Molift Air 200,350,500 Periodic Inspection Checklist Rev A

Molift Air 200/350/500 / PI15701 Rev A / www.etac.com

Components, Molift Air 500

Trolley Connection point buttons

Hoist Side cover

Lifting belt

4

Updated according to legal req.

2021-03-1

Rev.

Description:

Revised D

Emergency stop / Emergency lowering

Quick release coupling

3

Updated according to legal req.

2021-03-21

Rev.

Description:

Revised Date: Revised By: Released Date: Released By: ECP ID:

ELJ

ELJ

2021-03-21

Quick release pin

Sling bar

Hand control

GS1-128 Size 76,5mm x 25,5mm Silver background

Size 76,5mm x 25,5mm Silver background QR code URL: http://q.etac.com/004w Product label 500

76,5mm

ID label

Air 500

Gross weight 519,4kg / 1145,1lbs SWL 500kg / 1102,3lbs 24V DC, IP24 Duty cycle 10%

25,5mm 25,5mm(01)XXXXXXXXXXXXXX(11)XXXXXX(21)XXXXXX ABCDEFGHIJ

XXXXXX

60601-1

SWL value

YYYY-MM-DD

76,5mm

Serial no.

Serial number

Article no.

Etac A/S Parallelvej 3 DK-8751 Gedved www.etac.com

Production date

Art. number of marked product

2

Molift Air 200/350/500 / PI15701 Rev A / www.etac.com

A copy of this document is available for download at www.etac.com.

The hoist’s software Molift Service tool provides option to enter date of PI and name of inspector along with additional information. Molift recommends adding all observations / remarks concerning the hoist in the Molift Service tool for complete history log of the hoist

Scan QR code on product label for accessing product home page. The user manual can be found in the document section. Article no. (see ID label): ...

Visual examination

Serial no. (see ID label):

Visual examination of load bearing structure to make sure there is no damage, cracks, frays or deformation. All checkpoints must be checked to approve hoist for further use

... Production Year: ... OK

Owner:

Lifting belt

...

Product label

Specify model:

Plastic covers Hand control

Molift Air 200 Molift Air 350 Molift Air 500

Cables Other electronics

Sling shall be inspected separately and is not included in this inspection.

Sling bar Sling bar hooks

Service light indicator

Quick release coupling

Note colour of service light indicator: Status

Not OK

Instruction for use / user manual is present / available

Service light (No light)

Mode Ready for use Perform periodic Yellow inspection Green blink Order service Red Perform service Red (and sound Perform service when activated) immediately

Situation of use Home Hospital Nursing home Other The periodic inspection is to be performed by a person who is suitable and properly qualified and well acquainted with the design, use and care of the hoist 3

Molift Air 200/350/500 / PI15701 Rev A / www.etac.com

Functional examination

OK

Not OK Perform new visual control; Damage and deformations as described above. Any damaged parts must be repaired or replaced and test is repeated once more until the hoist performs correctly

Test FUNCTION and inspect for wear and damage. All checkpoints must be checked to approve hoist for further use OK

Not OK Emergency stop button is fully operational and interrupts power when engaged. Reset switch Check tools for emergency lowering (found behind covers)

Charger is operational Battery. Battery light is green, and service light indicator is OFF Accessories (e.g. scale, propulsion, IRC):

Electrical emergency lowering  and control (buttons, wire H sockets, and battery indicator) Hand control functionality Quick release coupling (swivel joint moves freely when turned 360° and without noise) Quick release pin Connection point buttons Angle sensor. Pull lifting belt sideways in all four directions Checked that the hoist functions correctly and runs without load all the way up and down without abnormal noise End stops If all points so far are “OK”, hoist shall be tested with SWL. NOTE!: Ensure SWL for the complete hoist system exceeds or equals hoist SWL before any load testing. Perform one lifting cycle with weight equal to SWL with min. range of 500 mm in the top of lifting range. Brake must not slip when loaded. Movement must be smooth and even, and without unusual noise Move hoist loaded with SWL through entire rail system. Check deflection and suspension is acceptable

... ...

Performed by Full name: ... Date/Place: ... Signature: ... Approved without faults Next inspection (YYYY / MM): .../... Perform “Reset of hoist” Hoist is marked with “Out of order” and sent for repair Hoist is not eligible for repair and taken out of service If periodic inspection reveals any defect, wear or other damage that jeopardises the safety of the patient the hoist may not be used until the deficiency has been eliminated. The owner is notified

4

Molift Air 200/350/500 / PI15701 Rev A / www.etac.com

Due to legal requirements this document or a copy must be filed with the owner’s service log book If approved without faults, apply inspection label on cover inside and mark with month and year for next inspection. When ordering label, use item no. 1100306 Mark label with month and year for next inspection

Reset of hoist

1 Ensure hoist is ON and emergency stop is deactivated.

2

2

3

3

Press and hold both buttons for approx. 4 sec.: First beep when start pressing. Second beep - stop pressing. 2 sec. pause

Pause for approx. 2 sec.

4

2

Press and hold both buttons for approx. 4 sec.: First beep(s) -  stop pressing. Inspection indicatorlight is OFF - reset complete.

5