GE Healthcare

TONOPORT V Operators Manual Ver 2.1

Operators Manual

36 Pages

File Type: PDF

File Size: 1 MB

File Name: GE Healthcare - TONOPORT V Operators Manual Ver 2.1.pdf

Preview

Page 1

GE Healthcare

TONOPORT V Ambulatory Blood Pressure System Firmware Version 2.1

Operator’s Manual 2001589-085 ENG

Revision A

Note The information in this manual only applies to TONOPORT V, firmware version 2.1. It does not apply to earlier firmware versions. Due to continuing product innovation, specifications in this manual are subject to change without notice.

CardioSysTM and CASETM are trademarks owned by GE Medical Systems Information Technologies GmbH, a General Electric Company going to market as GE Healthcare. © 2009 General Electric Company. All rights reserved.

TONOPORT V

2001589-085 Revision A

Contents

Application, Safety Information

Controls and Indicators

Setup

Application

Data Output

Error Codes

Software Installation

Cleaning, Maintenance, Disposal

Technical Specifications

Order Information

Appendix - Electromagnetic Compatibility (EMC)

Revision History This manual is subject to the GE Healthcare change order service. The revision code, a letter that follows the document part number, changes with every update of the manual. Part No./Revision

Date

Comment

2001589-085 Revision A

May 2009

Initial release

2001589-085 Revision A

TONOPORT V

General Information

General Information y The product TONOPORT V bears the CE marking

y This manual reflects the equipment specifications and

CE-0482 (notified body MEDCERT GmbH)

applicable safety standards valid at the time of

indicating its compliance with the provisions of the

printing. All rights are reserved for devices, circuits,

Council Directive 93/42/EEC about medical devices

techniques, software programs, and names appearing

and fulfills the essential requirements of Annex I of

in this manual.

this directive. It has an internal power source and is an MDD class IIa device.

y On request GE Healthcare will provide a detailed Service Manual.

y It has a type BF applied part.

y The safety information given in this manual is

y The product fulfills the requirements of the standard

classified as follows:

EN 60601-1 "Medical Electrical Equipment, Part 1: General Requirements for Safety" as well as the

Danger

electromagnetic immunity requirements of the

indicates an imminent hazard. If not avoided, the

standard EN 60601-1-2 "Electromagnetic

hazard will result in death or serious injury.

Compatibility – Medical Electrical Equipment". y The radio-interference emitted by this product is within the limits specified in CISPR11/EN 55011, class B. y

Warning indicates a hazard. If not avoided, the hazard can result in death or serious injury.

The device is classified by CSA INTERNATIONAL and thus also fulfills the UL safety requirements.

y The CE marking covers only the accessories listed in the "Order Information" chapter. y This manual is an integral part of the equipment. It should be available to the equipment operator at all times. Close observance of the information given in the manual is a prerequisite for proper equipment performance and correct operation and ensures

Caution indicates a potential hazard. If not avoided, the hazard may result in minor injury and/or product/ property damage. y To ensure patient safety and interference-free operation and to guarantee the specified measuring accuracy, we recommend only original equipment accessories as available through GE Healthcare distribution. The user is responsible for the

patient and operator safety. Please note that information pertinent to several chapters is given

application of accessories from other manufacturers.

only once. Therefore, carefully read the manual once in its entirety. y The symbol

means: Consult accompanying

documents. It indicates points which are of particular importance in the operation of the equipment.

TONOPORT V

2001589-085 Revision A

General Information

PAR Medizintechnik GmbH Sachsendamm 6 D-10829 Berlin Germany Tel. +49.30.23.50.70.0 Fax +49.30.21.38.54.2

Distributor: GE Medical Systems Information Technologies, Inc. 8200 West Tower Avenue Milwaukee, WI 53223 USA Tel:+1.414.355.5000 800.558.5120 (USA only) Fax:+1.414.355.3790

The country of manufacture appears on the device label.

2001589-085 Revision A

TONOPORT V

Application, Safety Information

1.1 Application Biocompatibility

Intended Use

The parts of the equipment described in this

TONOPORT V is a small-size, patient-borne blood

manual, including all accessories, that come in

pressure monitor for ambulatory, non-invasive

contact with the patient during the intended use,

measurement of the patient’s blood pressure. If the blood

fulfill the biocompatibility requirements of the

pressure cuffs listed in chapter 10 "Order Information" fit

applicable standards if used as intended. If you

the patient, it can be used on adults, children, and small

have questions in this matter, please contact GE

children. TONOPORT V is not suitable for blood

Healthcare or its representatives.

pressure measurements in neonates. Also it is not suitable for use in intensive-care medicine.

Oscillometric Measuring Method

For periods of up to 30 hours, TONOPORT V records the patient's blood pressure at selectable intervals and saves the results. There is a choice of three different measurement protocols.

The blood pressure is measured by the oscillometric method. The criteria for this method are the pressure pulsations superimposed with every systole on the air pressure in the cuff.

Using TONOPORT V with CASETM /

The blood pressure cuff is wrapped around the upper arm

and inflated to a pressure which must be clearly above the

CardioSys

/ CardioSoft

TONOPORT V can be operated in conjunction with CASETM (version 5.15 or later), with CardioSysTM (version 4.14 or later), or with the analysis program CardioSoft (version 4.14 or later) that is included with TONOPORT V. If the USB port is used, it is necessary to install the appropriate driver first (see “Software Installation” on page 22). With these systems, individual measurement protocols can be created and the stored data can be reviewed on-

expected systolic pressure. A pressure transducer measures the cuff pressure as well as the superimposed pressure pulsations. During blood pressure measurements the cuff must be level with the heart. If this is not ensured, the hydrostatic pressure of the liquid column in the blood vessels will lead to incorrect results. y When the patient is sitting or standing during measurements, the cuff is automatically at the correct level.

screen in tabular and graphic form. With V6.5 and subsequent versions, the patient ID used by the analysis program can be stored in TONOPORT V to allow the collected data to be downloaded without selecting the patient first (refer to the respective Operator Manuals; you will find the CardioSoft manual on the CardioSoft CD).

Fig. 1-1 Waveform representing the pressure decrease in the cuff during a measurement: systolic pressure at 131 mmHg, diastolic pressure at 76 mmHg

TONOPORT V

2001589-085 Revision A

Application, Safety Information

1.2 Functional Description The TONOPORT V monitor accommodates the blood pressure measuring system and a microprocessor for system control and data processing. The monitor is powered by two AA size batteries (either rechargeable NiMH batteries or alkaline batteries).

2001589-085 Revision A

TONOPORT V

Application, Safety Information

1.3 Safety Information Warning

Danger

Risk to persons - – Equipment may be connected to other

Risk to persons - – The equipment is not designed for use in areas where an explosion hazard may occur. Explosion

equipment or to parts of systems only when it

hazards may result from the use of flammable

has been made certain that there is no danger to

anesthetic mixtures with air or with oxygen,

the patient, the operator, or the environment as

nitrous oxide, skin cleansing agents or

a result. In those instances where there is any

disinfectants.

element of doubt concerning the safety of connected equipment, the user must contact the manufacturers concerned or other informed experts as to whether there is any possible danger to the patient, the operator, or the environment as a result of the proposed combination of equipment. Compliance with the standard IEC 60601-1-1 must always be ensured. – TONOPORT V may be connected to CASETM, CardioSysTM or to a PC with the CardioSoft program. While connected to any of these devices, TONOPORT V must be disconnected from the patient. – Chemicals required for the maintenance of the equipment, for instance, must under all circumstances be prepared, stored, and kept at hand in their specific containers. Failure to observe this instruction may have severe consequences for the patient. – Liquids must not enter the equipment. Equipment into which liquids have entered must be inspected by a service technician before use. – Before cleaning, TONOPORT V must be disconnected from other equipment (CASETM, CardioSysTM, PC). – Dispose of the packaging material, observing the applicable waste-control regulations. Keep the packaging material out of children's reach.

TONOPORT V

2001589-085 Revision A

Application, Safety Information

Warning

Caution

Incorrect measurements -

Equipment damage, risk to persons -

– Magnetic and electrical fields are capable of

– Before connecting the battery charger to the

interfering with the proper performance of the

power line, check that the voltage ratings on the

equipment. For this reason make sure that

nameplate match those of your local power line.

external equipment operated in the vicinity of

– The battery charger is not a medical device. It

TONOPORT V complies with the relevant EMC

must not be used in the patient environment.

requirements. X-ray equipment, MRI devices, radio systems, etc. are possible sources of

– Before using the equipment, the operator is required to ascertain that it is in correct working

interference as they may emit higher levels of electromagnetic radiation.

order and operating condition. – The operator must be trained in the use of the equipment. – Only persons who are trained in the use of medical technical equipment and are capable of applying it properly are authorized to apply such equipment. – There are no user-replaceable components inside the equipment. Do not open. For service or repair, please contact your local, authorized dealer (http://gehealthcare.com).

2001589-085 Revision A

TONOPORT V

Controls and Indicators

Connection for blood pressure cuff

Button

INFO

: push to display the most recent

parameter readings. Readings appear in the following order:

- systolic value "S" (unit mmHg or kPa shown on the display)

- diastolic value "D" (unit mmHg or kPa shown on P

B N

the display)

T R TA P S TO S

- pulse rate "HR" (unit min-1)

F O

The same button is used - to toggle between the day phase and the night

TO O

P O S

T R

D -1

in /m R H

phase chapter 4, section "Toggle Manually Between Day and Night Phase") and

- to program the BP monitor (chapter 3 "Setup") !

off

0 on

Button START : push to start and stop a STOP measurement, and to confirm entries

6 4

Liquid crystal display (LCD)

Port for connection to PC (USB)

Port for connection to PC (RS232)

Calibration mark

Lid covering battery compartment

(Rechargeable) batteries

Fig. 2-1 TONOPORT V controls and indicators

ON/OFF switch

Functions of the

Nameplate

Button

INFO

Button

Message

Function

on display Push once

clear memory

Push twice

set date and time

Push 3 times

select the measurement protocol

Push 4 times

activate calibration mode

Push 5 times

display firmware version

Push 6 times

select energy source

Push 7 times

enable/disable audio signal

Push 8 times

toggle pressure unit between mmHg and kPa

TONOPORT V

2001589-085 Revision A

Controls and Indicators

Explanation of Signs and Symbols

Date of manufacture.

Symbols used on the equipment and on the packaging

The number found under this symbol is the date of manufacture in the YYYYMM format.

Caution, consult accompanying

Calibration mark, valid in Germany only

documents

(see section "Technical Inspections of the

This symbol indicates that the waste of

Measuring System" in chapter 8)

electrical and electronic equipment must not be disposed as unsorted municipal waste and must be collected separately. Please contact an authorized representative of the manufacturer for information concerning the

Symbols used on the display M

decommissioning of your equipment.

blinks with each detected oscillation; is continuously lit when the monitor contains data

Type BF applied part

blinks when the batteries are almost depleted; is

(defibrillation-proof)

continuously displayed when batteries are discharged and no more BP measurements can

Catalogue number

be taken

Serial number

day phase selected

CE marked per the Medical Device

night phase selected

Directive 93/42/EEC of the European Union. The notified body is MEDCERT GmbH. Gossudarstwenny Standart Russia (GOST) CSA International classification mark

USB port, connection to PC

Serial port, connection to PC

Class II equipment

For indoor use only

Manufacturer’s identification

2001589-085 Revision A

TONOPORT V

Setup

Some Basic Facts on Battery Power

Insert Batteries

TONOPORT V is either powered by two rechargeable Nickel Metal Hydrid batteries (NiMH) or by two alkaline batteries. The device must be set to the power source used (see section "Insert Batteries" below). The device also contains a Lithium cell that powers the clock. The Lithium cell can only be replaced by a service technician.

Note Switch TONOPORT V off before inserting the batteries. To do so, slide the ON/OFF switch (10, Fig. 2-1) to the left while looking at the display. y Hold TONOPORT V as shown in Fig. 3-1 and slide

The capacity of two fully charged or new batteries is

the lid of the battery compartment open (approx.

sufficient for a minimum of 30 hours of operation or for

1 cm).

200 measurements.

It is not possible to open the lid more than about 1 cm

The capacity of rechargeable batteries decreases with

which is just enough to reach the ON/OFF switch. To

age. If the capacity of fully charged batteries is

replace batteries, you must take off the lid (pull upward).

considerably less than 24 hours, the batteries must be replaced.

y Place the two batteries in the compartment as indicated by the symbols.

Caution Equipment damage - – Only use the original rechargeable, size AA Nickel

Select Energy Source y Turn on the BP monitor. The switch is located inside

Metal Hydrid batteries (from manufacturers such

the battery compartment. Slide the switch to the right,

as Sanyo, Panasonic, Energizer, Duracell, Varta,

while looking at the display.

or GP) with a capacity > 1500 mAh or size AA

y Wait for the time to be displayed.

high-rate discharge alkaline batteries (such as Panasonic Evoia, Energizer Ultimate, Duracell

y Push

Ultra, Duracell Power Pix, or Varta maxtech).

INFO START STOP

six times: the display shows "H 6".

INFO

y Push START : the display will show "AAAA" when the STOP

– Charge the NiMH batteries to capacity before using them for the first time.

BP monitor is set up for rechargeable NiMH batteries

– Recharge the NiMH batteries immediately after use and do not leave batteries uncharged.

(as shipped) and "bbbb" when it is set up for alkaline batteries.

– Use only the original charging unit to recharge y Confirm the displayed information with

the NiMH batteries. – Do not attempt to recharge the alkaline batteries.

INFO START STOP

INFO

change the selection with START STOP and confirm the new selection with

INFO START STOP

y Next the BP monitor will briefly display the capacity of the inserted batteries. "A 100", for instance, means that the rechargeable batteries have a capacity of 100%, i.e., they are fully charged. "b 50" means that the alkaline batteries have a capacity of only 50%, i.e., they are half depleted. y Place the lid on the battery compartment and close. Note The energy source needs to be selected only when the BP monitor is put into service for the first time or when you change from NiMH to alkaline batteries and vice versa. Fig. 3-1 Opening the battery compartment 12

TONOPORT V

2001589-085 Revision A

Setup

Charge NiMH Batteries

y If necessary, replace the connector to match the wall outlet type (the charging unit is shipped with the Euro connector):

Caution Equipment damage, risk to patients -

– push the button below the connector and hold it depressed (1, Fig. 3-2)

– The charger is not a medical device. It must not

– remove the connector and insert the suitable type

be used in the patient environment. – The contact surface of the NiMH batteries and of the charger must always be kept clean. – The charger is to be used indoors only and must be protected against oil, grease, aggressive

of connector 2, 3 – ensure that the new connector locks into place. y Connect the cable of the AC power adapter to the charging unit 4 and plug the AC power adapter into the wall outlet.

detergents and solvents to prevent damage. – If the charger is damaged in any way, e.g. after a drop or when the mains pins are bent, the local

y Insert the two batteries into the charging unit, observing the correct polarity.

authorized dealer must be contacted immediately. – High temperatures affect the charging process. Ideally, the room temperature should not exceed 40 °C (104 °F). – After quick charging, please wait for some minutes before another quick charge. Otherwise the temperature sensors will not

COMPIT

function correctly.

TC 4

If TONOPORT V is powered by rechargeable batteries (4 of them are shipped with the equipment), they should be recharged immediately after use (24 hours). Use only the original charger supplied. It consists of an AC power adapter and the charging unit itself. y Check that the voltage ratings on the nameplate of the charging unit match those of your local power line.

Fig. 3-3 Red LEDs on charger The batteries take up to 3 hours to recharge. Each of the red LEDs corresponds to one of the charger compartments (Fig. 3-3). During the charge cycle, the corresponding red LED blinks at a slow rate (approximately once per second). Note: If the red LED does not light up, the battery may be

1 4

inserted the wrong way round. When the battery is charged,

the LED is solid red. The charging unit now trickle-charges

the battery to compensate for self-discharging.

COMPIT

The battery temperature is monitored in the charger.

TC 4

When the temperature is too high, the LED is solid red and the charger switches to trickle-charging. If the battery is correctly inserted and the red LED does not light up, the charger has identified a battery problem. The charging current to the compartment concerned will be cut off. Remove the battery and discard, observing the

Fig. 3-2 Exchanging the connector, connecting the

applicable waste-disposal regulations.

charger 2001589-085 Revision A

TONOPORT V

Setup

Performance Check When turned on, TONOPORT V runs a self-test that

Note

includes all symbols and segments on the LCD (Fig. 3-4).

When using TONOPORT V in conjunction with

Then it checks the batteries and indicates the remaining

CASETM / CardioSysTM / CardioSoft, it is

capacity. "A 100", for instance, means that the

recommended to perform the first three steps at the

rechargeable batteries have a capacity of 100%, i.e., they

PC.

are fully charged. "b 50" means that the alkaline batteries have a capacity of only 50%, i.e., they are half depleted. The minimum battery capacity for a 24-hour

Clear the Memory The symbol M on the display indicates that memory

measurement is 90%.

contains BP data. If these data still need to be analyzed,

If the capacity is below 90%, new or fully charged

refer to chapter 5 "Data Output" for details on data

batteries must be inserted.

evaluation. If you do not need the data any more, delete it

BP monitors that have passed the self-test and completed

as follows:

the battery test will indicate the following information:

y Briefly switch TONOPORT V off and on again and wait for the time to be displayed.

– the time of day – the measuring phase (day

/ night

)

y Push

INFO START STOP

: the display indicates "H 1".

y Push

INFO START STOP

: the display indicates "LLLL".

– whether or not data are stored in the BP monitor (M) (Fig. 3-5). The BP monitor will also emit an audio signal, if enabled.

INFO y To delete the data, push START again: the display indiSTOP

cates "0000", followed by the time (if you do not wish to clear the memory, turn off the BP monitor instead INFO of pushing START ). STOP

kPa

mmHg

Fig. 3-4 Test display on LCD

M Fig. 3-5 Example: display after successful self-test (M= BP data in memory, measuring phase: day) Before using TONOPORT V on a patient 1.

clear the memory

check date and time and correct, if required

select a measurement protocol

enable or disable the audio signal.

TONOPORT V

2001589-085 Revision A

Setup

Time and Date

Measurement Protocols

Usually the BP monitors are set to the correct time and

There is a choice of three different measurement

date before delivery. Therefore, the time only needs to be

protocols:

corrected to change between Standard Time and Daylight Protocol

Saving Time.

Day Phase

Night Phase

(7 a.m. to 10 p.m.)

(10 p.m. to 7 a.m.)

every 15 minutes

every 30 minutes

every 20 minutes

every 40 minutes

every 30 minutes

every 60 minutes

Setting Date and Time y Briefly switch TONOPORT V off and on again and wait for the time to be displayed. INFO

y Push START twice: the display indicates "H 2". STOP

Max. inflation pressure: day phase 250 mmHg night phase 220 mmHg

INFO

y Push START : the display indicates the year, e.g. STOP "2009". INFO

y If the indicated year is correct, confirm it with START STOP or correct it with

INFO START STOP

INFO and confirm with START . STOP

Select a Measurement Protocol y Briefly switch TONOPORT V off and on again and wait for the time to be displayed.

– The display indicates the month, e.g. "03". INFO

y If the indicated month is correct, confirm it with START STOP or correct it with

INFO START STOP

INFO

y Push START STOP three times: the display indicates "H 3". INFO y Push START : the display indicates "LLLL" (Selecting STOP

INFO

and confirm with START . STOP

y In the same manner, correct day, hour and minute.

a protocol automatically clears the memory. If you do

y In the end, the time of day will be displayed again.

off.)

Selecting the Pressure Unit

not wish to clear the memory, turn the BP monitor

INFO y Push START : the display indicates "P1" (protocol 1). STOP

y Briefly switch TONOPORT V off and on again and INFO

y Using START , select protocol 2 or 3 STOP

wait for the time to be displayed. INFO

y Push START eight times: the display indicates "H 8". STOP

OR INFO

y Push

INFO START STOP

: the display indicates "mmHg" or "kPa". INFO

y Confirm the pressure unit with START or select the othSTOP er unit with

INFO START STOP

INFO , then confirm with START . STOP

y Confirm the displayed protocol with START STOP .

Enable or Disable the Audio Signal y Briefly switch TONOPORT V off and on again and wait for the time to be displayed. INFO

y Push START seven times: the display indicates "H 7". STOP INFO y Push START : the display indicates "0000" when the auSTOP

dio signal is turned off, and "1111" when it is turned on. INFO

INFO

y Either confirm the setting with START or press START to STOP STOP INFO

select the alternate setting and confirm with START . STOP

2001589-085 Revision A

TONOPORT V

Application

Symbols used on the cuff

Cleaning the Cuffs – Use a moist cloth to wipe the cuffs clean if they are

Refer to Operator Manual.

only slightly soiled. – Clean cuffs that are heavily contaminated by washing

Cuff suitable for adult patients of

them with soapy water or a suitable cleaning agent

the indicated height (see man in

that contains a disinfectant (do not machine-wash).

box). Adult-sized cuffs are availa-

Ensure that no liquid penetrates into the cuff bladder

ble as standard, small, large and ex-

or the pressure tubing (for this reason, remove the

tra large.

bladder from the cuff before cleaning).

BP cuff suitable for the indicated arm circumference.

– After cleaning, rinse the cuff thoroughly with water and let it dry at room temperature for about 15 hours. – The cuffs can be disinfected with isopropyl alcohol 70%, ethanol 70%, Microzid, Buraton liquid,

BP cuff width.

Sporicidin or Cidex. After disinfection, rinse the cuff thoroughly with tap water and air-dry.

When the cuff is applied, this label must face the skin. When the cuff is applied, these two arrows must be located over the brachial or femoral artery. This line identifies the end of the cuff which must be situated within the range identified by the INDEX label when the cuff is closed.

The end of the cuff must be situated within this range when the cuff is closed.

Latex-free BP cuff.

CE marking, cuff fulfills EU directives.

TONOPORT V

2001589-085 Revision A

Application

Applying the Cuff Warning Risk to persons - Disconnect TONOPORT V from other equipment (CASETM, CardioSysTM, PC) before connecting it to the patient. y Always insert two fully charged NiMH batteries or two new alkaline batteries, before starting a measurement. y Check that the memory has been cleared (see “Clear the Memory” on page 14). y Select the appropriate cuff size (see cuff label). When Fig. 4-1 Applying the cuff

the cuff is too small the BP values will be overrated, when it is too big, the measured values will be too low. Caution Incorrect measurements - – Use only the cuffs listed in chapter 10 "Order Information". – Replace cuffs on a regular basis. Damaged Velcro fasteners may cause incorrect readings.

Index

y Place the cuff on that arm of the patient that is used less frequently during normal daily activities. On adults it should be placed about 2 fingers' breadth above the bend of the elbow; on children, a little closer. Bending the arm must not change the cuff

Fig. 4-2 Applying the cuff

level. Verify that – the cuff tubing points up toward the shoulder (Fig. 4-1) – the side with the

label is on the skin

– the arrow is located above the brachial or femoral artery – the dashed white line at the end of the cuff is located between the two dashed

lines

when you close the cuff (if this is not the case, select another cuff size, Fig. 4-2) – the cuff fits snugly around the arm, but does not compress the blood vessels.

2001589-085 Revision A

TONOPORT V

Application

Initiate a Trial Measurement

Patient Information

y Turn on TONOPORT V and place it in the carrying

Advise your patient

pouch. There is an aperture in the pouch to accommodate the cuff connection tube.

– not to move while a measurement is being taken to avoid motion artifacts that may lead to erroneous

y Attach the pouch to the patient (shoulder strap, belt). For reasons of hygiene, it is not advised to carry the pouch on the bare skin.

readings and to keep the cuff inflation time as short as possible – to place TONOPORT V on the night stand while in

y Guide the pressure tubing around the patient's neck as a strain relief and connect it to the blood pressure cuff port on the TONOPORT V (1, Fig. 2-1). Advise the patient to avoid kinking the tubing during the measurement. y Check that the display indicates the time of day. If the memory contains data from a previous procedure, the letter "M" will appear on the display when you turn on the device. If you still try to initiate a measurement, the message "LLLL" prompts you to clear the memo-

bed – how to switch the device manually from the day to the night phase (see page 19) – that events considered important should be noted down in a diary and that intermediate measurements INFO START

can be initiated with STOP

– that the measurement can be stopped at any time with INFO START STOP

(the cuff will be deflated)

ry. Push START twice to delete the data. If you do not STOP

– not to open the battery compartment

wish to delete the data, turn off the device instead of

– about the audio signal and its meaning.

INFO

pushing START STOP .

Warning

y To avoid erroneous measurements, ensure that the patient does not move during the trial measure-

Risk to persons - Instruct your patient – to terminate the measurement with

ment. The patient may stand or sit.

INFO START STOP

whenever the cuff is not deflated within about

INFO y Push START to initiate the first measurement.

2 minutes,

STOP

Within a few seconds, the device starts inflating the cuff.

– to remove the cuff if it is not deflated after

When the inflation pressure has been reached, the cuff will gradually be deflated. The changing cuff pressure is indicated on the display and the letter "M" appears with each detected oscillation. At the end of the measurement the measured data appears in the following order

INFO

button. This could be due activation of the START STOP to kinked tubing. The cuff must be reapplied as described earlier before additional measurements can be taken.

– the systolic reading (S in mmHg or kPa) – the diastolic reading (D in mmHg or kPa) – the pulse rate (HR/min-1). If an error code, such as "E 29" (insufficient number of oscillations detected) is displayed after the measurement, INFO

tighten the cuff a little and push START again (see also STOP chapter 6 "Error Codes"). If the trial measurement has been successfully completed, the device is ready for automatic measurements.

TONOPORT V

2001589-085 Revision A

Application

General Information on Ambulatory BP Measurement

Toggle Manually Between Day and Night Phase

These are the buttons on TONOPORT V used during an

In the three measurement protocols the day phase lasts from

ambulatory blood pressure measurement:

7 a.m. to 10 p.m. and the night phase from 10 p.m. to 7 a.m. On the display the two phases are represented by the

START STOP

INFO

symbols

starts and stops a measurement displays the most recent measurement results

(day) and

(night).

Patients whose day and night phases are different from INFO

or the most recent error message, toggles

these predefined periods can push the START STOP button twice

between day and night phase (see next section)

to change from one phase to the other.

For the first measurement, the cuff is inflated to a

Note

pressure of 160 mmHg (initial pressure). For subsequent

If the measurement protocol was created with

measurements, the device inflates the cuff to a pressure

CASETM / CardioSysTM / CardioSoft and only 1

which is 15 mmHg above the systolic value of the

BP period has been specified, switching from one

previous measurement (minimum inflation pressure:

phase to the other will leave the measurement

120 mmHg).

intervals unchanged. They will always be the same.

If the measuring value is above the inflation pressure, the

The information "day phase" and "night phase" is

device will increase the cuff pressure another 50 mmHg. A manual measurement can be taken at any time between the automatic measurements. Manual measurements are

only used to identify the measurements.

Audio Signal

identified with the "+" symbol in the tabular BP data.

If enabled (see page 15), the audio signal will be emitted

The device will repeat a measurement after 2 minutes, if

in the following situations:

unsuccessful. An error code referring to failed

– shortly after TONOPORT V was switched on

measurements is generated only after three consecutive

– just before TONOPORT V starts inflating the cuff

unsuccessful measurements.

(during the day phase only)

Error codes E02 (battery depleted), E06 (inflation time over) and E08 (200 measurements taken) do not lead to a

– after TONOPORT V has detected an erroneous measurement

second measurement. The next measurement after error code E06 takes place at the selected interval. After error codes E02 and E08, the device enters the power-save mode to prevent over-discharging of the rechargeable batteries. This mode can only be terminated by turning the device off and on again.

2001589-085 Revision A

TONOPORT V

Data Output

The measurement data are output via CASETM /

For more information about data output, please refer to

CardioSysTM/CardioSoft.

the Operator Manual of CASETM, CardioSysTM, CardioSoft.

Warning

When you have finished downloading data to CASETM /

Risk to persons - While connected to the patient, TONOPORT V

CardioSysTM / CardioSoft and do not intend to continue

must be disconnected from other equipment

working with this system, disconnect TONOPORT V and

(CASE

, CardioSys

turn it off.

, PC).

P T R TA P S TO S

Note

IN F O

If the USB port is used, it is necessary to install the T R O

P O

N TO

appropriate driver first (see “Software Installation”

on page 22).

D HR /m

S in -1

y Put the PC-based system into operation (see CASETM, CardioSysTM or CardioSoft Operator Manual). y Turn off TONOPORT V.

y Connect TONOPORT V to the PC system: – via cable 2001589-040, if the USB port of TONOPORT V is used (a Fig. 5-1) – via cable 2001589-011, if the serial port of Fig. 5-1 Connections for PC cable

TONOPORT V is used (b Fig. 5-1) y Turn on TONOPORT V and wait for the time to be displayed on TONOPORT V.

USB port

RS232 port

TONOPORT V

2001589-085 Revision A

Previous Page Next Page