LLS-050 LED Light Source Operator Manual Rev. C June 2014

TABLE OF CONTENTS 1. 2.

INTRODUCTION 1.1 INDICATIONS FOR USE WARNINGS

3.

SPECIFICATIONS

4.

OPERATING ELEMENTS, SYMBOLS AND FUNCTIONS 4.1 FRONT PANEL 4.2 REAR PANEL 4.3 BOTTOM PANEL

5.

INSTALLATION 5.1 SETTING UP LIGHT SOURCE 5.2 CONNECTING LIGHT CABLE

6.

OPERATION 6.1 POWERING UP LIGHT SOURCE 6.2 LIGHT BRIGHTNESS CONTROL

7.

CLEANING

8.

DISINFECTION 8.1 DISINFECTING UNIT

9.

SERVICING & REPAIR FUSE REPLACEMENT 9.1

10.

END OF PRODUCT LIFE

11.

TROUBLESHOOTING

12.

CHART OF MEDICAL DEVICE SYMBOLS USED

13.

CHART OF ELECTRICAL SYMBOLS USED

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 2 of 68

1. INTRODUCTION Congratulations on the purchase of your new LLS-050 LED Light Source! This user-friendly LED light source is a high efficiency light source utilizing state-of-theart superior illumination technology. It offers a variety of features such as: •

6500º K daylight brightness for good color definition

•

Quiet operation

•

Long life, 50,000 hrs.

•

Compact and light weight

•

Turret which adapts to various types of light guides

•

Pulse-width Modulation (PWM) Electrical Dimming

In short, you have chosen the best and we would like to make sure you receive the optimal results with your new LED Light Source by using it correctly. This Operator Manual will help you to install the device and optimally integrate it with other components of your system. It will also instruct you how to operate the LED Light Source and how to keep it clean. It will give you maintenance and service guidelines as well as recommendations for best performance results. 1.1 INDICATIONS FOR USE: The LED Light Source is used to illuminate the site of surgery during minimally invasive surgical procedures in arthroscopy (orthopedic surgery), laparoscopy (general and gynecological surgery) and in Endoscopy (general, gastroenterological and ENT surgery) The light is transmitted from the light source through a fiber optic cable and a scope.

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 3 of 68

2. WARNINGS/CAUTIONS Caution practitioner.

Federal law restricts this device to sale by or on the order of a licensed

Caution To prevent fire or electric shock, do not open or expose the LED light source unit to rain or moisture. Refer all servicing to qualified personnel only. Caution Not suitable for use in presence of flammable anesthetic mixture with air or with oxygen or nitrous oxide. Caution To prevent any potential electro-magnetic interference, do not use any kind of cellular phone near the light source. Caution This product should be used only with type BF endoscopic instruments which have been certified according to IEC 60601-1 for medical equipment and IEC 60601-2-18 for endoscopic equipment.

This symbol indicates type BF equipment. Caution User must not alter this device in any fashion. statements of suitability for any purpose.

Doing so voids all warranties and

Caution All devices connecting to the LED Light Source must be classified as medical equipment. Additional information processing equipment connected to the LED Light Source, a Medical System and the operator must determine that all equipment complies with the appropriate end-product standards (such as IEC 60950 or IEC 60065 and the Standard for Medical System, IEC 60601-1-1). Caution Always set the intensity control to the minimum level and insert the fiberoptic cable into the unit before turning on the power. When light is not required at the surgical site, the intensity control should be should be set to the fully dimmed position. If it becomes necessary to remove the fiber optic cable without turning the unit off, turn the intensity control to the fully dimmed position. Caution EQUIPMENT CONNECTION - The fiber optic cable must be a NON-CONDUCTIVE CABLE. It should not have conductive shielding or any other conductive connection between the patient and equipment. Such connection will impair safety of the equipment. It must be rinsed free of soaking/disinfectant solution and dried before plugging into the LED light source receptacle. Ensure the optical surface is clean before engaging into the light source. Caution User is responsible for determining if interruption of light output will create an unacceptable risk. If this determination is made arrangements should be taken to reduce the risk

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 4 of 68

3. SPECIFICATIONS Item

Specification

Light Source type

LED (Light Emitting Diode)

Power

50 Watt

Color temperature

6500º K

Led life

50,000 hours (typical)

Light guide adapter Brightness control

Turret type to fit your choice of four: Storz, ACMI, Wolf, Olympus PWM (Pulse-width Modulation) – 0-100% Dimming

Input voltage

100-240V AC, 50/60 Hz

Rated Power

52 watt

Regulatory Approvals Equipment Class

UL60601-1,CAN/CSA C22.2 No.601.1 (SUP1+AM2), EN 60601-1-2 and CE marked BF-type

Mode of Operation

Continuous operation

Water Resistant

Not Protected Equipment, IPX0

Operating Environment Temperature Relative Humidity Air Pressure

+0° to +40° C (32° to 104° F) 0 to 85%rh, non condensing 700 to 1060 hPa

Storage Environment Temperature Relative Humidity Air Pressure

-20° to +60° C (-4° to 140° F) 30 to 95%rh, non condensing 700 to 1060 hPa

Dimensions

4.65” W x 3.32” H x 7.25” D

Weight

2.5 lbs./1.14 kg

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 5 of 68

4. OPERATING ELEMENTS, SYMBOLS AND FUNCTIONS 4.1 FRONT PANEL

1

2

3

Figure 1. LED Light Source Front Panel

No.

Name

Function

1

Power switch

Turns the light source on and off. Fan will operate

2

Light guide adapter

Turret type to fit your choice of four: Storz, ACMI, Wolf, Olympus

3

Intensity Control

Electronically controls the light output

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 6 of 68

4.2 REAR PANEL

2

3

4

1

Figure 2. LED Light Source Rear Panel No.

Name

Function

1

AC main inlet

Accepts AC Power cord

2

Fuse

2A, 250V (1/4” x 1 ¼”) time delay

3

Grounding Connector

For potential equalization

4

Venting grids

Allows adequate ventilation and cooling of the light source

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 7 of 68

4.3 BOTTOM PANEL Figure 3. LED Light Source Product Label

No.

Name

Function

1

Product Label

Product Label containing: Model Number, Serial Number, Electrical Ratings, Manufacturer Name, Regulatory Marks and FDA “Rx Only” Symbol.

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 8 of 68

5. INSTALLATION 5.1 SETTING UP THE LED LIGHT SOURCE Place the LED light source on a stable surface (cart, counter, stand, etc.). NOTE

Avoid places where the light source may be splashed with liquid. Absolutely DO NOT use in any environment with explosive or flammable gases. DO NOT block the venting grids of the light source or impede exhaust air flow. Users must ensure that ventilation air temperatures are below the maximum rating for the light source and are not influenced by warm exhaust from other sources.

Make sure the power switch is in OFF position. Connect AC power cord to the power inlet located on the rear panel of the light source.

CAUTION

Use only cords provided with the light source. Plug the AC power cord into a wall outlet using the three-prong plug supplied with the unit. To prevent electric shock, connect power cords of peripheral equipment through medical isolation transformers.

CAUTION NOTE

CAUTION

When using medical isolation transformer, be sure to check the transformer power ratings. Make sure that the power cord is connected to the main power with three-prong plug (USA use UL2601-1 rated isolation transformers and/or power strips only). When used in clinical or residential areas near radio or TV units, this equipment may be subjected to radio interference. To avoid adverse electromagnetic effects, DO NOT operate this equipment near RF energy equipment.

5.2 CONNECTING THE FIBER OPTIC CABLE Turn intensity control to the minimum setting. Connect the light cable to the instrument and then plug the light cable endfitting into the port on the front panel.

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 9 of 68

6. OPERATION 6.1 POWERING UP THE LED LIGHT SOURCE To operate the LED light source: Turn on the power switch. The indicator on power switch will light. 6.2 LIGHT BRIGHTNESS DISPLAY AND CONTROL The light brightness adjustment enables the user to obtain a brighter or darker illumination of the object of observation. Adjust the light intensity by turning the intensity control knob.

7. CLEANING NOTE

Always disconnect the power cord before cleaning the system.

The unit can be cleaned with any cleaning agent, which is used for external cleaning of electric equipment, according to instructions given by the manufacturer of the cleaning solution. Do not allow excessive moisture or liquids to come in direct contact with the unit. Do not use cleaning agents that are not permitted for use with plastics, i.e., ammonia, acetone, salty acids (HCl), etc. Do not allow cleaning agents or liquids to enter the control unit outlets or vents at side, back or bottom of the unit.

8. DISINFECTION 8.1 DISINFECTING THE UNIT NOTE

Always disconnect the power cord before cleaning the system.

Use any disinfectant agents which are commonly applied while disinfecting surfaces of electric medical equipment. Such disinfectant agents are usually in the form of sprays or damp cloths. Follow the instructions given by the manufacturer of the disinfectant solution.

9. SERVICING AND REPAIR Defective items of equipment are to be serviced and repaired exclusively by persons authorized by the manufacturer. All repair work shall employ original manufacturer’s parts only. 9.1 FUSE REPLACEMENT Always disconnect power cord and turn main switch off before fuse replacement. CAUTION

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 10 of 68

Turn light source off and unplug power cord. On back of unit remove fuse by turning fuse cover and pulling out fuse. Replace fuse with 2 AMP (1/4” x 1 ¼”) time delay 250V rated fuse. Insert back into fuse housing. Re-connect the power cord and turn the LED light source on according to section 6.1.

9.2 LIMITED WARRANTY Your LED light source carries a 3-years warranty from the date of shipment on workmanship and all defects of material. Should your product prove to have such defects within 3 years of the shipment. ST TECHNOLOGIES will repair or replace the product or component part without charge. Should your LED Light Source product(s) need servicing under this warranty, please contact, ST TECHNOLOGIES return authorization documentation. You should carefully pack unit in a sturdy carton and ship it to the factory. Please include a note describing the defects, your name, telephone number and a return address. Warranty does not cover equipment subject to misuse, accidental damage, normal wear and tear or if transferred to a new owner without authorization from, ST TECHNOLOGIES. This warranty gives you specific legal rights and you may also have other rights that vary from state to state. POST WARRANTY REPAIRS: You may return your product(s) for repair, shipping prepaid to the factory. Your product will be inspected and an estimate of repair charges will be submitted to you for approval. Payment must be received before repairs are completed.

10.

•

In the US:

877-814-2237 (toll free)

•

FAX number:

904 733-4832

•

Customer Service

904-208-2291

END OF PRODUCT LIFE In accordance with the European Waste from Electrical and Electronic Equipment (WEEE) directive, we encourage our customers to recycle this product whenever possible. Disposal of this unit must be performed in accordance with the applicable local environmental regulations. In the US a list of recyclers in your area can be found at: http:/www.eiae.org/. Please contact customer service to issue a return authorization to return product to manufacturer at the end of product life.

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 11 of 68

11.

TROUBLESHOOTING Problem

Solution

The power indicator (refer to 4.1) is not lit.

A. Check that the AC power cord is properly connected. B. Check the unit fuses. If necessary, replace. Turn intensity control knob clockwise to increase light output intensity

The power indicator is lit, but lamp will not ignite.

12.

CHART OF MEDICAL DEVICE SYMBOLS USED Manufacturer Date of manufacture (YYYYMM or YYYY) “Authorized Representative” in the European Community Caution, consult accompanying documents Caution: Federal law restricts this device to sale by or on the order of a licensed healthcare practitioner Consult Instructions for Use CE mark

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 12 of 68

13.

CHART OF ELECTRICAL SYMBOLS USED AC Current Equipotentiality Power on

Power off Type BF

Protective Earth (Ground)

Product labeling Product label containing model number, serial number, electrical ratings, manufacturer name, Regulatory marks, and FDA “Rx Only” symbol.

LIT158 CUDA® SURGICAL (English)

Rev. C Date of Revision:06/11/14 Page 13 of 68

LLS-050 Manuel d’utilisation pour source lumineuse à LED

 ST Technologies 6018 Bowdendale Avenue Jacksonville, FL 32216 Customer Service: 904 208-2291 Toll Free 877 814-2237 EC|REP

LIT158 CUDA® FIBEROPTICS (French)

RMS UK, Ltd. 28 Trinity Road Nailsea, Somerset BS48 4NU United Kingdom TEL: 01275 858891

Rév. C Date de révision:06/11/14 Page 14 de 65

TABLE DES MATIÈRES 1. 2.

INTRODUCTION 1,1 INDICATIONS POUR L'USAGE AVERTISSEMENTS

3.

CARACTÉRISTIQUES TECHNIQUES

4.

ÉLÉMENTS DE FONCTIONNEMENT, SYMBOLES ET FONCTIONS 4.1 PANNEAU AVANT 4.2 PANNEAU ARRIÈRE 4.3 PANNEAU INFÉRIEUR

5.

INSTALLATION 5.1 CONFIGURATION DE LA SOURCE LUMINEUSE 5.2 BRANCHEMENT DU CÂBLE D'ÉCLAIRAGE

6.

FONCTIONNEMENT 6.1 ALIMENTATION DE LA SOURCE LUMINEUSE 6.2 CONTRÔLE DE LA LUMINOSITÉ DE L'ÉCLAIRAGE

7.

NETTOYAGE

8.

DÉSINFECTION 8.1 DÉSINFECTION DE L'UNITÉ

9.

SERVICE ET RÉPARATION 9.2 REMPLACEMENT DU FUSIBLE

10.

FIN DE VIE DU PRODUIT

11.

DÉPANNAGE

12.

TABLEAU DES SYMBOLES DE DISPOSITIFS MEDICAUX UTILISES

13.

SYMBOLES ELECTRIQUES

LIT158 CUDA® FIBEROPTICS (French)

Rév. C Date de révision:06/11/14 Page 15 de 65

LLS-050 LED-Lichtquelle Gebrauchsanleitung

 ST Technologies 6018 Bowdendale Avenue Jacksonville, FL 32216 Customer Service: 904 208-2291 Toll Free 877 814-2237 EC|REP

LIT158 CUDA® SURGICAL (German)

RMS UK, Ltd. 28 Trinity Road Nailsea, Somerset BS48 4NU United Kingdom TEL: 01275 858891

Rev. C Datum Auflage:06/11/14 Seite 27 von 65

LLS-050 Fonte di luce a LED Manuale operatore

 ST Technologies 6018 Bowdendale Avenue Jacksonville, FL 32216 Customer Service: 904 208-2291 Toll Free 877 814-2237 EC|REP

LIT158 CUDA® SURGICAL (Italian)

RMS UK, Ltd. 28 Trinity Road Nailsea, Somerset BS48 4NU United Kingdom TEL: 01275 858891

Rev. C Data di Revisione:06/11/14 Pag. 40 di 65

LLS-050 Manual del Operador Fuente de Luz LED

 ST Technologies 6018 Bowdendale Avenue Jacksonville, FL 32216 Customer Service: 904 208-2291 Toll Free 877 814-2237 EC|REP

LIT158 CUDA® SURGICAL (Spanish)

RMS UK, Ltd. 28 Trinity Road Nailsea, Somerset BS48 4NU United Kingdom TEL: 01275 858891

Rev. C Fecha de revision:06/11/14 Página 53 de 65

ÍNDICE 1. 2.

INTRODUCCIÓN 1.1 INDICACIONES PARA el USO ADVERTENCIAS

3.

ESPECIFICACIONES

4.

ELEMENTOS OPERATIVOS, SÍMBOLOS Y FUNCIONES 4.1 PANEL FRONTAL 4.2 PANEL POSTERIOR 4.3 PANEL INFERIOR

5.

INSTALACIÓN 5.1 CONFIGURACIÓN DE LA FUENTE DE LUZ 5.2 CONEXIÓN DEL CABLE DE LUZ

6.

FUNCIONAMIENTO 6.1 ENCENDIDO DE LA FUENTE DE LUZ 6.2 CONTROL DE CLARIDAD DE LA LUZ

7.

LIMPIEZA

8.

DESINFECCIÓN 8.1 DESINFECCIÓN DE LA UNIDAD

9.

REVISIÓN Y REPARACIÓN 9.6 SUSTITUCIÓN DE FUSIBLES

10.

FIN DE VIDA DEL PRODUCTO

11.

LOCALIZACIÓN Y RESOLUCIÓN DE PROBLEMAS

12.

TABLA DE SÍMBOLOS USADOS EN DISPOSITIVOS MÉDICOS

13.

SÍMBOLOS ELÉCTRICOS

LIT158 CUDA® SURGICAL (Spanish)

Rev. C Fecha de revision:06/11/14 Página 54 de 65