equipment is not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or with nitrous oxide. Protection against Harmful Ingress of Water (Ordinary), enclosed equipment without protection against ingress of liquids.
MEDICAL ELECTRICAL EQUIPMENT WITH RESPECT TO ELECTRIC SHOCK, FIRE, MECHANICAL HAZARDS ONLY CONFORMS TO UL STD 60601-1 CERTIFIED TO CAN/CSA STD C22.2 NO. 601.1
MEDICAL ELECTRICAL EQUIPMENT WITH RESPECT TO ELECTRIC SHOCK, FIRE, MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL 60601-1 AND CAN/CSA C22.2 NO. 601.1 98UA
The following symbols and acronyms may be used for marking on this equipment or equipment documentation. Earth
Dangerous Voltage
Protective Earth (ground)
Attention (consult operating instructions)
Type B Equipment
Enable Longitudinal Tube Motion
Enable Tube Angulation Motion
Enable Vertical Tube Motion
Enable Rotation of Vertical Column Motion
Enable Transverse Tube Motion
Enable Auto-Stop Function
Non-ionizing Radiation
Enable Tube Motion in all Directions
Connection Point for the Neutral Conductor on Permanently Installed Equipment
Enable Tabletop Float (releases transverse and longitudinal locks)
Enable Tabletop Up Motion
Alternating Current
Enable Tabletop Down Motion
AA3470 – 2012-07-23
5
Safety and Regulatory Information
Abbreviation
Definition
CCW
Counterclockwise
CW
Clockwise
cm
Centimeters
GHz
Gigahertz
in.
Inches
MHz
Megahertz
mm
Millimeters
SAE
Society of Automotive Engineers
SID
Source-to-image distance
W
Watts
Compatibility The equipment described in this manual must only be used in combination with other equipment or components, if these are expressly recognized by Carestream Health, Inc. as compatible.
Guidance and Manufacturer’s Declaration-Electromagnetic Emissions The DRX-Ascend System (including TechVision option) is intended for use in the electromagnetic environment specified below. The customer or the user of the DRX-Ascend System should ensure that it is used in such an environment. Emissions Test
Compliance
Electromagnetic Environment Guidance
RF emissions CISPR 11
Group 1
The DRX-Ascend System uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
RF emissions CISPR 11
Class A
The DRX-Ascend System is suitable for use in all establishments other than domestic and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Harmonics emissions IEC 61000-3-2
Class A
Voltage fluctuations/ flicker emissions IEC 61000-3-3
Complies
The Harmonics and Voltage Fluctuations compliance status applies to all System AC powered components except the vertical wall stand and the floor-to-ceiling/wall and free-standing tubestands. The wall stand and tubestand are not connected to the public low-voltage power supply network.
AA3470 – 2012-07-23
6
Safety and Regulatory Information
Guidance and Manufacturer's Declaration-Electromagnetic Immunity The DRX-Ascend System (including TechVision option) is intended for use in the electromagnetic environment specified below. The customer or the user of the DRX-Ascend System should ensure that it is used in such an environment. Immunity Test
IEC 60601 Test Level
Compliance Level
Electromagnetic Environment Guidance
Electrostatic discharge (ESD) IEC 61000-4-2
± 6 kV contact
± 6 kV contact
± 8 kV air
± 8 kV air
Floors should be wood, concrete, or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30 %.
Electrical fast transient/burst IEC 61000-4-4
± 2 kV for power supply ±2 kV for power supply lines lines ± 1 kV for input/output lines
± 1 kV for input/ output lines
Surge IEC 61000-4-5
± 1 kV line to line
± 1 kV line to line
± 2 kV line to earth
± 2 kV line to earth
Mains power quality should be that of a typical commercial or hospital environment.
Mains power quality should be that of a typical commercial or hospital environment. The surge status applies to all system AC powered components except the vertical wall stand, the floor-to-ceiling/wall and freestanding tubestands. The wall stand and tubestand are not connected to the public low-voltage power supply network.
Voltage dips, short interruptions, and voltage variations on power supply lines IEC 61000-4-11
Power frequency (50/60 Hz) magnetic field IEC 61000-4-8
< 5 % UT (> 95 % dip in UT) for 0.5 cycle
< 5 % UT (> 95 % dip in UT) for 0.5 cycle
40 % UT (60 % dip in UT) for 5 cycles
40 % UT (60 % dip in UT) for 5 cycles
70 % UT (30 % dip in UT) for 25 cycles
70 % UT (30 % dip in UT) for 25 cycles
< 5 % UT (> 95 % dip in UT) for 5 sec.
< 5 % UT (> 95 % dip in UT) for 5 sec.
3 A/m
3 A/m
Mains power quality should be that of a typical commercial or hospital environment. The voltage dips and short interruptions compliance status applies to all system AC powered components except the vertical wall stand, the floor-to-ceiling/wall and freestanding tubestands. The wall stand and tubestand are not connected to the public low-voltage power supply network.
Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.
NOTE: UT is the a.c. mains voltage prior to application of the test level.
AA3470 – 2012-07-23
7
Safety and Regulatory Information
Guidance and Manufacturer's Declaration-Electromagnetic Immunity The DRX-Ascend System (including TechVision option) is intended for use in the electromagnetic environment specified below. The customer or the user of the DRX-Ascend System should ensure that it is used in such an environment. Immunity Test
IEC 60601 Test Level
Compliance Level
Electromagnetic Environment Guidance Portable and mobile RF communications equipment should be used no closer to any part of the DRX-Ascend System, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.
Conducted RF IEC 61000-4-6
3 Vrms 150 kHz to 80 MHz
Radiated RF IEC 61000-4-3
3 v/m 80.0 MHz to 2.5 GHz
3 Vrms 3 v/m
Recommended separation distance: d = 1.17 √ P (Tethered configuration only) d = 1.17 √ P 80 MHz to 800.0 MHz d = 2.33 √ P 800 MHz to 2.5 GHz where P is the maximum output rating of the transmitter in watts (W) according to the transmitter manufacture and d is the recommended separation distance in meters (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site surveya, should be less than the compliance level in each frequency rangeb. Interference may occur in the vicinity of equipment marked with the following symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people. a Field strengths from fixed transmitters, such as base station for radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast, and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the DRX-Ascend System is used exceeds the applicable RF compliance level shown above, the System should be observed to normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the detector. b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 v/m.
AA3470 – 2012-07-23
8
Safety and Regulatory Information
Recommended Separation Distance between Portable and Mobile RF Communications Equipment and the DRX-Ascend System The DRX-Ascend System (including TechVision option) is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the DRX-Ascend System can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communication equipment (transmitters) and the DRX-Ascend System as recommended below, according to the maximum output of the communications equipment. Rated maximum output power of transmitter (W)
Separation distance according to frequency of transmitter (meters) 150.0 kHz to 80.0 MHz d = 1.17 √ P
80.0 MHz to 800.0 MHz d = 1.17 √ P
800.0 MHz to 2.5 GHzn d = 2.33 √ P
0.010
0.117
0.117
0.233
0.100
0.370
0.370
0.737
1.000
1.170
1.170
2.330
10.000
3.700
3.700
7.360
100.000
11.700
11.700
23.300
Additional Guidance and Manufacturer’s Declaration-Electromagnetic Emissions/Immunity Electromagnetic Compatibility Precautions Medical electrical equipment requires special precautions regarding electromagnetic compatibility (EMC). Medical equipment must be installed and put into service according to the EMC information provided in the following documentation.
Communications Equipment Portable and mobile radio frequency (RF) communications equipment can affect medical electrical equipment EMC performance. The wireless version of the CARESTREAM DRX-1 System Detector operates with the 802.11n protocol in the 5 GHz frequency band. The radio output power is 20 dBm (nominal).
WARNING Other equipment can interfere with communications with the CARESTREAM DRX-1 System Detector even if that other equipment complies with CISPR emissions requirements.
Replacement of Cables, Accessories, or Transducers The use of cables, accessories, or transducers other than those specified below, with the exception of transducers or cables sold by the manufacturer of the equipment as replacement parts for internal components, may result in increased emissions or decreased immunity of the medical equipment.
Other Equipment The DRX-Ascend System should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is necessary, the DRX-Ascend System should be observed to verify normal operation in the configuration in which it will be used.
Shielded Locations The DRX-Ascend System must be used in a shielded room for personal safety only. The DRX-Ascend System is fully compliant with the requirements of IEC 60601-1-2:2004 without being located in a shielded room.
AA3470 – 2012-07-23
9
Safety and Regulatory Information
DRX-Ascend System Cables
System Component
EUT Port
Cable Length (ft)
Signal Description
Cable Description
Routed to/Port
DAP Display QD1
DC Input
6.4
AC Power Input
Unshielded, 15 V (dc) AC mains power
DAP
Data/Power
80
Data
Unshielded, RS-485, DC power
Collimator power supply
AC Input
6
24 V (ac)
Unshielded AC mains Generator AC mains
Generator QG-1
A1, A1, P3
80
24 V (ac)
HV cable
Generator QG-1
A1, A1, P3
80
Communication Data Shielded, multiconductor
PC computer station of digitizer
Data
100
Data
Shielded, Gen control Generator QG-1/ A1, P5
PC computer station of digitizer
Ethernet
100
Data
Shielded, CAT5
Generator QG-1/ A1, P1
Generator QG-1/TB-1 AC Input
30
AC Power Input
Unshielded, 4 conductor
AC mains
DAP display QD1
Collimator Collimator
Generator QG-1
A17, A
80
Anode HV Cable (+)
Shielded, HV cable
X-ray tube
Generator QG-1
A17, C
80
Anode HV Cable (–)
Shielded, HV cable
X-ray tube
Generator QG-1
A20 A2, TB1, 80 and TB4
Rotor Cable
Shielded, rotor drive cable
X-ray tube
Generator QG-1
A11, P3
65
Analog/Digital Signals
Shielded, AEC signals AEC Ion Chamber option / J1 in table QT-750
Generator QG-1
A11, P2
65
Analog/Digital Signals
Shielded, AEC signals Wall stand AEC Ion Chamber option / J1
Generator QG-1
A9, TB2
65
Analog/Digital Signals
Unshielded, multiconductor
Wall stand receptor housing
Ethernet Switch
N/A
100
Ethernet
Shielded, Ethernet
TechVision
Generator QG-1
A1, J3
100
TechVision Power (24/28 V)
Shielded, 2 conductor TechVision
Generator QG-1
A9, TB3, TB4 100
Low Power
9-pin connector
Interface box
Generator QG-1
+28 V (dc) 80 power supply
QS1 Power
Unshielded, 2 conductor
QS1
Stationary Digital Receptor
QB1 DR Receptor holder
85
Receptor Handshake Unshielded, multiconductor
Generator QG-1/ A9, TB3
PC computer station of digitizer
Ethernet
100
Data
Shielded, CAT5
4343R Digital receptor
Generator QG-1
A9, A1, TB1
100
Data
Shielded, multiconductor
Wall 4343R Digital receptor
Generator QG-1
A11, P2
100
Data
Shielded, multiconductor
Wall J1, AEC Ion chamber
Generator QG-1
A11, P3
100
Data
Shielded, multiconductor
Table J1, AEC Ion chamber
AA3470 – 2012-07-23
10
Safety and Regulatory Information
DRX-Ascend System Component Power Disconnection Methods Component Type
Model
Means of Power Disconnect
X-ray Generator, Single-phase, non-Stored Energy
QG-40-1
ON/OFF circuit breaker CB1 on generator cabinet
X-ray Generator, Single-phase, Stored Energy
QG-40-SE, QG-50-SE
ON/OFF circuit breaker CB1 on generator cabinet
X-ray Generator, Three-phase
QG-40-2, QG-40-3, QG-50-2, QG50-3, QG-65, and QG-80
ON/OFF circuit breaker CB1 on generator cabinet
TECHVISION Supplementary Generator Control Panel
QG-TV-IP-F, QG-TV-IP-C
ON/OFF circuit breaker CB1 on generator cabinet
Radiographic Table, Non-Elevating Tabletop
QT-740
Unplug Line Cord
Radiographic Table, Elevating Tabletop
QT-750
Unplug Line Cord
Tube Support, Floor/Wall Mounted
QS-500
ON/OFF circuit breaker CB1 on generator cabinet
Tube Support, Free-Standing (Floor) Mounted
QS-550
ON/OFF circuit breaker CB1 on generator cabinet
Collimator, Manual
PROGENY, MC150 PROGENY, MC150 PINNACLE
ON/OFF circuit breaker CB1 on generator cabinet
Collimator, Automatic
HUESTIS Programmable, CM32211-QMI
Unplug Line Cord (ACS Power Supply and Junction Box)
X-ray tube
TOSHIBA E7252X, E7254X, VARIAN ON/OFF circuit breaker RAD-60, RAD-92, Dunlee DA 1092, CB1 on generator cabinet DA1036
Dose Area Product Meter (optional) VACUTEC Display Unit: VACUDAP OEM (QD1-2) VACUTEC Ion Chamber: VACUDAP OEM (QD1-1
Unplug Line Cord
CARESTREAM Digital Imaging System
Quick Reference Card for the CARESTREAM DRX-1 System, PN 8G8318 Carestream DRX-1 System Safety and Regulatory Information with Hardware User's Guide, PN 9J1967 CARESTREAM DRX-1 System Battery Charger User's Guide, PN 8H6193
AA3470 – 2012-07-23
DRX-1
11
General Information
Section 2: General Information Overview of the DRX-Ascend System NOTE The user should read this manual in its entirety prior to using this equipment. This manual should be kept in a location near the equipment and be readily accessible to those who operate it. This document is intended to assist users in the safe and effective operation of the equipment described herein. Pay special attention to all the information described in the Safety section (refer to “Safety and Regulatory Information” on Page 1). It is imperative that all safety procedures described in this manual be strictly adhered to in order to ensure the safety of both patient and user. When the QG-DIG-DRX Integration Software is installed, all user interaction with the HF Series X-ray Generator is accomplished via the Workstation’s touch screen, thereby eliminating the need for a separate Operator Control Panel for the generator. In addition, the optional TechVision Control Panel can be installed and synchronized with the DRX Workstation to optimize operator efficiency.
NOTE TechVision is a functional operator interface control panel providing access to generator controls and visual presentation of the exposures taken in the current study. TechVision is designed for installation in the patient area, and has full programming/editing capability, but it cannot activate an exposure. Once the patient is registered in the DRX System environment and the appropriate body part examination procedure is selected, the generator control parameters are uploaded prior to performing the exposure. The QUANTUM QG-DIG-DRX Integration System technology is available for DRX Series digital detectors, in applications where a QUANTUM Q-Rad System, including an HF Series X-ray Generator is installed. The QG-DIGDRX System software resides on the DRX Workstation Computer hard disk and is automatically loaded whenever the Workstation Computer is powered-up. Combining the image acquisition capacity of the DRX digital detectors with QG-DIG-DRX System software, controlling an HF Series X-ray Generator, work lists compiled from stored patient profiles, or those manually entered, are displayed for immediate disposition in the DRX operating environment. Operation of the QG-DIG-DRX Integration System software is accomplished through a touch-sensitive operator control panel screen, integrated with the DRX System Workstation screen. Once the DRX Software is installed and a Service Technician has completed the system and generator setup, it is not necessary for the operator to access and adjust the Service Options.
W WARNING The DRX System screen should display four generator parameters (kV, mA, ms, and mAs) at all times. If any one of these parameters is not displayed, contact Technical Service.
AA3470 – 2012-07-23
12
DRX-Ascend System Components Overview
Section 3: DRX-Ascend System Components Overview Operator Console Refer to the DRX-Ascend System Software User’s Guide, PN AA3471 for information regarding the Operator Console.
AA3470 – 2012-07-23
13
DRX-Ascend System Components Overview
Power/Expose Control Box 1. Prep/Expose Button 2. Power/Expose Control Box 3. Rocker Switch 4. On/Off LED
CAUTION The Power/Expose Control box must be positioned as to allow the operator to clearly view the Operator Console and hear the audible alarm during the exposure cycle.
Power Failures There are various types of power disruptions that can affect a System: voltage sags, voltage surges, brownouts, line noise, high voltage spikes, frequency variations, switching transients, and harmonic distortions. These disruptions can be corrected by a Uninterruptible Power Supply (UPS). The DRX-Ascend System does not come with a UPS. A UPS provides back-up power in the event of a power failure. A UPS also conditions the power provided to the System. Back-up power will last for a specific length of time, dependent on the UPS energy storage capacity and the power requirements of the equipment. If you choose to provide a UPS for your System, follow the manufacturer's recommendation for use and battery replacement. A UPS can be used to power the DRX-Ascend Operator's Console. If the DRX-Ascend System is also configured with a fixed 43x43 detector then both the Operator's Console and the power supply for the 43x43 detector should be powered from the UPS. For UPS specifications see “CARESTREAM DRX-1 System Safety and Regulatory Information with Hardware User's Guide" PN 9J1967.
AA3470 – 2012-07-23
14
DRX-Ascend System Components Overview
Generators The HF Series X-ray Generators include the following models: • Model QG-40-1: 40k W, 208–240 V (ac) single-phase input configuration • Model QG--40-2: 40 kW, 208–240 V (ac) three-phase input configuration • Model QG--40-3: 40 kW, 380–480 V (ac) three-phase input configuration • Model QG--40-SE: 40 kW, stored energy (SE) 115/230 V (ac) single-phase input configuration • Model QG-50-SE: 50 kW, stored energy (SE) 115/230 V (ac) single-phase input configuration • Model QG-50-3: 50 kW, 380–480 V (ac) three-phase input configuration • Model QG-50-2: 50 kW, 208–240 V (ac) three-phase input configuration • Model QG-65: 65 kW, 380–480 V (ac) three-phase input configuration • Model QG-80: 80 kW, 380–480 V (ac) three-phase input configuration
Generator Key Features It is imperative that all safety procedures described in this manual be strictly adhered to in order to ensure the safety of both patient and user. The key features of the HF Series X-ray Generators are as follows: • Ultra high-frequency (up to 120 kHz) voltage waveform for highly efficient X-ray production • Manual, AEC (optional), and automatic (APR) modes of operation • Anatomic Programmability (APR) pre-defined and customized technique selection • Wall/Table/None image receptor selection • Compact generator cabinet design • Multi-language display capability
Generator Intended Use The HF Series X-ray Generators are diagnostic X-ray high-voltage generators. They are intended to supply and control the electrical energy applied to a diagnostic X-ray tube for medical radiographic examinations.
AA3470 – 2012-07-23
15
DRX-Ascend System Components Overview
Generator Electric Output Data Output Parameter
Model
Nominal X-ray tube voltage and QG-40-1, QG-40-2, QG-40-3 highest X-ray tube current obtainable at that voltage QG-40-SE
Maximum X-ray tube current and highest X-ray tube voltage obtainable at that current
Loading Factor 125 kV, 320 mA (150 kV, 250 mA with QG-150 option) 125 kV, 320 mA
QG-50-3, QG-50-2
125 kV, 400 mA (150 kV, 320 mA with QG-150 option)
QG-50-SE
125 kV, 400 mA
QG-65
150 kV, 400 mA
QG-80
150 kV, 500 mA
QG-40-1, QG-40-2, QG-40-3
500 mA, 80 kV
QG-40-SE
500 mA, 80 kV
QG-50-3, QG-50-2
650 mA, 76 kV
QG-50-SE
600 mA, 83 kV
QG-65
800 mA, 81 kV
QG-80
800 mA, 100 kV
QG-40-1, QG-40-2, QG-40-3
400 mA, 100 kV 500 mA, 80 kV
QG-40-SE
320 mA, 125 kV 400 mA, 100 kV 500 mA, 83 kV
QG-50-3, QG-50-2
400 mA, 125 kV 500 mA, 100 kV 650 mA, 76 kV
QG-50-SE
400 mA, 125 kV 500 mA, 100 kV 600 mA, 83 kV
QG-65
500 mA, 130 kV 650 mA, 123 kV 800 mA, 81 kV
QG-80
650 mA, 123 kV 800 mA, 100 kV
QG-40-1, QG-40-2, QG-40-3
40 kW (400 mA, 100 kV, 0.1 s)
QG-40-SE
40 kW (400 mA, 100 kV, 0.1 s)
QG-50-3, QG-50-2
50 kW (500 mA, 100 kV, 0.1 s)
QG-50-SE
50 kW (500 mA, 100 kV, 0.1 s)
QG-65
65 kW (650 mA, 100 kV, 0.1 s)
QG-80
80 kW (800 mA, 100 kV, 0.1 s)
Nominal shortest irradiation time (AEC exposures)
All models
0.008 seconds
Lowest mAs
All models
0.025 mAs (25.000 mA, 1.000 mA)
Combination of X-ray tube current and X-ray tube voltage resulting in highest output power (Note: All mA stations below those listed can go to maximum voltage)
Highest constant output power at 100 kV, 0.1 second (s)
AA3470 – 2012-07-23
16
DRX-Ascend System Components Overview
Main Generator Components The HF Series X-ray Generator comprises the generator cabinet, which contains the electronics for high voltage generation and control.
Generator Controls and Indicators See the following figure for the location of the generator power on/off switch.
Tubestand Key features of the Model QS-500 Tubestand and QS-550 Tubestand: • Vertical travel 153.7 cm (60.5 in.), longitudinal travel 243.8 cm (96.0 in.) using a 3 m (10 ft) floor track • Fail-safe electromagnetic lock for vertical tubestand motion • Electromagnetic locks for longitudinal and angulation tubestand motions • 102 cm (40 in.) and 183 cm (72 in.) SID indicators on the handgrips and vertical column 102 cm (40 in.) and Floor Track 183 cm (72 in.) • Tube/Collimator positioning handgrips provide lock release buttons for quick tube positioning • As low as 33 cm (13 in.) focal spot-to-floor distance • Model QS-500 Tubestands equipped with QS-50R option: permits ± 90 ° vertical column rotation • Model QS-550 Tubestands equipped with TechVision handgrip option: TechVision replaces the standard equipment handgrips to provide tubestand position controls and indicators, and serves as a generator remote control panel. Refer to the TechVision Remote Control Panel Service Manual, and DRX-Ascend System Software Guide for complete installation and operation instructions.
AA3470 – 2012-07-23
17