MS 3200 User Manual April 2016

TABLE OF CONTENTS PREFACE ... 2 GENERAL INFORMATION ... 2 SAFETY INSTRUCTION ... 2 ENVIROMENTAL ... 3 CLEANING... 3 MAINTENANCE ... 3 WEIGHING OPERATION ... 3 WARRANTY-LIABILITY... 4 DISPOSING OF THE SCALE ... 4 SPECIFICATIONS ... 5 KEY FUNCTIONS ... 6 LCD DISPLAY ... 7 INSTRUCTION FOR REPLACING BATTERY... 8 ERROR MESSAGE... 10

ERROR MESSAGE

Low Battery

If battery is running out of power, the display shows

. You should replace the battery.

Over Load

If the total load exceeds the maximum capacity of scale, the display shows “Err”. The weight must be removed from the platform.

Over Zero

If zero count is higher than the setting range, the display shows “Err”. The scale will turn off if the status lasts 30 seconds.

Under Zero If zero count is below the setting, the display shows “Errl”. The scale will turn off if the status lasts 30 seconds.

1

10

STEP.3

PREFACE Thank you for choosing CHARDER MEDICAL product. All features of this product were designed to state of the art and are optimized for simple and straightforward use. If you have any queries or experience any problems not addressed in the operating instructions, please contact your CHARDER MEDICAL

service

partner,

or

visit

us

on

the

Internet

at

www.chardermedical.com

GENERAL INFORMATION We strongly recommend you use the scales on flat and hard surface. Any soft surface, like carpet will cause inaccuracy.

SAFETY INSTRUCTION Before putting the device into use, please read with care the

SETP.4

information given in the Operating Instructions. They contain important instructions for installation, proper use and maintenance of the device. The manufacturer shall not be liable for damages arising out of failure to heed the following instructions:  When using electrical components under increased safety requirements, always comply with the appropriate regulations.  Improper installation will render the warranty null and void.  Ensure the voltage marked on the power supply unit matches your mains power supply.  This device is designed for use indoors.  Observe the permissible ambient temperatures for use  The device meets the requirements for electromagnetic compatibility. Do not exceed the maximum values specified in the applicable standards.

If you have any problem, contact your local CHARDER MEDICAL service partner. 9

2

ENVIROMENTAL

INSTRUCTION FOR REPLACING BATTERY

 All batteries contain toxic compounds; disposal of batteries should be

STEP.1

delegated to a competent organisation, complying with the deposit of Poisonous Waste Regulation 1972.  Please do not incinerate batteries.  The optimum operating temperature for the scale is 5℃ to +35℃; although it will operate at higher and lower temperatures the scales battery life will be adversely effected.

CLEANING  We would recommend using alcohol based wipes or similar when cleaning the scales.  Please do not use large amounts of water when cleaning the scales as this will cause damage to the scales electronics, you should also refrain from using corrosive liquids or high pressure washers.  Always disconnect the scales from the mains power supply before cleaning.

STEP.2

MAINTENANCE  The scale does not require any routine maintenance. However, we recommend checking the scale’s accuracy at regular intervals. The regularity of these checks is dependent on the level of use and the state of the scale. If any inaccuracies occur, please contact your local dealer or CHARDER MEDICAL service partner.

WEIGHING OPERATION  Before reading detailed instructions on how to use all the weighing functions that are built into your scale, please read the following important guidelines:

Always be sure that the display shows `Zero` before use, if it does not then please press the ZERO key

3

8

 The Device is designed to detect when a stable weight is achieved, the

LCD DISPLAY

indicator will `bleep` twice to indicate a stable weight value, your reading

Symbol 

 kg , lb or oz Lo-bAt

Description

should be taken at this point.

True zero

WARRANTY-LIABILITY

Stable signal

 If a fault or defect is present on receipt of the unit which is within CHARDER

Current weighing unit

MEDICAL’s scope of responsibility, CHARDER shall have the right to either

Running out of battery and will auto shut-off 5 min later.

repair the fault or supply a replacement unit. Replaced parts shall be the property of CHARDER. Should the fault repairs or replacement delivery not

Indicate the Net Weight (NW) or the Gross Weight (GW)

be successful, the statutory provisions shall be valid. The period of warranty shall be two years, beginning on the date of purchase. Please retain your receipt as proof of purchase. Should your scale require servicing, please contact your dealer or CHARDER MEDICAL Customer Service.  No responsibility shall be accepted for damage caused through any of the following reasons: Unsuitable or improper storage or use, incorrect installation or commissioning by the owner or third parties, natural wear, changes or modifications, incorrect or negligent handling , overuse, chemical, electrochemical or electrical interference or humidity, unless this is attributable to negligence on the part of CHARDER MEDICAL.  If operating, climatic or any other influences lead to a major change in conditions or material quality, the treaty for perfect unit functioning shall be rendered null and void. If CHARDER provides and individual warranty, this means that the unit supplied will be free of faults for the length of the warranty period.

DISPOSING OF THE SCALE  This product is not to be treated as regular household waste, but should be handed in to an electrical/electronic equipment recycling centre.  You can obtain further details from your local council, your municipal waste disposal company or the firm which you purchased the product. 7

4

SPECIFICATIONS Model

KEY FUNCTIONS

MS 3200

KEY DESCRIPTION

Maximum Capacity

300 kg / 660 lbs.

Graduation

0.1 kg / 0.2 lb

Accuracy

±300g

Tare Range

Full range

Units of Measure

Kg/lb

Stabilisation Time

1-2 sec.

Operating Temperature

5 ° C – 35 ° C or 13 ° F – 95 ° F

Power supply

9V- 12V battery or AC adaptor

Calibration

Automatic External

Calibration mass

300 kg

Indicator display

1.0” LCD digital display

Dimensions (w x d x h)

15.5x12.5x3.3 inch

Gross Weight

7.7 lb / 3.5 Kg

Tare On / Zero / Off Units Hold

- Tare the weight of container previously so that the operator can get the weight of subjects only - Press to power on , zero or off, - Select kilograms, pounds or ounces - Temporarily memory the weight. Place an item to be weighed on the platform. Press HOLD key, the arrow of the left bottom will blink. The display shows the measured weight. After removing the object, the display still shows the weight. Press HOLD or TARE button to disable HOLD function.

INSTRUCTION FOR TARE FUNCTION 1) Press On/Zero/Off key to power on. 2) When zero is displayed on LCD, place an empty container on the platform and it shows the weight of container. 3) Press tare key to tare the weight of container and get zero value. 4) Place anything for weighing in the empty container and then you will get the weight of subject only.

5

6