User Manual
164 Pages
Preview
Page 1
Molift Smart 150 EN - User manual
BM09201 Rev. H 2021-06-08
Molift Smart 150 / www.etac.com
English manual Important This user manual contains important safety instructions and information regarding the use of the lifter and accessories. In this manual the user is the person being lifted. The assistant is the person operating the lifter. Warning! This symbol indicates important information related to safety. Follow these instructions carefully. Read User Manual before use! It is important to fully understand the content of the user manual before attempting to use the equipment. Visit www.etac.com for download of documentation to ensure you have the latest version.
4
Molift Smart 150 / www.etac.com
EN
Molift Smart 150
DE
Lifter components:
Lifting arm
Push/pull handles
Suspension
Battery
Manual emergency lowering
Lifting column
SV
NO
Hand control
Electric emergency lowering Emergency stop
Battery indicator Locking handle Chassis
Legs
Pedals for leg adjustment
ES
FR
Wheel / castor (rear with brake)
IT
Service indicator
FI
Motor / actuator
It is ideal for hospitals and institutional care settings, and can also be used in privates homes. The lifter should only be used for transfers across short distances, such as between a chair and a bed or into bathroom / rest room. The lifter is not intended to transport the user over longer distances. 5
DA
Molift Smart 150 is a foldable mobile lifter intended for lifting and transferring a person from/ to bed, floor, chair, wheelchair or toilet with a sling. The lifter is made of light-weight materials, has castors and electric actuator and is powered by a battery. It has manual adjustable legs and a lifting capacity of 150 kg ( 330 lbs).
NL
About Molift Smart 150
Molift Smart 150 / www.etac.com
General CE declaration The product, and its related accessories, described in this instruction for use (IFU), is in compliance with the regulation (EU) 2017/745 of 5. April 2017 – as a medical device, risk class I. The product has been tested and approved by a third party according to standards IEC 60601-1, IEC 60601-1-2 and EN/ISO 10535:2006. Any serious incident that occurs in relation to the device should be reported to the manufacturer and the competent authority of the Member State in which the user and/or patient is established.
Conditions for use Lift and transfer of a person will always pose a certain risk, and only trained personnel are allowed to use the equipment and accessories covered by this user manual.
Modifications and use of components made by other manufacturers. We recommend only using Molift components and spare parts. Declaration of conformity is not valid and Etac is not responsible for warranty if any modifications are made to the product. Etac shall not be liable for faults or accidents that can occur when using components made by other manufacturers. Only certified personnel are allowed to open lifter or accessories to perform service or repair. Risk of injury from rotating parts and electric shock. The lifter is not intended to be operated by the person being lifted. Warranty notice Two-year warranty against defects in workmanship and materials of our products. One-year warranty for batteries. Please refer to www.etac.com for terms and conditions.
Product identification Product label
Warning labels and symbols
The Product labels barcode contain article number, serial number and production date.
Symbols used on the product, explained in more detail: Type BF applied part
Battery light
Smart 150
Gross weight 176kg / 388lbs SWL 150kg / 330lbs 14.4V DC, IP24 Duty cycle 10%
CE marked
Certification body mark 60601-1
Refer to user manual
60601-1
Manufacturer
Indoor use only
Date of manufacture YYYY-MM-DD
6
Do not dispose in general waste
Catalogue number
Emergency lowering
Serial number
Service light
Medical Device
Molift Smart 150 / www.etac.com
Safe Working Load (SWL)
EN
Technical data Operating forces button
150 kg (330 lbs)
Buttons on handset: 3.4 N
Material:
Ex. battery: 25 kg / incl. battery: 25,8 kg
Battery:
Art: 0541000 14.4 V NiMH 2.6 Ah
Motor
Aluminum, plastic, steel
DE
Weight of unit
Lifting motor/actuator: 12 V DC
Turning diameter:
Battery charger:
Number of lifts with fully charged battery:
100-240 V AC, 50-60 Hz 0,9 A output
40 lifts ( 75 kg / 165 lbs, 50 cm / 20 inches)
Lifting speed
Expected Lifetime:
50,7 mm/second (1.99 inches/second) with 75kg (165 lbs) load
The lifter has an expected lifetime of 30 000 cycles or 10 years.
Protection class
Measurements folded (LxWxH):
Hand control IP24 Lift motor IP24
SV
1160 x 475 x 355mm (45.66 x 18.7 x 14”)
Maximum A-weighted sound power level
FI
LWA = 49,4 dB
CSP
1180 mm (4629/64in)
215 mm (815/32in)
1 2 3 A B
Highest position 1860mm Maximum reach position 1260mm Lowest position Maximum reach 7 at 600 mm Maximum reach from base
NL
1 Highest position: 1860 mm (7315/64in) 2 Max reach: 1260 mm (4939/64in) 3 Lowest position: 400 mm (153/4in)
1200 mm (471/4in)
545 mm
110mm (421/64in)
410 mm (169/64in)
610 mm 630 mm (241/64in) (2451/64in)
820 mm (329/32in)
ES
885 mm (3427/32in)
IT
FR
h=600 530 mm (2055/64in)
1030 mm (4035/64in)
240 mm (929/64in)
400mm 610mm 630 mm
DA
1315 mm (5149/64in)
1880 mm (741/64in)
1065 mm (4159/64in)
925 mm (3627/64in)
2
w=700
660 mm (2563/64)
200 mm (77/8in)
860 mm (3355/64in)
545mm (2129/64in)
1450 mm (573/32in)
1665 mm (6535/64in)
1905 mm (75in)
455 mm (1729/32in)
475 mm (1845/64)
1
3
NO
1300 mm (51,2 inches)
Molift Smart 150 / www.etac.com
Assembly Battery and Hand control
Charge the battery. The battery must not be in the battery holder on the lifting column during assembly or folding.
Assembly
Remove the transport elastic band.
1. Connect hand control to bottom of battery holder. 2. Insert battery with terminals facing down. 3. Pull out elastic band and guide hand control through. Pull some of the cable through so the hand control does not fall to the floor when dropped.
Engange the break on the rear castors by stepping on the left pedal set. Open the legs.
Folding (Transport mode) Run the lifting arm all the way down, and remove battery. Fold the lifter in reverse order of assembly. Fix the suspension back into the hook. It is possible to split the lifter into two separate parts by lifting the column from the chassis completely.
Lift up the lifting column and slide it down into the bracket on the chassis. Make sure it is placed completely in the bottom of chassis.
Checklist after assembly Do not use the product until you have checked all points in the checklist below
The column must be fixed with the locking handle on the back of the chassis. Pull the suspension out of the transport hook
Use this checklist to verify that the lifter is properly installed and can operate correctly and safely before use. Ensure that the lifting arm, lifting column and suspension are properly fixed and that there are no loose parts on the lifter. Make sure battery is charged (no lights on the battery indicator). Check that the lifter has no apparent damage or other faults. Perform a lift with load (approximately 50 kg)
Be careful not to get legs/arms/hands caught between the parts when raising/folding down the lifting column.
8
Safe working load (SWL)
Use only accessories and slings that are adjusted to fit the user, type of disability, size, weight and type of transfer.
The lifter is marked with Safe Working Load (SWL) The lowest SWL shall always be used if safe working load (SWL) differs between lifter, suspension and body support unit
Working pause ratio/Duty Cycle. Molift Smart 150 should not be run constantly for more than 2 minutes (with maximum load), and rest for minimum 18 minutes. Duty cycle 10% intermittence.
Molift lifters shall only be used to lift persons. Never use the lifter to lift or move objects of any kind.
DE
General safety precautions
NO
How to use Molift Smart 150
EN
Molift Smart 150 / www.etac.com
Make sure lifter has no visible damage, defects or deformations Make sure battery indicator is not illuminated and service indicator is green Make sure wheels are rolling freely and lifter is easy to manouvre
Inspection to be performed monthly: Test all the lifters functions and make sure lifter does not make any abnormal sounds Test emergency stop button and emergency lowering If there are any faults or defects, the lift needs to be taken out of operation and marked ”out of order”
Leg spread mechanism is mechanical, and operated by two pedals. One pedal for legs inwards and one pedal for legs outwards. Step on selected pedal to open or close legs.
FR
The hand control has 2 buttons, one for lifting and another for lowering of lifting arm. The hand control has an indicator that will illuminate when battery level is low and the battery requires charging.
IT
Hand control
FI
Inspection to be performed daily or before use:
SV
Before use / Daily check / Monthly
Hand Control 2 buttons Art. no. 0440002
NL
NB! Open legs provides increased stability and better access to chair or toilet.
ES
Legs - In / Out
9
DA
Lifting Arm - Up / Down
Molift Smart 150 / www.etac.com
Safety devices
Emergency Stop / Emergency lowering
Molift Smart 150 is equipped with several safety devices, which are intended to prevent damage to personnel and equipment in the case of incorrect use.
Manual Emergency lowering
The lifter has an overload sensor preventing the lifter to be operated if the load exceeds SWL.
Electrical Emergency lowering
The lifting arm is hinged to prevent the arm and suspension from squeezing the user. The actuator will not produce any force when moving downwards.
Emergency stop
The legs are folded together during transport to make the lifter as small as possible. When assembling the lifter, the legs must be opened to working position. The lifting column will not fix into the bracket if the legs are not adjusted beyond transport position - a safety feature ensures this.
Emergency stop
The electronics are disabled if overheated. Wait until the lifter has cooled down before using it again.
Electrical emergency lowering
The emergency stop shuts off the power when pushed in. Turn clockwise to reset (OK to operate when the green ring is visible). Push and hold button for electrical emergency lowering to lower lifting arm. The electrical emergency lowering function does not work when the emergency stop is activated.
Push / Pull handles Use the pull handles to move the lifter.
Manual emergency lowering
Do not push or pull the user, lifting arm or actuator. This may cause instability and lifter may tip over. The lifter shall only be used for movement over short distances. It is not a replacement for wheelchair or similar.
Brakes Pull handle on the actuator upwards to start emergency lowering, and the lifting arm moves downwards when loaded. The lowering will increase in speed the higher the handle is pulled. Release the handle gently. Releasing the handle too quickly may cause person injury or damage to the lifter. The manual emergency lowering function on the actuator should only be used when the electrical emergency lowering does not work.
Rear castors are equipped with brakes. Step on pedal to lock brakes. Flip up to unlock.
10
Molift Smart 150 / www.etac.com
Transport and operating conditions
Battery and service indicator (LED)
Transport and storage
The lifter has two indicator lights on battery holder.
For long time storage it is recommended that the emergency stop button is activated (pushed in). The lifter can be stored and transported under temperatures between -25 - 70 °C.
Service indicator
Recharge battery upon receipt, and then every six months, to avoid battery failure. Used batteries must be disposed of as special waste according to local rules and regulations. Do not dispose in general waste Batteries must be fully charged and drained completely a couple of times before it achieves full capacity. Also follow this procedure if the lifter has not been in use for a long period (4 weeks or more)
Number of lifts performed is calculated and recorded by the lifters electronics. After a certain period of operation a signal is given to indicate that service is required. Mode Service indicator No light Power saving (Stand by) Green Ready for use Yellow Order service Red Perform service Red + sound Perform service immediately
SV
FI
IT
Service indicator
FR
Molift Smart 150 is equipped with a 14.4 V 2.6Ah NiMH battery. The battery has a life expectancy of approx. 500 charging cycles.
The battery indicator (LED) will illuminate and make a sound when battery level is low and the lifter requires charging. When this occurs the lifter will have sufficient power available for one full lifting cycle with max load. When battery is critically low it is only possible to lower the lifting arm.
Service scope Service involves replacing the lifting motor and inspection/replacement of worn parts. This must be carried out by authorized personnel.
ES
Battery
Battery indicator (LED)
Service is needed when the service light is red (calculated 10.000 lifts in SWL.)
NL
Medical electrical equipment requires special precautions regarding electromagnetic compatibility (EMC). Portable or mobile radio communication equipment may affect the medical electrical equipment, and should be kept minimum 25 cm (10 inches) from the lifters electronics.
The electrical system has a power save function which will turn off the electrical system after ten minutes without activity. All lights will turn off. The system is activated when pushing one of the operating buttons
11
DA
The lifter is designed for use at standard room temperatures (+5 to +40°C). Air pressure: 70 - 106 kPa Relative humidity: 15 - 93 % Following storage or transport at other temperatures leave the lifter in a room with a suitable temperature until it reaches a safe operating temperature.
NO
Battery indicator
Operating
x2
DE
EN
Electronics
Molift Smart 150 / www.etac.com
Charging Battery indicator (LED)
Battery charger
Mains cable (disconnecting device)
Battery charger The battery charger can be used as a tabletop charger or mounted to a vertical wall surface close to a power outlet, minimum 120 cm above the floor. The charger has to be used outside the patient environment. The Charger must be placed or installed in a way that makes it easy to disconnect mains cable plug. Take care not to damage the cable. The charger can be connected to the power outlet at all times. Battery charger 12-24V Art. no. 1340100 PowerPac 14,4 V NiMH Art. no. 0541000
Charger indicator Description of battery indicator (LED): LED Mode Yellow Ready for use, no battery connected Yellow blinking Initialization Red Fast Charge Green/Yellow Top-off charge Green Trickle charge Red/Green Error
12
Transfer
Molift Smart 150 has a 4-point suspension for different types of transfers; sitting, recumbent or ambulating.
SV
Read user manual for the sling prior to use.
Do not to use damaged or badly worn slings.
Slings made by other manufacturers We recommend only using Molift slings. Etac shall not be liable for faults or accidents that can occur when using slings made by other manufacturers.
Lifting and lowering
1. Check that the sling is correctly fitted around the user and that the strap loops are correctly fitted to the suspension hooks. 2. Stretch the sling straps without lifting the user. Ensure that all four loops of the sling are securely fastened to avoid the user slipping or falling. 3. Lift user, and perform transfer.
The 4-point suspension must always be positioned across the user, to prevent the user from unintentionally sliding out of the sling. 13
DA
NL
ES
FR
When moving the user, stand to the side of the person you are lifting. Make sure that arms and legs do not obstruct the seat, bed, etc. Keep eye contact with the user to help them feel safe.
FI
It is important that the sling has been tested with the individual user and for the intended lifting situation.
The suspensions hook design prevents sling to be inadvertently detached when mounted correct.
IT
Using slings
NO
DE
Plan the lifting operation in advance to ensure that it is as safe and smooth as possible. Remember to work ergonomically. Assess the risks and take notes. The assistant is responsible for the safety of the user.
EN
Molift Smart 150 / www.etac.com
Molift Smart 150 / www.etac.com
Transfer
Lowering into sitting
Try to position the user as low as possible (preferably resting the feet on the chassis) when transferring the lifter with a suspended user. In this way the centre of gravity will be low and reduce the risk of instability.
When transferring the user into sitting, the following techniques can be used when lowering the user as far back into the seat as possible: A P osition the user with the help of the push handle B P ush gently on the user’s knees C T ilt the seat backwards
Never lift the user higher than necessary to carry out a lift. Remember that wheels on a mobile lift must NOT be locked.
User must be facing lifter when lifting or lowering from or into a chair.
Never leave a user unattended in a lifting situation. Be careful during movement, the suspended user may swing during turns, stops and starts. Be careful when manoeuvring close to furniture to prevent the suspended user from colliding with these objects. The lifter shall not be used to lift or move users on sloping surfaces Avoid deep pile carpets, high thresholds, uneven surfaces or other obstacles that may block the castors. The lifter may become unstable if forced over such obstacles increasing the risk of tipping over.
14
Accessories
EN
Molift Smart 150 / www.etac.com
Recommended optional equipment and accessories for Molift Smart 150.
DE
Slings
NO
Etac supplies a wide selection of slings for different types of transfers. The Molift RgoSling sling series is developed to be combined with a 4-point suspension but the sling also works with a 2-point suspension. See the combination list in the slings user manual for the correct sling and suspension combination. The Molift RgoSling sling series is available in sizes XXS – XXL, in polyester and polyester mesh.
FI
SV
Rgosling Mediumback Padded (XS-XXL) Rgosling Highback Padded (XS-XXL) Rgosling Mediumback Net (XXS-XXL) Rgosling Highback Net (XXS-XXL) Rgosling Toilet Lowback (XXS-XXL) Rgosling Toilet Highback (XXS-XXL) Rgosling Ampu Mediumback (XXS-XXL) Rgosling Ampu Highback (XXS-XXL) Rgosling Ambulating Vest Rgosling Comfort Highback (S-L)
Accessories:
IT
Rgosling Extension Loops Art. no.: 1721600 Rgosling Ambulating Vest Groin strap (XXS-XL)
FR
Transport/Storage Travel Suitcase for Molift Smart 150 Art. no. 0990200
ES
This hard shell suitcase provides additional protection when transporting by air. It is TSA approved for air travel and ideal for the client with an active life.
The soft shell travel bag has extra large transport wheels. It protects the lift, and enables easy transporting.
15
DA
NL
Travel Bag for Molift Smart 150 Art. no. 3049175
Molift Smart 150 / www.etac.com
Maintenance Cleaning and disinfection
Reconditioning
Clean on a regular basis. Clean surfaces with a damp cloth using an appropriate pH-neutral detergent. Do not use solvents or strong liquids, this may damage surfaces on the lifter. For disinfection when needed; use isopropyl alcohol. Avoid abrasive cleaning products. Remove hair and pile from the castors and verify that the castors rotates freely. Clean contact and hand control with isopropyl alcohol to remove grease and dirt. Check emergency stop and emergency lowering after cleaning. The lift should not be exposed to running water.
Follow cleaning and assembly procedure, complete periodic inspection and use checklist after assembly to recondition the lifter.
Recycling Refer to “Recycling instructions” for how to properly dispose of product. This can be found on www.etac.com.
Spare parts A list of spare parts is available on request.
Make sure not to damage or remove labels when cleaning.
Periodic inspection Periodic inspection scope Periodic inspection is a visual examination (particularly of the lifter’s load bearing structure and lifting mechanism with attachments, brakes, controls, safety devices and person-support devices) according to Periodic inspection report for Molift Smart 150. This can be found on www.etac.com. If there is any problems with the lifter that could jeopardize someones safety, the lifter shall immediately be taken out of service and marked “out of order”. Do not use the lifter untill it is repaired.
If the inspection reveals defects and damages, the owner shall be notified. When periodic inspection is completed the inspector shall mark the lifter with a sticker on the control label showing the date when periodic inspection is performed and a label (with 6-digit ID from Etac or distributor) showing who has performed the periodic control. The control label can be found on the right side of the battery holder, and this will then indicate the date when next Inspection is due.
Mark label with month and year of inspection
Periodic inspection shall be performed annually or more frequently if required by local requirements. The inspection must be performed by service personnel authorized by Etac. Contact Etac at [email protected] for training and authorization or recommendation of an approved service partner. When performing a periodic inspection, the inspector shall fill out the inspection report for Molift Smart 150. The reports should be retained by the person(s) responsible for servicing the lifter.
16
The lifting legs move uncontrolled.
NL
The lifter does not respond to hand control action Emergency stop button is activated. / The lifting arm does not move. Turn button clockwise to reset emergency stop. Battery is empty. Change or charge battery. The lifters electronics is overheated. Wait for it to cool down. The lifter is overloaded. Make sure the load does not exceed SWL. Hand control is not plugged in properly. Plug in Hand control properly. Hand control, plug or cord can be broken an should be replaced. Defective control electronics. Contact local representative for service. Battery does not charge Faulty battery. Check indicators on charger when charging. Try another battery. Faulty battery charger. Check indicators on charger when charging. See chapter “Charging”. Try another charger.
17
DA
The lifting arm moves uncontrolled.
DE
The castors move unevenly because of pile and dust. Clean the castors. Remove hair and dirt. Short circuit between hand control and lifter. Clean hand control plug surfaced with alcohol to remove grease. Defective hand control. Replace hand control. The control electronics has failed. Contact local representative for service. The leg opening mechanism has failed. The product is unsafe to operate . Contact local representative for service
NO
The lifter moves unevenly on a plane surface
SV
The lifting column is not correctly positioned in the chassis. Assemble column and chassis, and lock column by the locking handle on the chassis.
FI
The lifting column is wobbly
IT
Possible cause / action
FR
Symptom
ES
Troubleshooting
EN
Molift Smart 150 / www.etac.com
Molift Smart 150 NO - Brukermanual
BM09203 Rev. I 2021-06-08
Molift Smart 150 NL - Handleiding
BM09209 Rev. H 2021-06-08