GE Healthcare
Responder AED Rev C Operators Manual
Operators Manual
52 Pages
Preview
Page 1
Operator’s Manual
2022105-201rC
REVISION HISTORY Part number 2022105-201 Rev A 2022105-201 Rev B 2022105-201 Rev C
Date October 2006 December 2006 July 2007
Comment Initial Release AHA Guidelines added Revised for misc. minor updates, new symbols and EMC table added
TABLE OF CONTENTS SECTION 1: INTRODUCTION ... 3 OVERVIEW... 3 INDICATIONS FOR USE/INTENDED USE... 3 AED DESCRIPTION... 3 SAFETY TERMS AND DEFINITIONS... 4 SAFETY TERMS AND CONDITIONS... 4 SAFETY ALERT DESCRIPTIONS ... 4 SYMBOL DESCRIPTIONS... 6 SAFETY AND PERFORMANCE STANDARDS... 8 OPERATOR TRAINING REQUIREMENTS ... 9
SECTION 2: GETTING STARTED... 11 OVERVIEW... 11 UNPACKING AND INSPECTING... 11 ENVIRONMENTAL OPERATING AND STANDBY CONDITIONS ... 11 AED PARTS... 12 INTELLISENSE® BATTERY ... 13 PADS ... 15 AED INDICATORS ... 16 SETTING THE AED INTERNAL CLOCK ... 18 VOICE PROMPTS AND TEXT DISPLAY... 19
SECTION 3: PERFORMING A RESCUE ... 23 OVERVIEW... 23 HOW TO PERFORM A RESCUE... 23 WARNINGS ... 25 AFTER A RESCUE ATTEMPT... 26
i
SECTION 4: DATA MANAGEMENT ... 27 OVERVIEW...27 RECORDING THE RESCUE DATA ...27 REVIEWING THE RESCUE DATA ...27 RESCUELINK OVERVIEW ...28 RESCUELINK INSTALLATION INSTRUCTIONS ...29 MULTIPLE RESCUE FUNCTIONALITY ...29
SECTION 5: MAINTENANCE & TROUBLESHOOTING ... 31 OVERVIEW...31 SELF-TESTS ...31 INDICATOR TROUBLESHOOTING TABLE ...32 SCHEDULED MAINTENANCE ...32 AUTHORIZED REPAIR SERVICE ...34 FREQUENTLY ASKED QUESTIONS ...35
SECTION 6: TECHNICAL DATA... 37 OVERVIEW...37 PARAMETERS ...37 RHYTHMX® AED ECG ANALYSIS ALGORHITHM ...40 STAR BIPHASIC WAVEFORM ...42 STAR BIPHASIC ENERGY PROTOCOLS FOR RESPONDER AED ...42 ELECTROMAGNETIC COMPATIBILITY REQUIREMENTS ...44
SECTION 7: ACCESSORIES ... 49 OVERVIEW...49 RESPONDER AEDs ...49 AED ACCESSORIES ...50
SECTION 8: CONTACT INFORMATION / CUSTOMER SERVICE ... 51
ii
Section 1: Introduction
SECTION 1: INTRODUCTION OVERVIEW Become familiar with the controls and how to use the AED properly before operating the product. TOPIC
PAGE #
INDICATIONS FOR USE / INTENDED USE
3
AED DESCRIPTION
3
SAFETY TERMS AND DEFINITIONS
5
SAFETY TERMS AND CONDITIONS
5
SAFETY ALERT DESCRIPTIONS
5
SYMBOL DESCRIPTIONS
6
SAFETY AND PERFORMANCE STANDARDS
8
OPERATOR TRAINING REQUIREMENTS
9
INDICATIONS FOR USE/INTENDED USE The AED with STAR Biphasic Waveform is intended to be used by personnel who have been trained in its operation. The operator should be qualified by training in basic life support, CPR/AED or other physician-authorized emergency medical response. The device is indicated for emergency treatment of victims exhibiting symptoms of sudden cardiac arrest that are unresponsive and not breathing. If the victim is breathing post-resuscitation, the AED should be left attached to allow for acquisition and detection of the ECG rhythm. If a shockable ventricular tachyarrhythmia recurs, the device will charge automatically and advise the operator to deliver therapy.
WARNING: When the patient is a child or infant under 8 years of age or weighs less than 55 lbs (25kg), the AED should be used with the Model 9730 Pediatric Attenuated Defibrillation Electrode Pads. Therapy should not be delayed to determine the patient’s exact age or weight.
AED DESCRIPTION The AED is a self-testing, battery-operated automated external defibrillator (AED). After applying the AED pads to the patient’s chest, the AED automatically analyzes the patient’s electrocardiogram (ECG) and advises the operator to push the button and deliver a shock if needed. The AED uses one button and guides the operator through the rescue using a combination of voice prompts, audible alerts, and visible indicators.
2022105-201 Rev C
Copyright © 2007 General Electric Company
Page 3 of 51
SAFETY TERMS AND DEFINITIONS BEFORE OPERATING THE RESPONDER AED Become familiar with the various safety alerts in this section. Safety alerts identify potential hazards using symbols and words to explain what could potentially harm you, the patient, or the Responder AED.
SAFETY TERMS AND CONDITIONS The triangle attention symbol shown below, left, identifies the potential hazard categories. The definition of each category is as follows: DANGER: This alert identifies hazards that will cause serious personal injury or death. WARNING: This alert identifies hazards that may cause serious personal injury or death. CAUTION: This alert identifies hazards that may cause minor personal injury, product damage, or property damage.
SAFETY ALERT DESCRIPTIONS The following is a list of Responder AED safety alerts that appear in this section and throughout this manual. You must read, understand, and heed these safety alerts before attempting to operate the AED. DANGER: Fire and Explosion Hazard Do not use the AED in the presence of flammable gases (including concentrated oxygen) to avoid possible explosion or fire hazard. WARNING: Shock Hazard Defibrillation shock current flowing through unwanted pathways is potentially a serious electrical shock hazard. To avoid this hazard during defibrillation abide by all of the following: • Do not touch the patient, unless performance of CPR is indicated • Do not touch metal objects in contact with the patient • Keep defibrillation pads clear of other pads or metal parts in contact with patient • Disconnect all non-defibrillator proof equipment from the patient before defibrillation WARNING: Shock and Possible Equipment Damage Disconnect all non-defibrillator proof equipment from the patient before defibrillation to prevent electrical shock and potential damage to the equipment. WARNING: Electric Shock and Fire Hazard Do not connect any telephones or unauthorized connectors to the socket on this equipment. WARNING: Battery is Not Rechargeable Do not attempt to recharge the battery. Any attempt to recharge the battery may result in an explosion or fire hazard. WARNING: Shock Hazard Do not disassemble the AED! Failure to observe this warning can result in personal injury or death. Refer maintenance issues to authorized service personnel. CAUTION: Temperature/Humidity/Pressure Extremes Exposing the AED to extreme environmental conditions outside of its operating parameters may compromise the ability of the AED to function properly. The RescueReady® daily self-test verifies the impact of extreme environmental conditions on the AED by checking temperature, humidity and pressure; if the daily self-test determines environmental conditions outside of the AEDs operating parameters for 5 consecutive days, a "SERVICE REQUIRED" alert will be issued to prompt the user to move the AED to environmental conditions within the acceptable operating parameters at once. See Section 6 – Technical Data, Parameters, Operation and Standby Conditions. Page 4 of 51
Copyright © 2007, General Electric Company
2022105-201 Rev C
Section 1: Introduction CAUTION: Lithium Sulfur Dioxide Battery Pressurized contents: Never recharge, short circuit, puncture, deform, or expose to temperatures above 65°C (149°F). Remove the battery when discharged. CAUTION: Battery Disposal Recycle or dispose of the lithium battery in accordance with all federal, state and local laws. To avoid fire and explosion hazard, do not burn or incinerate the battery. CAUTION: Use only GE Approved Equipment Using batteries, pads, cables, or optional equipment other than those approved by GE may cause the AED to function improperly during a rescue. CAUTION: Possible Improper AED Performance Using pads that are damaged or expired may result in improper AED performance. CAUTION: Serial Communication Cable The AED will not function during a rescue when the serial communication cable is connected to its serial port. When the serial communication cable is connected to the AED during a rescue, the prompt “Remove Cable to Continue Rescue” will be heard until you remove the serial communication cable. CAUTION: Possible Radio Frequency (RF) Susceptibility RF susceptibility from cellular phones, CB radios and FM 2-way radio may cause incorrect rhythm recognition and subsequent shock advisory. When attempting a rescue using the AED, do not operate wireless radiotelephones within 1 meter of the AED – turn power OFF to the radiotelephone and other like equipment near the incident. CAUTION: Possible Interference with Implanted Pacemaker Therapy should not be delayed for patients with implanted pacemakers and a defibrillation attempt should be made if the patient is unconscious and not breathing. The AED has pacemaker detection and rejection, however, with 1 some pacemakers the AED may not advise a defibrillation shock. Placing Pads: • Do not place the pads directly over an implanted device. • Place the pad at least one inch from any implanted device. CAUTION: Moving the Patient During a Rescue During a rescue attempt, excessive jostling or moving of the patient may cause AEDs to improperly analyze the patient’s cardiac rhythm. Stop all motion or vibration before attempting a rescue. CAUTION: Serial Communication Cable The serial communication cable is only for use with the AED; it is not to be used with a telephone. CAUTION: Systems Statement Equipment connected to the analog and digital interfaces must be certified to the respective IEC Standards (i.e. IEC 60950-1 for data processing equipment and IEC 60601-1 for medical equipment). Furthermore, all configurations shall comply with the system standard IEC 60601-1-1. Anybody who connects additional equipment to the signal input part or signal output part configures a medical system, and is therefore, responsible that the system complies with the requirements of the system standard IEC 60601-1-1. CAUTION: Case Cleaning Solutions When disinfecting the case, use a non-oxidizing disinfectant, such as ammonium salts or a glutaraldehyde based cleaning solution, to avoid damage to the metal connectors. CAUTION: The AED is programmed with software that has been tested to work with versions of ServiceLink and RescueLink that are included with the AED. When older versions of ServiceLink and RescueLink are used to communicate with this AED, there may be features described in this manual that are not available to be used. Also, when communicating with an older AED with the version of ServiceLink and RescueLink included with this new AED there may be features described in this manual that cannot be edited. The software in most cases will give an error message when incompatibilities occur.
1
Cummins, R., ed., Advanced Cardiac Life Support; AHA (1994): Ch. 4.
2022105-201 Rev C
Copyright © 2007 General Electric Company
Page 5 of 51
SYMBOL DESCRIPTIONS The following symbols may appear in this manual, on the AED, or on its optional components. Some of the symbols represent standards and compliances associated with the AED and its use. Dangerous Voltage: The defibrillator output has high voltage and can present a shock hazard. Please read and understand all safety alerts in this manual before attempting to operate the AED. Attention!: Identifies important information in this manual, on the AED, or on its component parts regarding the safe and proper use of the AED. Defibrillator Proof Type BF Equipment: The AED, when connected to the patient’s chest by the pads, can withstand the effects of an externally applied defibrillation shock. CE Mark: This equipment conforms to essential requirements of the Medical Device Directive 93/42/EEC.
IP24
The AED is protected against the effects of splashing water in accordance with IEC 60529. Classified by ETL Semko with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, CAN/CSA C22.2 No.601.1-M90, EN60601-1 and EN60601-2-4. Conforms to UL Standard UL60601-1. Certified to CAN/CSA Standard C22.2 No. 601.1-M90. International symbol for ON. Open the lid to turn on the AED.
Open the lid to turn ON the AED.
0%
100%
Indicates the AED battery status. The illuminated areas indicate the remaining battery capacity. Check pads. The pads are missing, not connected or have compromised functionality.
Indicates AED requires maintenance by authorized service personnel. When the SHOCK indicator is lit, push this button to deliver a defibrillation shock. When the CONTINUE indicator is lit, push this button to clear the internal memory to allow storage of new rescue data in the AED. (Only for models not equipped with Multiple Rescue software) A red indicator with a BLACK X means the Responder AED requires operator attention or maintenance, and is not RescueReady. This symbol will be referred to as RED in the remainder of this manual. A green indicator without a BLACK X means the Responder AED is RescueReady. This symbol will be referred to as GREEN in the remainder of this manual. Use pads by this date; install battery by this date. Expiration Date. Replace by this date. Page 6 of 51
Copyright © 2007, General Electric Company
2022105-201 Rev C
Section 1: Introduction
Date of manufacture.
Date of factory recertification (R) Latex Free. Disposable. Single patient use only. Tear here to open. Do not recharge battery. Position of pads on the chest of patient.
Dispose of properly in accordance with all state, province, and country regulations. Do not incinerate or expose to open flame. Explosion Hazard: Do not use in the presence of a flammable gas, including Concentrated oxygen. Upper and lower temperature limits. Device Model Number Serial Number Lot Number
Rev
Revision Lithium Sulfur Dioxide Serial Communication Port Additional information is provided in the AED Operator’s Manual. Points to important information regarding the use of the AED. Lift Here
Symbol for the marking of electrical and electronic equipment that must be recycled.
2022105-201 Rev C
Copyright © 2007 General Electric Company
Page 7 of 51
Manufacturer Authorized European Representative Fragile; handle with care
Keep away from rain. (Keep dry)
This way up Stacking limit by number General symbol for recovery/recyclable Humidity Limitations Atmospheric Pressure Limitations In November 2005, the American Heart Association (AHA) and European Resuscitation Council (ERC) released new guidelines for CPR and defibrillation. This symbol indicates that the AED contains the new AHA/ERC guidelines for CPR and defibrillation.
SAFETY AND PERFORMANCE STANDARDS AED MODELS 2019198 The AED has been designed and manufactured to conform to the highest standards of safety and performance including electromagnetic compatibility (EMC). The Responder AED Model 2019198 and pads conform to the applicable requirements of the following: CE CE Marked by BSI 0086 per the Medical Device Directive 93/42/EEC of European Union ETL Classified by ETL Semko with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, CAN/CSA C22.2 No.601.1-M90, EN60601-1 and EN606012-4. Conforms to UL Standard UL60601-1. Certified to CAN/CSA Standard C22.2 No. 601.1-M90. Electrical, Construction, Safety and Performance IEC 60601-1 (1998), Amendments 1 (1991) & 2 (1995) IEC 60601-2-4 (2002) IEC 60601-1-4 (2000) ANSI/AAMI DF-39 (1993) Electromagnetic Compatibility (EMC) IEC 60601-1-2 (2001) IEC 60601-2-4 Section 36 ANSI/AAMI DF-39(1993) Section 3.3.21 Page 8 of 51
Copyright © 2007, General Electric Company
2022105-201 Rev C
Section 1: Introduction
OPERATOR TRAINING REQUIREMENTS Persons authorized to operate the AED must have all of the following minimum training.
• • • •
Defibrillation training and other training as required by state, province, or country regulations. Training on operation and use of the AED. Additional training as required by the physician or Medical Director. A thorough understanding of the procedures in this manual.
Note: Keep valid certificates of training and certification as required by state, province, or country regulations.
Persons authorized to operate AEDs must have training in accordance to state, province or country regulations.
2022105-201 Rev C
Copyright © 2007 General Electric Company
Page 9 of 51
THIS PAGE INTENTIONALLY LEFT BLANK FOR YOUR NOTES:
Page 10 of 51
Copyright © 2007, General Electric Company
2022105-201 Rev C
Section 2: Getting Started
SECTION 2: GETTING STARTED OVERVIEW This section presents information on unpacking and setting up the AED TOPIC
PAGE #
UNPACKING AND INSPECTING ENVIRONMENTAL OPERATING AND STANDBY CONDITIONS AED PARTS
11
12
INTELLISENSE® BATTERY
13
PADS
15
11
AED INDICATORS
16
SETTING THE AED INTERNAL CLOCK
18
VOICE PROMPTS AND TEXT DISPLAY
19
UNPACKING AND INSPECTING Every attempt is made to ensure your order is accurate and complete. However, to be sure that your order is correct, verify the contents of the box against your packing slip.
ENVIRONMENTAL OPERATING AND STANDBY CONDITIONS See Section 6 – Technical Data, Parameters, Environmental Operation and Standby Conditions. CAUTION: Temperature/Humidity/Pressure Extremes Exposing the AED to extreme environmental conditions outside of its operating parameters may compromise the ability of the AED to function properly. The RescueReady® daily self test verifies the impact of extreme environmental conditions on the AED by checking temperature, humidity and pressure; if the daily self test determines environmental conditions outside of the AED’s operating parameters for 5 consecutive days, a "SERVICE REQUIRED" alert will be issued to prompt the user to move the AED to environmental conditions within the acceptable operating parameters at once. See Section 6 – Technical Data, Parameters, Operation and Standby Conditions.
2022105-201 Rev C
Copyright © 2007 General Electric Company
Page 11 of 51
AED PARTS The following drawings show the AED parts and their locations. Battery Compartment
RescueReady Status Indicator Lid
Latch (Push in to open)
Pad Expiration Window
Serial Communication Port (Behind rubber data access cover) Pad Holders
Diagnostic Panel
Speaker
Pad Connector
Text Display SHOCK/CONTINUE Button
THE AED HAS THREE MODES: Operating Mode: Defined as having the battery installed and the lid open. This is the mode the AED would be in during an actual rescue situation. Standby Mode: When the battery is installed, but the lid is closed. In this mode the AED is not being used in a rescue. The device will conduct its routine self-tests to ensure proper operation. Storage Mode: When the battery is removed, such as during shipping or transport. With the battery removed, the AED is unable to perform self-tests or rescues.
Page 12 of 51
Copyright © 2007, General Electric Company
2022105-201 Rev C
Section 2: Getting Started
INTELLISENSE® BATTERY
INSTALLATION • • • •
Insert battery as shown. Push firmly to snap into place. Open the lid for 5 seconds. The Status Indicator turns GREEN
ABOUT THE INTELLISENSE® BATTERY • • • • • • •
When the last battery indicator (LED) is red, the battery is low. Replace the battery right away. A new battery typically takes 10 seconds to charge the AED to maximum energy. AED batteries will provide up to 290 shocks Output voltage: 12VDC (max) Batteries are non-rechargeable Lithium contents: 9.2g (max) Check local regulations for disposal information
MODEL
TYPICAL SHOCKS
2019437(9142) Lithium
2022105-201 Rev C
Up to 290
Copyright © 2007 General Electric Company
Page 13 of 51
BATTERY SHELF LIFE The Responder AED batteries have a shelf life of five years. Shelf life is defined as the length of time a battery can be stored, prior to installation into AED, without degrading its performance. Note: Storing the battery outside its specific range (0-50°C)(30-122°F) will decrease battery life.
BATTERY INSTALLATION 1. With the label on the battery facing the AED battery compartment, insert the battery as shown in the drawing.
2. Push the latched end of the battery firmly into the AED, as shown in the drawing, until the battery snaps into place. The exposed side of the battery should be flush with the outside of the AED case.
3. Open the lid for 5 seconds to initiate self-test. If the battery is installed properly, the STATUS INDICATOR will turn GREEN. Close the lid.
WARNING: Battery is Not Rechargeable Do not attempt to recharge the battery. Any attempt to recharge the battery may result in an explosion or fire hazard. CAUTION: Lithium Sulfur Dioxide Battery Pressurized contents: Never recharge, short circuit, puncture, deform, or expose to temperatures above 65°C (149°F). Remove the battery when discharged. CAUTION: Battery Disposal Recycle or dispose of the lithium battery in accordance with all federal, state and local laws. To avoid fire and explosion hazard, do not burn or incinerate the battery. CAUTION: Use only General Electric Approved Equipment Using batteries, pads, cables, or optional equipment other than those approved by General Electric may cause the Responder AED to function improperly during a rescue. CAUTION: Possible Improper AED Performance Using pads that are damaged or expired may result in improper AED performance
Page 14 of 51
Copyright © 2007, General Electric Company
2022105-201 Rev C
Section 2: Getting Started
PADS The defibrillation pads come in a ready-to-use, sealed package containing one pair of self-adhesive pads with an attached cable and connector. The pads are disposable and should be discarded after each rescue. The pads have a limited shelf life and shall not be used beyond the expiration date. Keep a fresh, unopened pair of pads plugged into the AED at all times. Refer to the pads package label for operation temperatures. On the Responder AED, an audible and visual alert will indicate after the self-test if the pads are missing, unplugged or damaged. CAUTION: Possible Improper AED Performance Using pads that are damaged or expired may result in improper AED performance.
PAD INSTALLATION 1.
Open the lid of the AED.
2.
Place the pads package into the lid so that the expiration label is visible through the clear window on the lid. The expiration date of the pads will then be readable without opening the lid of the AED.
3.
Match the color of the connectors (red to red), then plug the pad connector into the AED case as shown in the drawing.
4.
Tuck the excess cable length in the bottom holder as shown in the drawing. With the pad package completely secured to the AED lid, close the lid.
5.
Make sure the expiration date is visible through the clear window of the lid. Make sure that the STATUS INDICATOR is GREEN.
CAUTION: Use only Approved Equipment Using batteries, pads, cables, or optional equipment other than those approved by General Electric may cause the AED to function improperly during a rescue. CAUTION: Possible Improper AED Performance Using pads that are damaged or expired may result in improper AED performance.
DIRECTIONS FOR USE: 1.
Do NOT open until ready to use, short term use only.
2.
Ensure the skin site is clean and dry.
3.
Separate one pad from liner.
4.
Place one pad on skin in either position.
5.
Peel and place remaining pad.
2022105-201 Rev C
Copyright © 2007 General Electric Company
Page 15 of 51
AED INDICATORS The following indicators are located on the AED.
RESCUEREADY® STATUS INDICATOR The STATUS INDICATOR is located on the Responder AED handle. When this indicator is GREEN, the device is RescueReady. This means the Responder AED self-tests have verified the following: • • •
Battery has an adequate charge. Pads are properly connected to the Responder AED and in working order. Integrity of the internal circuitry is good.
When the STATUS INDICATOR is RED, maintenance is required.
Note: When Status Indicator is RED or Service Indicator is illuminated, device cannot be used to perform a rescue.
AUDIBLE MAINTENANCE INDICATOR When the daily, weekly or monthly self-test determines service is required, an audible beep is sounded every 30 seconds until the lid is opened or the battery power is depleted. Opening and closing the lid may deactivate the beep. If the error is not corrected by the next automatic self-test, the beep will be reactivated.
DIAGNOSTIC PANEL A B C D
Page 16 of 51
SMARTGAUGE BATTERY Indicator PADS Indicator SERVICE Indicator SHOCK/CONTINUE Button
Copyright © 2007, General Electric Company
2022105-201 Rev C
Section 2: Getting Started
SMARTGAUGE™ BATTERY STATUS INDICATOR
0%
The SmartGauge Battery Status Indicator has five (5) LEDs, four (4) green and one (1) red. The right four green LEDs display the remaining capacity of the battery much like a fuel gauge. With use, the green LEDs gradually go out, from right to left, as battery capacity decreases. When the green LEDs go out and the red LED lights up, replace the battery.
100%
Note: When the red LED initially lights up – upon lid opening or at any time during a rescue – a “Battery Low” prompt will be issued at once. However, the AED is capable of delivering at least 9 more defibrillation shocks after the first “Battery Low” prompt is issued. When the AED battery cannot deliver any more shocks, the AED display will show "BATTERY LOW", the STATUS INDICATOR will be RED and the device will "beep" every 30 seconds.. To continue the rescue, leave the lid open, remove the battery, and replace with a fresh battery. If battery replacement takes longer than 60 seconds, the first rescue will be terminated and a second rescue will begin upon opening the lid.
PADS INDICATOR The PADS LED lights up when the pads are: •
Not properly connected to the AED
•
Not within operational specifications (cold, dried, damaged).
•
Disconnected from the patient during a rescue.
SERVICE INDICATOR The SERVICE LED lights up when the AED requires maintenance that can only be performed by qualified service personnel. Note: When Status Indicator is RED or Service Indicator is illuminated, device cannot be used to perform a rescue.
SHOCK/CONTINUE BUTTON •
2022105-201 Rev C
The AED has one button called the SHOCK/CONTINUE button. This button is located on the diagnostic panel.
Copyright © 2007 General Electric Company
Page 17 of 51
SHOCK INDICATOR The word SHOCK and the shock button indicator LED will illuminate red when the AED is ready to deliver a defibrillation shock to the patient.
CONTINUE INDICATOR The word CONTINUE will illuminate yellow and the continue button indicator LED will illuminate red when the previous rescue data has not been cleared from the internal memory. Note: Only for models not equipped with Multiple Rescue software
TEXT DISPLAY The text display has 2 lines of text. The text display provides the operator with information regarding system initialization, text prompts and data during a rescue, and diagnostics. System initialization occurs when the lid is first opened. The text display shows the operator the identifiers for the internal code, voice prompts and text prompts versions. The text display also shows the current date and time. During a rescue, the text display shows the number of shocks delivered and the elapsed time from the beginning of the rescue (when the lid was first opened). During CPR, a countdown timer will be displayed. The text version of the voice prompts will also be displayed. Note: There is a 3 second delay between the time the AED lid is opened and the start of the rescue. This 3 second delay is not included in the elapsed rescue time.
SETTING THE AED INTERNAL CLOCK The internal clock is preset at Central Standard Time and should be reset to the correct date and local time. The AED will automatically adjust itself for daylight savings time. This feature can be turned off using the ServiceLink software. To set the clock, you will need a PC with Windows 95 or later operating system, RescueLink software installed and a serial communications cable. To set the clock settings:
• • • • • • • •
Open the lid and remove pads from the pads socket.
• •
Reinstall pads per instructions on page 15.
Page 18 of 51
Connect the AED to the PC using the serial communications cable. Ensure that the PC is set at the correct local time and date. Run the RescueLink software on the PC. Verify that the voice prompt states “Communications Mode”. Click Communications on the main menu. Select AED Date and Time. Click on the Get button to review the current time in the AED. If the time and date is incorrect, click Set to set new time and date. The AED date and time will automatically be updated to the PC’s time and date. Disconnect the serial communications cable and close the lid.
Copyright © 2007, General Electric Company
2022105-201 Rev C
Section 2: Getting Started
VOICE PROMPTS AND TEXT DISPLAY The voice prompts activate when the AED lid is opened and help guide the operator through the rescue. The Responder AED text display provides a visual display of most of the audible voice prompts. The following table lists the voice and text prompts and a description of when the prompts are issued.
VOICE PROMPT
TEXT DISPLAY
SITUATION
“Tear Open Package and Remove Pads.”
OPEN PACKAGE AND REMOVE PADS
When the lid is opened, this phrase is repeated twice to initiate the rescue sequence.
“Peel One Pad from Plastic Liner.”
PEEL ONE PAD FROM PLASTIC LINER
Repeats until one pad is peeled off of the liner.
“Place One Pad on Bare Upper Chest.”
PLACE ONE PAD ON BARE UPPER CHEST
Repeat twice while one pad is placed.
“Peel Second Pad and Place on Bare Lower Chest as Shown.”
PEEL SECOND PAD PLACE ON LOWER CHEST
Repeats until both pads are placed on the patient.
“Do Not Touch Patient! Analyzing Rhythm.”
DO NOT TOUCH PATIENT ANALYZING RHYTHM
When the AED is analyzing the cardiac rhythm of the patient.
“Shock Advised.”
SHOCK ADVISED
When the AED is preparing to deliver a defibrillation shock.
“Charging.”
CHARGING
Repeated while AED is charging.
“Stand Clear! Push Flashing Button to Deliver Shock.”
STAND CLEAR PUSH BUTTON TO SHOCK
After the AED is fully charged and ready to deliver the defibrillation shock. The RED Shock indicator flashes and the phrase repeats for 30 seconds or until the Shock button is pushed.
2022105-201 Rev C
Copyright © 2007 General Electric Company
Page 19 of 51