Progressa Bed Tips Rev 2 Nov 2014

Progressa® Bed Tips FULLCHAIR® POSITION

CONTINUOUS LATERAL ROTATION THERAPY

TO ACTIVATE: • Set the brake • Press and hold the Chair button on the siderail or caregiver pendant* to go into the FullChair® position • The patient deck will slightly recline backwards as the seat and lumbar sections on the mattress slightly deflate • If the footboard is installed, when the articulation stops and a tone sounds, the bed has reached the FullChair® position

NOTE: • If the footboard is not installed, the bed will proceed into Chair Egress

CHAIR EGRESS TO ACTIVATE:

• Rotation provides side-to-side Continuous Lateral Rotation Therapy (CLRT) to aid in the prevention and treatment of pulmonary complications related to immobility

TO ACTIVATE: • Select Pulmonary Therapy control on the GCI • Select Rotation • For pre-set options, select Full, Moderate or Minimum • For custom option, select Custom • Set rotation direction, rotation percentage and duration • Select either Yes or No on rotation training mode • Select Start

• Set the brake • Recommend removal of footboard at this point • Press and hold the Chair button on the siderail or caregiver pendant* to go into the FullChair® position • If the footboard is installed, the bed has reached the FullChair® position when the articulation stops and a tone sounds • NOTE: If the footboard is not installed, the bed will proceed into the chair egress position • Required removal of footboard at this point • Press and hold the Chair button until the bed lowers completely • Seat Deflate will activate to lower the patient • Bed will beep 3 times indicating the surface is deflated • Hold Chair again to proceed to Chair Egress position • The bed tilts and then the knee lowers

OPTIONAL EGRESS ASSISTANCE:

TO ACTIVATE:

• Hold Chair again to inflate back section for egress assist   

• On the home screen, select the Surface tab • Select Max Inflate • Confirmation

TO ACTIVATE: • Raise or lower the bed so the patient’s feet will be flat on the floor • Press the Side Exit Assist button, located on head end siderail, until the indicator light turns green • The surface will begin to inflate under the patient • Once the patient reaches their ideal egress position, assist the patient with bed exit

TO DEACTIVATE: • Press the Side Exit Assist control on the head end siderail

TO ACTIVATE: • Select the Pulmonary Therapy control on the GCI • Select P & V • For pre-set options, select High, Medium or Low • For custom option, select Custom • Set Percussion intensity • Set Vibration intensity, frequency and duration • Select Start

MAX INFLATE • Maximizes the firmness of the primary section of the patient surface. The bed will stay in Max Inflate for 30 minutes before returning to normal/standard state

–– On the home screen, the Max Inflate icon will be highlighted when activated

TO DEACTIVATE: • Select the Surface tab on the home screen • Select Normal • Select the Max Inflate button on the upper side rail control

TURN ASSIST - RIGHT

BOOST® POSITIONING SYSTEM

TO ACTIVATE: • Press the Surface tab • Press the Patient Comfort tab • Use the Comfort Adjustment controls to change the pressure in the head, seat, and heal section of the mattress –– To increase the pressure, press the Up arrow –– To decrease the pressure, press the Down arrow

• The bed exit alarm will notify the caregiver of activities including: –– Out of Bed: patient’s weight shifts significantly off the frame of the bed

–– Position: patient moves toward either siderail or moves away from the head section, such as sitting up in bed

TO ACTIVATE: • Ensure patient is centered on the bed and aligned with the hip indicator • Select the Alarms tab • Select the Bed Exit tab • Select Position, Exiting or Out of Bed • If you change your selection the GCI will arm • The home screen will then display Bed Exit On and highlight icon

SLEEP MODE • Sleep Mode is used to reduce frequency of air system adjustments for patients who are sensitive to air surface movements • After 8 hours the Normal mode reactivates

TO ACTIVATE: • Press the Surface tab on the GCI • Press the Sleep Mode control

TO DEACTIVATE: • Press the Surface tab on the GCI • Press the Normal control

ZERO/NEW PATIENT

• To return to the flat position, press and hold the Bed Flat control. If the bed has an air system, press the Normal control for the surface

–– Once turn assist is initiated, you may lower a siderail to facilitate patient care –– The bed will alarm as a safety precaution

TO ACTIVATE:

• Select the Surface tab on home screen • Select the Normal control

–– Bed Exit: Time spent with the Bed Exit alarm ON –– Scale: Weight increase or decrease in 24-hour periods

TO ACTIVATE: • Make sure the patient is not in bed • Put bed in required position • Press the Scale control on the GCI • Press Zero

PRESS: NEW PATIENT • Erases Scale History • Zeroes the scale • Returns surface to Normal mode • Turns off RemindMe reminders

PRESS: ZERO • Does not erase Scale History • Zeroes to scale

©2014 Hill-Rom Services, Inc. ALL RIGHTS RESERVED. ENG – US

USA 800-445-3730 CANADA 800-267-2337

• Make sure the patient is in the center of the bed • Press the Scale tab • Press Weigh Patient and follow on-screen instructions • You will be prompted to put the bed into the recommended position • ‘Green’ screen indicates recommended position is achieved • Press Continue • Note: You can weigh the patient if the bed is not in recommended position • You will be prompted to remove all items hanging on the bed frame • Once patient is weighed, press Accept to move on or Re-weigh to redo the weighing process

–– Head Angle: Time spent with the head of bed more than 30⁰ or 45⁰ since 12am

–– Siderails must be in the up position to activate turn assist

TO DEACTIVATE:

www.hill-rom.com

TO WEIGH THE PATIENT:

• Press the Preference tab on the GCI • Press History • Select the desired history to display:

• Assists caregiver in turning the patient for linen changes, dressing changes, bed panning, back care, and other nursing procedures

–– On the home screen, the Right Turn Assist icon will be highlighted when active

185826 rev 2 03-NOV-2014

• Make sure the patient is not in the bed • Press the Scale tab • Press Zero the Bed and follow on-screen instructions

TO VIEW PATIENT HISTORY:

• Select the Surface tab on home screen • Select the Right Turn Assist tab (patient’s right) • Confirmation

Hill-Rom reserves the right to make changes without notice in design, specifications and models. The only warranty Hill-Rom makes is the express written warrantyextended on the sale or rental of its products.

TO ZERO THE SCALE:

PATIENT HISTORY

TO ACTIVATE:

TIP:

USING THE SCALE (NON OIML)

–– Exiting: patient moves away from the center of the bed towards an egress point

• The Boost® Positioning System assists with the movement of the patient to the head end of the bed • Press and hold the Boost® control on the siderail • The bed will transition to the Trendelenburg position • If the bed has an air system, the mattress will go into Max Inflate for 30 minutes • Release the Boost® control when the desired position is reached • Reposition the patient as needed

PATIENT COMFORT • Adjust the firmness of the surface to meet the comfort levels of the patient

PERCUSSION & VIBRATION • Percussion & Vibration helps loosen secretions in the lungs and helps move lung secretions for easier removal

SIDE EXIT ASSIST

BED EXIT ALARM

FOR COMPLETE INSTRUCTIONS ON HOW TO OPERATE THE PROGRESSA® BED, SEE USER’S MANUAL.

–– Rotation: The maximum number of cycle/hour the patient has rotated and Hrs: Mins in rotation, in 24 hours –– P & V: The number of treatments provided per 24-hour period –– OPTI-REST™: Time spent in OPTI-REST mode since 12am –– Chair: Time spent in Chair position since 12am

WEIGHT HISTORY TO VIEW THE WEIGHT HISTORY: • Press Scale tab • Press History tab • Icons will provide information based on: –– Initial weight –– Weight taken in recommended position –– Weight taken in non-recommended position