Quick Guide
4 Pages
Preview
Page 1
QUICK GUIDE ENGLISH
Author: Tomi Lonka (Desigence)
ument name: GUI Flowchart TA031 Document name: GUI Flowchart Document name:TA031 GUI Flowchart TA031 ame: GUI Flowchart TA031 0.1 ument number: TA031-GUI Document number: TA031-GUI Document number: TA031-GUI umber: TA031-GUI sion: 04 Revision: 04 Revision: 04 e: 11.14.2017 Date: 11.14.2017 Date: TURNING THE TONOMETER ON11.14.2017 AND LOADING THE PROBE 017 hor: Tomi Lonka (Desigence) Author: Tomi Lonka (Desigence) Author: Tomi Lonka (Desigence) Lonka (Desigence) 1. Press the Select or Measure button to turn the tonometer on. Illustrations of these alternative ways of starting: (Remember to use the wrist strap)
Document name: GUI Flowchart TA031 0.1 1.0 0.1 0.2 Document number: TA031-GUI 1.0 16/03/2017 Revision: 04 16:36:10 Date: 11.14.2017 MEASURE Author: Tomi Lonka (Desigence) MEASURE
1.0
MEASURE
0.1 0.2
16/03/2017 017 16:36:10 10
D
1.2
Pressing the Select button to start 1.1 OD 0.2 1.1 0.3
1.2 EYE
16/03/2017
16/03/2017
16:36:10
16:36:10 LOAD
OS1.2
1.3
LOAD
ID 91.4 1.3 9 2. Open the probe tube byIDremoving the cap 16/03/2017 probe base LOAD and insert the probe into the LOAD as shown in the image. 16:36:10 OD
1.5
ID 9
EYE 0.3
OD OS EYE
EYE
ID 9
OD
1.8
EYE
ID 9
1.4
1.3
ID 1.5 9
1.1
ID 9
1.0
OD OS OD LOAD LOAD EYE
1.5 1.3
1.1 1.4
ID 9
ID 91.6 ID 9 ID 9
ID the 9 Play-symbol 3. When appearsOS onID the9display, select OD
between the OD (right eye) and the OS (left eye) by EYE pressing the Navigation buttons, or leave without selecting the eye. The tonometer is ready to perform OS OD OS OS ODOS OS OD OD OD LOAD ODmeasurements. OS OD OS OD
EYE
EYE
ID 1.8 9
ID 9 1.8 ID 9
EYE
EYE
1.6
ID 9 1.7
OS
0.3
OD
LOAD
Pressing the Measure button to start
0.3 1.3 0.2
1.0
1.7
ID 9
OS
1.3
OD
1.9
OD
EYE EYE EYE
1.4 1.7
OS OS
OD
EYE EYE
Ready to measure. Eye side selection: OD, no information, OS. 1.9
ID 9
ID 9 ID 9
ID 9
1.7
EYE
ID1.9 9
ID 9
17.6 17.6
OD mmHg 1.10
OD mmHg
ID 9
2.4
1.10
1.10
Icare ic200 tonometer Quick Guide
ID 9
ENGLISH
23.9
OD mmHg 4. Ensure that the forehead support is fully extended by turning the forehead support adjustment wheel. The distance from the tip of the probe to the patient’s cornea (see picture below) should be about 5 mm (about 3/16 inch). Bring the tonometer in front of the patient’s eye with the1.11 probe pointing IDto 9 the center of the cornea until the forehead support touches the forehead. Keep the probe horizontal and pointing perpendicularly to the center of the cornea. Adjust the probe-cornea distance for your patient by turning the forehead support adjustment wheel. A patient’s IOP can be measured in the supine position as well as in upright (sitting or standing) positions. Do not accidentally push the or ODtonometer mmHg probe into the eye.
20.8
1.12
ID 9
16.5
OD mmHg
1.13
1
OD
ID 9
17.6
~5 mm (3/16”)
OD mmHg
1.14 and hold the Measure1.15 5. Probe will contact the eye during measurements: Press button to collect ID 9
6 measurements in a row OR Press the button briefly 6 times to collect 1 measurement at the time. The grey segments of a circle on the display screen will turn blue one by one.
23.8
17.4
ONE SHORT BEEP Indicates a correct single measurement.mmHg
12
OD mmHg
DOUBLE BEEP Indicates an incorrect single measurement. (See error messages from full manual). LONG BEEP Indicates that six succesful measurements are done and IOP result is available at the display.
16.5
17.4
mmHg
mmHg
DISPLAY DURING MEASUREMENTS ID 9
1.16
16.5
OD mmHg Before
After the second measurement
After the sixth measurement
After the sixth measurement but with acceptable 1.17 variation
REPEAT After the sixth measurement but with too much1.18 variation
12
PARTS OF THE TONOMETER 1. Forehead support 2. Probe base 3. Locking collar
1. 5.
4. Display screen 5. Adjustment wheel for forehead support
2.
6. User interface Navigation buttons
3.
4.
6.
7. Select button
7.
8. Measure button
8.
CHANGE THE PROBE BASE REGULARLY TO AVOID UNNECESSARY SERVICE. REPLACING THE PROBE BASE 1. Turn power off from the tonometer. 2. By hand, unscrew the probe base collar and place it in a safe location. 3. Pull the probe base out of the tonometer using thumb and fingers. 4. Insert a new probe base into the tonometer. 5. Screw the collar down until it firmly locks the probe base.
Please refer to the manual for additional information.
TA031_048_EN_3.0
www.icaretonometer.com