GE Healthcare

eBike PC Firmware Version 1.8 Operators Manual

Operators Manual

138 Pages

File Type: PDF

File Size: 5.18 MB

File Name: GE Healthcare - eBike PC Firmware Version 1.8 Operators Manual.pdf

Preview

Page 1

eBike PC

2018112-027 - D

eBike with Control Terminal PC Firmware Version 1.8

Operator’s Manual 2018112-027 ENG

Revision D

NOTE: The information in this manual only applies to the eBike with control terminal PC, firmware version 1.8. It does not apply to earlier firmware versions. Due to continuing product innovation, specifications in this manual are subject to change without notice.

CardioSmart, CardioSoft, CardioSys, CASE, and MAC are trademarks owned by GE Medical Systems Information Technologies, a General Electric Company going to market as GE Healthcare. All other marks are owned by their respective owners. © 2003, 2008. General Electric Company. All rights reserved.

eBike with Control Terminal PC

2018112-027 Revision D 2008-02

Contents

1 Intended Use, Safety Information

2 Setup and Mains Connection

3 Preparation

4 Running an Exercise Test

5 Taking the Blood Pressure

6 Configuration

7 Error Messages

8 Cleaning, Maintenance, Disposal

9 Technical Specifications

10 Order Information

11 Appendix

Revision History This manual is subject to the change order service of GE Medical Systems Information Technologies. The revision code, a letter that follows the document part number, changes with every update of the manual. P/N / Revision

Date

Comment

2018112-001 Revision B

2003-12

Initial Release, ECO 075 558

2018112-001 Revision C

2004-04

ECO 076 092

2018112-001 Revision D

2004-07

ECO 077 414

2018112-001 Revision E

2005-07

ECO 080 463

2018112-027 Revision A

2005-10

MR 55686

2018112-027 Revision B

2006-11

ECO 085 811

2018112-027 Revision C

2007-08

ECO 087 883 Revised pages: 7, 32, 33, 36

2018112-027 Revision D

2008-02

eBike with Control Terminal PC

V1.7JV1.8

General Information

y The safety information given in this manual is

y The product eBike with Control Terminal PC bears

classified as follows:

the CE marking CE-0123 (notified body TÜV Süd Product Service GmbH, Ridlerstr. 65, 80339 München, Germany) indicating its compliance with the provisions of the Council Directive 93/42/EEC

Danger indicates an imminent hazard. If not avoided, the hazard will result in death or serious injury.

about medical devices and fulfills the essential

Warning

requirements of Annex I of this directive. It is an

indicates a hazard. If not avoided, the hazard can

MDD class IIa product. y The device fulfills the requirements of standard EN

result in death or serious injury.

60601-1 "Medical Electrical Equipment, Part 1: General Requirements for Safety" as well as the

Caution

interference protection requirements of standard EN

indicates a potential hazard. If not avoided, this

60601-1-2 "Electromagnetic Compatibility – Medical

hazard may result in minor personal injury or

Electrical Devices".

product/property damage.

y The device is in radio-interference protection class B in accordance with CISPR11/EN 55011. y The CE marking covers only the accessories listed in the "Order Information" chapter.

y To ensure patient safety and interference-free operation and to guarantee the specified measuring accuracy, we recommend only original equipment

y This manual is an integral part of the equipment. It

accessories as available through GE Medical Systems

should be available to the equipment operator at all

distribution. The user is responsible if accessories

times. Close observance of the information given in

from other manufacturers are used.

the manual is a prerequisite for proper equipment

y GE Medical Systems Information Technologies is

performance and correct operation and ensures

responsible for the effects on safety, reliability, and

patient and operator safety. Please note that

performance of the device, only if

information pertinent to several chapters is given

– assembly operations, extensions, readjustments,

only once. Therefore, carefully read the manual

modifications, or repairs are carried out by GE

once in its entirety.

Medical Systems Information Technologies or by

y If unauthorized personnel opens the control terminal, damaging the calibration sticker, any warranty claim

persons authorized by GE Medical Systems Information Technologies, – the device is used in accordance with the

shall become void. y This manual reflects the equipment specifications and

instructions given in this manual.

applicable safety standards valid at the time of printing. All rights are reserved for devices, circuits, techniques, software programs, and names appearing in this manual. y On request GE Medical Systems Information Technologies will provide a detailed Service Manual.

eBike with Control Terminal PC

2018112-027 Revision D

General Information

Manufacturer: ergoline GmbH Lindenstraße 5 D-72475 Bitz, Germany Tel. +49 7431 9894-0 Fax +49 7431 9894-127 Distributor: GE Medical Systems Information Technologies, Inc. 8200 West Tower Avenue Milwaukee, WI 53223 USA Tel. +1.414.355.5000 888.558.5120 (USA only) Fax +1.414.355.3790

The country of manufacture appears on the device label.

2018112-027 Revision D

eBike with Control Terminal PC

Intended Use, Safety Information

1 7

Intended Use, Safety Information

1.1 Intended Use

NIBP

The eBike with control terminal PC is a computer-

eBike

controlled, medical-grade bicycle ergometer. At pedal

speeds between 30 and 130 RPM and loads between 20

3 8 4

and 999 W, the ergometer operates independent of the pedal speed. Figure 9-1 shows the speed-independent range.

10 11 12

this manual for exercise tests as well as for rehabilitation of cardiac and cardiovascular patients. If the ergometer is used for other purposes, the manufacturer cannot be held liable for personal injuries or property damage resulting

from unintended use of the equipment.

Two eBike models are available: eBike basic and eBike comfort. What differentiates the eBike comfort from the

NIBP

The ergometer is only intended to be used as instructed in

eBike basic is the manual height adjustment for the

eBike

handlebar and the electric height adjustment for the

saddle. The patient may remain seated on the saddle

3 4

while it is raised or lowered.

The eBike with control terminal PC can be used both as a stand-alone device and in conjunction with GE Medical

Systems Information Technologies electrocardiographs

(See “Connection to Electrocardiographs” ). When used

in conjunction with an electrocardiograph, the electrocardiograph will control the bicycle ergometer. Furthermore, the electrocardiograph starts the

sphygmomanometer (option) integrated in the ergometer. Additional blood pressure measurements can be initiated Figure 1-1 Controls and indicators eBike basic (top), eBike comfort (bottom) 1 Control terminal

manually.

Connection for blood pressure cuff, type B applied part ( )

measuring values.

Adjusts angle of handlebar

Blood pressure cuff

Adjusts height of handlebar (eBike comfort only)

Castors

The parts of the equipment described in this

Speed readout for patient

manual, including all accessories, that come in

Adjusts height of saddle (eBike basic only)

contact with the patient during the intended use,

Indicates saddle height (eBike comfort only)

fulfill the biocompatibility requirements of the

Power switch

applicable standards if used as intended. If you

Connection panel

have questions in this matter, please contact GE

Leg levellers to ensure ergometer stability

Medical Systems Information Technologies or its

The display on the control terminal indicates the current

The connected electrocardiograph provides a full documentation of the test. Biocompatibility

Sales Representatives.

eBike with Control Terminal PC

2018112-027 Revision D

Intended Use, Safety Information

1.2 Equipment Symbols With this button on the control terminal, you can either bring up the main menu or go back one menu level. NIBP

With this button on the control terminal, a blood pressure measurement can be initiated before or during the exercise test. The same button can be used to stop a blood pressure measurement. Symbol at the blood pressure cuff connector: type B applied part. Caution, consult accompanying documents. Caution, consult accompanying documents. Type B applied part. This symbol indicates that the waste of electrical and electronic equipment must not be disposed as unsorted municipal waste and must be collected separately. Consult operating instructions. This symbol indicates that the device was tested and certified according the Russian safety standards specified by GOST. Catalog number. Serial number. CE Mark per the Medical Device Directive 93/42/EEC. Manufacturer’s identification

Date of manufacture. The number found under this symbol is the date of manufacture in the YYYYMM format.

2018112-027 Revision D

eBike with Control Terminal PC

Intended Use, Safety Information

1.3 Safety Information Warning

Danger Explosion Hazard - The device is not designed for use in areas where an

Equipment Failure - – Cellular telephones must not be used in the

explosion hazard may occur. An explosion hazard

immediate vicinity, because they may interfere

may result from the use of flammable anesthetics,

with the proper functioning of the ergometer.

skin cleansing agents and disinfectants.

Electromagnetic interference most probably exists when the watt reading changes frequently even though the speed is above 30 RPM.

Warning Patient Hazard, Equipment Damage -

Shock Hazard -

– Protect the eBike from direct sunlight.

– When the ergometer is connected to other

Otherwise equipment components may reach

equipment or if a medical system is created, it

inadmissibly high temperatures. The eBike is a

must be ensured that the added leakage currents

medical device and must NEVER be used

do not present a hazard. If you have questions

outdoors. Furthermore, the device has no

about this issue, please contact your GE

additional protection against ingress of

Medical Systems Information Technologies

humidity. Humidity that has entered the device

dealer or GE Medical Systems Information

may cause equipment failure and can increase

Technologies Service.

the risk of electric shock.

– For use, the ergometer may only be connected to

Also, do not operate the eBike in the vicinity of

electric installations that fulfill the local

power installations, because they may impair

requirements.

equipment functions.

Patient Hazard -

Risk to Persons -

The German Medical Device Operator Ordinance

Before using the ergometer, the operator must

(MPBetreibV, § 5) demands that users

ascertain that it is in correct working order and operating condition. In particular, the cables and connectors must be checked for signs of damage. Damaged parts must be replaced immediately, before use.

ergometer – must be familiar with the routines for the handling and assembly of the ergometer – must be familiar with and observe the safety

Equipment Failure - – The special shielded cables supplied by GE Medical Systems Information Technologies must be used to connect the device to other pieces of equipment.

– must have been trained in the use of the

rules and regulations for the operation of this type of equipment – must be informed about any other pertinent rules and regulations (e.g. safety instructions) – must be informed about the potential hazards arising from the use of this type of equipment.

eBike with Control Terminal PC

2018112-027 Revision D

Intended Use, Safety Information

Special NIBP Safety Instructions Note

Warning

– The blood pressure module and the approved

Patient Hazard - – Do not use a cuff to take blood pressure

accessories are defibrillation-proof and can

measurements on patients suffering from sickle

remain attached to the patient during

cell anemia or where skin lesions are likely to

defibrillation.

occur.

– If the cuff pressure exceeds the maximum value

– The cuff may cause hematomas in patients with

of 300 mmHg during inflation, the inflation

severe blood coagulation disease. In these

procedure will be aborted and the cuff will

instances, the user must make a decision for or

deflate. As a redundant safety precaution, the

against automatic blood pressure

cuff is immediately deflated when the cuff pressure exceeds 320 mmHg.

measurements.

You can check the proper functioning of this safety precaution by abruptly bending your arm while the cuff is being inflated, causing a brief overpressure in the cuff. The cuff must

Caution

immediately deflate.

Compromised Measuring Accuracy - – Arrhythmias occurring frequently during a

– Measurements that do not yield a valid

measurement may compromise the accuracy of

measurement will not be repeated during the

the measuring values. In certain cases, a valid

exercise test.

measurement will not be possible.

– If the inflation phase takes longer than 40

– Electromagnetic fields may also impair the measuring accuracy.

seconds or if an adequate pressure does not build up in the cuff within a reasonable period of time, the measurement will be aborted and the cuff will deflate. – If a valid measurement cannot be completed within 120 seconds, the measurement will be aborted and the cuff will deflate. – If the cuff pressure remains constant for some time, the measurement will also be aborted and the cuff will deflate.

Applicable laws, regulations and directives – 93/42/EEC (Medical Device Directive of the EU) – 89/336/EEC (Electromagnetic Compatibility Directive of the EU) – EN 1060-1 Non-invasive sphygmomanometers, Part 1: General requirements – EN 1060-3 Non-invasive sphygmomanometers, Part 3: Supplementary requirements for electromechanical blood pressure measuring systems

2018112-027 Revision D

eBike with Control Terminal PC

Setup and Mains Connection

Set up the ergometer where you intend to use it and adjust the two leg levellers 12 for ergometer stability (Figure 11). Protect the ergometer and, in particular, the saddle cover from direct sunlight.

Mounting the Handlebar

a b

y Remove the two screws a from the clamping plate (Figure 2-1). y Holding the clamping plate, turn the clamping lever b counterclockwise until it can be removed. y Take off the clamping plate. y Insert the handlebar (pointing down) and secure it with the clamping plate (Figure 2-2).

Figure 2-1 Removing the clamping plate a Fastening screws b

Clamping lever

y Introduce the two screws a and lightly screw them in. y Insert the clamping lever, turning it clockwise, and tighten lightly.

Note The handlebar should point downward until the control terminal has been installed. Then bring the handlebar to its final position and secure by tightening the clamping lever and the screws. Having tightened the clamping lever, you can bring it to a suitable position by taking it off and reinserting it as desired. Furthermore, the eBike comfort allows you to adjust the height of the handlebar (clamping lever 5, Figure 1-1). Figure 2-2 Mounting the handlebar

eBike with Control Terminal PC

2018112-027 Revision D

Setup and Mains Connection

Installing the Control Terminal y Plug connector A to socket a on the control terminal. Align the notch on connector A with the corresponding groove in socket a.

b B

C A

y Secure the connection by turning the coupling ring at connector A clockwise. y Connect the blue pressure tubing B to the length of tubing b at the control terminal. Be sure to slip the length of tubing entirely over the nozzle. (The black tube C is irrelevant.) y Position the control terminal on the steering column and screw tight with the two screws. Note

Figure 2-3 Installing the control terminal

The control terminal can be installed with the display facing the patient or the operator (Figure 24). Install the control terminal with the display toward the operator and the speed indication toward the patient (see section 4.1 Speed Readout for the Patient).

Figure 2-4 Installing the control terminal

2018112-027 Revision D

eBike with Control Terminal PC

Setup and Mains Connection

Mains Connection y Stand in front of the ergometer and grasp both handles

Caution

of the handlebar.

Equipment Damage - Before connecting the

y Tip the ergometer forward all the way and carefully

ergometer to the power line, make sure that the voltage rating of your local power line matches the

lay it on its handlebar.

value indicated on the device nameplate. The

Now you can access the connector panel on the underside

nameplate is located on the back of the ergometer,

of the ergometer.

at the bottom.

y Connect the power cord to socket a (Figure 2-5). y Secure the connector with the supplied lock a. y Install the strain relief as shown in Figure 2-5. Please note that different strain reliefs are supplied for various cable sizes.

Connection to Electrocardiographs The software supports communication with the following a

electrocardiographs: electrocardiographs (digital control):

electrocardiograph

connection cable

connector on eBike

CardioSys

22336203

port 1, f

CardioSoft

22336203

port 1, f

CASE

22336203

port 1, f

CASE 8000

22336203

port 1, f

MicroLab

22336203

port 1, f

CardioSmart ST*) 22338002

port 3, b

MAC 1200 ST

port 3, b

f d

b 4

4 3

PORT 3

1 7

PORT 2

2 3 6

ANALOG

*) eBike with integrated BP module only d

f PORT 1

SERVICE

Figure 2-5 Connector panel a Power input, instrument fuses b

Digital interface RS232

Analog I/O

For Service

Digital interface RS232

Digital interface RS232 (for Service only)

22338002

electrocardiographs (analog control): electrocardiograph

connection cable

connector on eBike

MAC 5000 ST

2008110-001 2008114-001

ANALOG, c port 3, b

Upon delivery, the eBike is configured for communication with digitally controlled electrocardiographs. For use with electrocardiographs with an analog control system (MAC 5000 ST), the following settings are required (see section 6 "Configuration"): – at Default Mode: PC Mode – at EKG Type: Analog / Digital y Install a strain relief to secure the cable connection.

eBike with Control Terminal PC

2018112-027 Revision D

Setup and Mains Connection

Connecting the Blood Pressure Cuff y Connect the microphone to a (Figure 2-6). y Connect the cuff tubing to the connection sleeve b. It must properly lock into place. To disconnect the tubing, push the knurled sleeve backward. When the blood pressure is taken during exercise tests,

NIBP

care must be taken to prevent motion artifacts. For this reason the Velcro tape (Figure 2-7) supplied with the equipment must be used to secure the cuff tubing to the eBike

handlebar: y Open the large Velcro tape and wrap it around the

handlebar as shown in Figure 2-8. y Use the small Velcro tape to secure the cuff tubing.

Take care not to squeeze the cuff tubing.

Figure 2-6 Blood pressure cuff connections a Microphone jack

Transport

y Disconnect all connected cables.

Socket for cuff tubing

y Stand in front of the ergometer and grasp both handles of the handlebar. y Tip the ergometer forward until it rests only on the castors. y Wait until you have achieved an equilibrium before moving the ergometer. y When you have reached the new location, lower the ergometer very carefully. Otherwise, severe damage may occur. Caution Equipment Damage - Avoid strong vibrations of the ergometer during transport. Figure 2-7 Velcro tape securing the cuff tubing

Figure 2-8 Securing the cuff tubing to the handlebar

2018112-027 Revision D

eBike with Control Terminal PC

Preparation

3.1 Turning the Device On and Testing Its Performance y Push the power switch (10, Figure 1-1) to turn on the

eBike

ergometer (green indicator lights up). y Make sure that the patient does not pedal at the time the ergometer is switched on and during the selftest.

Selftest running

Note When operating the ergometer in conjunction with

Figure 3-1 Initial screen during selftest

the MAC 5000 ST, turn the devices on and off in the following order: ON: MAC 5000 ST first, eBike second OFF: eBike first, MAC 5000 ST second.

PC Mode Ergometry Manual Settings

The ergometer runs an automatic selftest (Figure 3-1). Then the main menu appears (Figure 3-2). When the main menu appears, the ergometer is ready for operation.

Select

Note The device may be configured to default to one of

Figure 3-2 Main menu

the operating modes. In this case you will see the initial screen of the selected operating mode instead of the main menu. You can display the main menu with the

button (see section 6

"Configuration"). a

NIBP

eBike

If an error code (e.g. E:01) appears after the

selftest, please refer to chapter 7 for

troubleshooting information. It is important to switch on the eBike before applying the blood pressure cuff to the patient. In addition to the three softkeys c (Figure 3-3) the control

Figure 3-3 Control terminal buttons a Starts and stops a blood pressure measurement b Brings up the main menu or returns to the previous menu level c, d, e Softkeys activating the function described above

terminal also accommodates buttons With button

NIBP

a and

a blood pressure measurement can be

initiated before or during the exercise test. The same button can be used to stop a blood pressure measurement. With the

button, you can either bring up the main

menu or go back one menu level.

eBike with Control Terminal PC

2018112-027 Revision D

Preparation

The functions of the three softkeys change with the displayed menu. The function keys can be used to activate the function displayed above. In the main menu, PC-Betrieb Ergometrie Manuell Einstellungen

for example, the left and right softkeys are used to move the bar cursor up and down, while the softkey in the middle is used to Select an option.

Auswahl

PC Mode:

The ergometer will be controlled from the electrocardiograph (see section 4.2).

Ergometry:

stored test protocols (see section 4.3). Manual:

Figure 3-4 Main menu

The ergometer will be controlled by the

The ergometer will be controlled manually (see section 4.4).

Settings: Einstellungen S Betrieb P tCa- nBdeat r d ieb P Ero gg o rmaemt rmi e K M oa nn turealsl t L E ai ns st ät en ldl e u rnugnegn Sprache

Ergometer configuration (see section 6).

3.2 Changing the Language Upon delivery of the ergometer, the screen texts are displayed in German. Follow these steps to change the

Auswahl

language: y Press button

b (Figure 3-3) to display the main

menu (Figure 3-4). y Using buttons d and e, position the bar cursor on Einstellungen and press button c to confirm the

Figure 3-5 Settings menu

selection. The settings menu appears (Figure 3-5). y Using the cursor keys d and e, position the bar cursor

Sprache

on Sprache and press button c to confirm the

Deutsch English Français Español Italiano

selection. The language menu appears (Figure 3-6).

Auswahl

y Using the cursor keys d and e, position the bar cursor on your language and press button c to confirm the selection.

Figure 3-6 Language menu

2018112-027 Revision D

eBike with Control Terminal PC

Preparation

3.3 Preparing the Patient Adjusting Saddle and Handlebar On the eBike basic, the saddle height is adjusted manually (clamping lever 7, Figure 3-7), on the eBike comfort, electrically. NIBP

Adjust the saddle height as shown in Figure 3-7: There

eBike

7 3

should be a 10° angle between the axis formed by the

approx. 10˚

upper body and the thigh when the pedal is in its lower position.

Display 8 indicates the saddle height as a numeric value

(eBike comfort only). Set the handlebar to a position where it is comfortable for the patient to reach sitting upright. To do so, open clamping lever 3. On the eBike comfort, you can also adjust the height Figure 3-7 Adjusting saddle height and handlebar 3 Adjusts angle of handlebar 5 Adjusts height of handlebar (eBike comfort only) 7 Adjusts height of saddle (eBike basic only) 8 Indicates saddle height (eBike comfort only)

of the handlebar (clamping lever 5). Note – Adust the height of the handlebar. Tighten the clamping lever securely. Do not overtighten.

– Lubricate the threading of the clamping lever once every 3 months, using a suitable grease

Watt

min

such as OKS 470.

/min Adjusting the saddle height of the eBike comfort

/ mmHg

/min Saddle

y Ask the patient to sit on the saddle. y In the main menu, select the desired mode of operation, e.g. PC Mode (Figure 3-8). y Adjust the saddle height with the right and left

Figure 3-8 PC Mode menu a Blood pressure readings (systolic, diastolic) or cuff pressure during measurement b Current load c Duration of exercise test (in "Manual" and "Ergometry" modes only) d Pulse rate (configurable) e Speed (revolutions/minute) f Saddle up g Saddle down

softkeys f, g. Note The patient may remain seated on the saddle while the height is being adjusted. In PC Mode, the saddle height adjustment buttons appear automatically when the electrocardiograph start signal is detected.

eBike with Control Terminal PC

2018112-027 Revision D

Preparation

Applying the Blood Pressure Cuff Note Observe the following order when applying the blood pressure cuff: 14 cm

2017911-010 1,3 m 2017911-011 2,0 m -33 cm 23

1. Switch on the eBike and wait for the main menu to appear.

LATEX

2. Apply the blood pressure cuff. Caution Erroneous Measurements - Figure 3-9 Correct cuff size

– Select a cuff size suitable for the circumference of the patient’s arm. The maximum permitted circumference is indicated on each cuff. When

closing the Velcro fastener, ensure that the index line at the metal clasp (a, Figure 3-10) is within the INDEX range (b) identified by the

2017911-010 1,3 m 2017911-011 2,0 m -33 cm 23 14 cm

INDEX

2017911-010 1,3 m 2017911-011 2,0 m -33 cm 23

LATEX LATEX

arrow and not outside. – Apply the cuff directly on the skin. Rolled up sleeves must not impede blood circulation in the upper arm. Use only the cuffs listed in chapter 10.

Figure 3-10 Wrong cuff size

– Loose cuffs will cause erroneous measurements; overtight cuffs may constrict blood vessels or cause skin lesions or hematomas. y Ensure that the microphone is correctly positioned in the red cuff pocket: the metal side must face the artery. y Apply the deflated cuff on the patient’s arm. Take care that – the bottom end of the cuff does not reach the bend of the elbow – the microphone (identified by the red tab and white arrow) is exactly above the brachial artery (Figure 3-12). To ensure accurate blood pressure measurements during an exercise test, the microphone (red tab) must be in the correct position.

Figure 3-11 Applying the cuff

– the tab is placed below the metal clasp as shown in Figure 3-11.

2018112-027 Revision D

eBike with Control Terminal PC

Preparation

y Tighten the cuff and close the Velcro fastener. Ensure that the cuff does not slip down or impede circulation of the blood. y Check that the cuff tubing does not knock against any objects during the patient’s exercise test (Figure 313). y Instruct your patient to avoid excessive contractions of the muscles in their upper arm during a blood pressure measurement and to put their hands flat on the handlebar without grasping it. For additional important information on blood pressure measurements, please refer to chapter 5.

Warning Figure 3-12 Microphone (identified by red tab) over brachial artery

Patient Hazard - If, by mistake, excessive pressure builds up in the cuff, either remove the cuff immediately from the patient’s arm or disconnect the cuff tubing at the control terminal. The same applies when the cuff does not deflate correctly.

Figure 3-13 Cuff tubing

eBike with Control Terminal PC

2018112-027 Revision D

Running an Exercise Test

4.1 Speed Readout for Patient There are three LEDs on the speed display that tell the

patient whether they are pedaling too fast, too slow or at

the correct speed. The limit values can be configured (see section 6 "Configuration").

Figure 4-1 Speed readout for patient a illuminates when the speed is low b illuminates when the speed is correct c illuminates when the speed is high

4.2 PC Mode Selecting and Starting the Operating Mode In PC mode, the connected electrocardiograph will control the ergometer. All you can do is initiate a blood pressure measurement with

PC Mode Ergometry Manual Settings

NIBP

y Using the right or left softkey, position the bar cursor on PC Mode, then press the softkey in the middle to Select the option. The initial menu will appear (Figure 4-3).

Select

Note

Figure 4-2 Main menu

The device may be configured to default to one of the operating modes. In this case you will see the

initial screen of the selected operating mode instead of the main menu. You can display the main menu

Watt

min

/min

with the

button (see section 6

"Configuration"). Now the ergometer waits for the start signal from the electrocardiograph.

/ mmHg

/min

y When you have finished preparing the patient, initiate the exercise test on the electrocardiograph.

Saddle

y The ergometer will emit three beeps and the speed display will blink three times to indicate the

Figure 4-3 PC mode initial menu a Blood pressure readings (systolic, diastolic) or cuff pressure during measurement b Current load c Duration of exercise test (in "Manual" and "Ergometry" modes only) d Pulse rate (configurable) e Speed (revolutions/minute) f Saddle up g Saddle down

2018112-027 Revision D

beginning of the test. Now the patient should start pedaling.

eBike with Control Terminal PC

Previous Page Next Page