KH 402 HOME-CARE Lifter Operating, Maintenance and Cleaning Manual KEIM-012

INDEX

PAGE

SPECIFICATIONS

2

SPARE PARTS

3-4

SAFETY PRECAUTIONS

5

OPERATING INSTRUCTIONS

5

BATTERY CHARGING AND CARE

6

MAINTENANCE INSTRUCTIONS

7

CLEANING INSTRUCTIONS

8

SPECIFICATIONS DIMENSIONS:

KH402

Length Width Height Effective lift range Leg gating (inside) Lift reach Under base clearance Base height

1150mm 670mm 1220mm 430mm – 1700mm 510mm – 900mm 700mm 25mm 110mm

Leg height from floor Turning radius

100mm 1300mm

LIFT SPEED:

35mm per second

LIFT DRY WEIGHT:

38 Kg (with battery)

LIFT CAPACITY:

Max load - 150kg

CASTORS:

Ø125mm Total lock rear polyurethane castor Ø75mm Twin swivel grey rubber castors – front. Note: Larger castors available on request. (Easier to move)

FINISH:

Epoxy powder coated Polyurethane yoke

ELECTRICAL ITEMS:

Tested by Linak Australia to standards:- AS 3108-1990 - AS 3200.1-1990

2

HOME-CARE LIFTER

KH402

3

HOME-CARE LIFTER

KH402

4

HOME-CARE LIFTER

SAFETY PRECAUTIONS. 1. The Home – Care hoist is manufactured and tested with safety and function for the carer and patients as the utmost importance. 2. The MAXIMUM safe working load is 150 Kg’s. 3. EMERGENCY LOWERING: The emergency lowering button can be used to lower the hoist if there is a handset failure. The switch is located on the controller under the big red emergency stop switch. Simply press using a ballpoint pen or similar object, DO NOT use a sharp object such as a compass point. 4. Always use the correct slings on the hoist. 5. For safety precautions only properly trained personal should use the hoist.

OPERATING INSTRUCTIONS BATTERY PACK INSTALLATION Simply locate the battery on the mounting bracket and clip the release lever into the secure position. The Hoist is now ready for use.

HANDSET: - RAISE/LOWER: The hoist operates via a hand controller. To raise or lower the hoist, simply press the required switch on the touch pad. LEG GATING: To OPEN or CLOSE the “Gate” on the legs, simply press the foot pedal to open or close the legs.

KH402

5

HOME-CARE LIFTER

YOKE - SLING MOUNTING POINTS Refer to the fitting instructions supplied with the sling.

BATTERY CHARGING AND CARE CHARGING: Before the hoist can be operated the battery pack will need to be charged. Minimum 4 hours for flat battery. Please follow the instructions below. Plug the charger unit into the 240 Volt supply outlet. The unit is now ready to accept a battery that requires charging. To charge the battery, simply locate the charging plug securely into the female socket on the base of the battery. If a two-battery system is going to be used, replace the first battery once charged, with the second battery. Charge as above. NOTE: A battery pack may remain on charge indefinitely without any detrimental effects to the battery or charging unit.

BATTERY CARE: The hoist uses fully sealed lead acid batteries. They are made to be recharged on a regular basis. To care for your batteries and obtain the maximum life DO NOT allow the batteries to run totally flat before recharging. The controller is fitted with an audio low battery warning alarm. When this warning alarm sounds complete the lift process, then change the battery and recharge. Kerry Equipment recommends that a 2-battery system be used, this allows one battery to always be on charge while the other is in use, and hence the hoist may never be out of service with a flat battery.

KH402

6

HOME-CARE LIFTER

MAINTENANCE INSTRUCTIONS The hoist requires periodical lubrication. These points are: CASTORS. It is always best practice to remove all hair and lint from the castors as soon as possible, always allowing free movement of all the wheels. The head bearing will need lubricating monthly. Simply spray TAC-2 up into the bearing while rotating the castor. The wheel also requires lubricating every month. To do this the wheel must be unbolted and removed from the castor frame. TAC-2 can then be sprayed into the hub centre to lubricate the internal bearings.

BASE PIVOT POINTS and FOOT PEDAL All pivot points will need to be lubricated regularly with TAC-2 or similar lubricant. Simply spray the points for a second or two on either side. The hoist has to be turned onto its side for access to the following lubrication points. (To do this 2 people are required.) Both people are to stand on one side of the hoist. One near the push handle, the other by the side of the hoist. The person near the push handle locks the total lock castors. In conjunction with one another, pull the hoist towards the side, lowering the hoist onto the floor. You now have access to all the lubrication points under the base. i.e.: pivot points, leg lever and leg pivot. Simply spray TAC-2 on all the pivot points.

KH402

7

HOME-CARE LIFTER

ARM AND ACTUATOR PIVOT POINTS The arm and actuator pivot points will need to be lubricated regularly with TAC-2 or similar lubricant. Simply spray on each side of the recommended points for a second or two.

TAC-2 is a CRC product and is available from most automotive outlets or from Kerry Equipment. KERRY EQUIPMENT NOW HAS A SERVICE VAN FOR ALL YOUR MAINTENANCE NEEDS CALL: 08 9240 2944

CLEANING INSRUCTIONS 1.

The hoist can be cleaned with a low strength detergent, warm water and a soft textured cloth. This includes all Epoxy powder coated framework and yoke.

2.

CAUTION Do not immerse any parts in water. Do not allow water/cleaning liquid to enter the battery or controller. Clean up spills immediately.

3.

SLING CARE Protect from direct sunlight. Repair any cuts or fraying immediately. Slings are machine washable. Please refer to care instructions on the sling.

Distributed by: -

KH402

8

HOME-CARE LIFTER