Operating Instructions
16 Pages
Preview
Page 1
Original operating instructions
Refrigerator Read the operating instructions before switching on for the first time
Page 14
EN
LKUv 1610 LKUv 1613
7085 960-01
Content
Priority of warnings... 14 Safety instructions and warnings... 14 Symbols on the appliance... 15 Intended use... 15 Foreseeable incorrect use... 15 Declaration of conformity... 15 Noise emissions from the appliance... 16 Climate rating... 16 Description of the appliance... 16 Other features... 16 Setting up... 16 Levelling the appliance... 16 Electrical connection... 17 Operating and control elements... 17 Switching the appliance on and off... 17 Setting the temperature... 17 Temperatur display mode... 17 Door open alarm... 18 Setting the delay time for the door open alarm... 18 Audible warning signal settings... 18 Deactivating the audible warning signal function... 18 Alarm test... 18 Alarm messages... 19 Adjusting the alarm parameters... 19 Calling up stored alarm events and reading the temperature progression... 19 Resetting the stored alarm events HAn... 19 Resetting the recorded temperature progression rt ... 19 Example of an alarm query...20 Calibrating the control sensor...20 Product sensor ...20 Calibrating the product sensor ...20 Switching the temperature display between control sensor and product sensor... 21 Keypad lock... 21 Setting the real time clock... 21 Conversion from summer to winter time... 21 Enabling/disabling automatic conversion from summer to winter time...22 Changing the network address ...22 Resetting the parameters to factory settings...22 Safety lock...22 Interior light...22 Defrosting...22 Setting the display indication for the defrost phase...22 Activating the defrost function manually...22 Cleaning...23 Disposal notes...23 Shutting your appliance down...23 Malfunctions...23 Possible error messages in the display...23 External alarm... 24 Installation dimensions (mm)... 24 Changing over door hinges...25
Priority of warnings DANGER
identifies a situation involving direct danger which, if not obviated, may result in death or severe bodily injury.
WARNING
identifies a dangerous situation which, if not obviated, may result in death or severe bodily injury.
CAUTION
identifies a dangerous situation which, if not obviated, may result in minor or medium bodily injury.
NOTICE
identifies a dangerous situation which, if not obviated, may result in damage to property.
Note
identifies useful information and tips.
Safety instructions and warnings
- WARNING: do not seal ventilation openings on the appliance housing or enclosure.
- WARNING: only use the mechanical devices or other aids recommended by the manufacturer to help speed up the defrosting process.
- WARNING: do not damage the refrigerant circuit. - WARNING: do not use any electrical devices in the refrigerator compartment which do not comply with the design recommended by the manufacturer.
- WARNING: the mains cable must not be damaged while installing the appliance. - WARNING: multi-sockets or distributor strips and other electronic devices (such as halogen transformers) must not be positioned and operated at the rear of appliances.
- WARNING: danger of injury through electric shock. There are live parts under the cover. Only have the interior LED light replaced or repaired by customer service staff or trained personnel. - WARNING: risk of injury from the LED lamp.The light intensity of the LED light complies with laser class RG 2. If the cover is defective, do not look directly at the light through optical lenses from close distance. This may damage your eyes. - WARNING: this appliance must be secured as described in the operating instructions to rule out any potential risks due to its instability.
14
- This appliance can be used by children of 8 years old and over, and also by persons with restricted physical, sensory or mental capacity or lack of experience and knowledge, if they are supervised or have been instructed on safe use of the appliance and understand the resulting risks. Children must not be allowed to play with the appliance. Cleaning and user maintenance must not be carried out by children without supervision.
- Do not store any explosive substances, such as aerosol containers with flammable propellant gas, inside the appliance. - To prevent injury and damage to property, the appliance should only be installed by two people.
- After unpacking it, check the appliance for signs of damage. Contact the supplier if it is damaged. Do not connect the appliance to the mains power supply. - Avoid prolonged skin contact with cold surfaces (e.g. chilled/frozen products). If necessary, take safety action (e.g. gloves). - All repairs and work on the appliance may only be carried out by customer service personnel or other trained personnel. The same applies to changing the mains power cable.
- Only carry out repair and other work on the appliance when the mains plug has visibly been disconnected.
- Only install, connect and dispose of the appliance as described in these operating instructions.
- In the event of a fault, pull out the plug or switch off the fuse. - When disconnecting the appliance from the mains, pull on the plug. Do not pull on the cable. - Do not use the interior LED light to light the room. The interior LED light is only designed to illuminate the interior of the appliance. - Do not allow naked flames or ignition sources to enter the appliance.
Symbols on the appliance
EN
The symbol can be located on the compressor. It refers to the oil in the compressor and indicates the following danger: swallowing or inhaling can be fatal. This is only relevant for recycling. There is no danger in normal operation. Warning about inflammable substances.
A sticker to this effect may be applied to the rear of the appliance. It refers to the foampadded panels in the door and/or the housing. This is only relevant for recycling. Do not remove the sticker.
Intended use
This universal laboratory refrigerator for professional use is suitable for storing products at temperatures between 3°C and 16°C. Typical products for storage include research samples, reagents, laboratory inventory, etc. For the storage of valuable or temperature-sensitive substances or products the use of an independent, constantly monitoring alarm system is necessary. This alarm system must be designed so that each alarm status is detected immediately by an authorised person who can then take appropriate action.
Foreseeable incorrect use
Do not use the appliance for the following applications: • Storage and cooling of
- chemically unstable, inflammable or caustic substances - blood, plasma or other bodily fluids for the purposes of infusion, application or insertion into the human body.
• Use in potentially explosive atmospheres.
• Use outdoors or in areas where it is exposed to splash water or damp conditions. Incorrect use of the appliance will result in damaging or spoiling the goods stored in it.
Declaration of conformity
The refrigerant circuit has been tested for leaks. The appliance complies with the relevant safety regulations and EU Directives 2006/42/EG, 2014/30/EU, 2009/125/EG and 2011/65/EU.
15
Noise emissions from the appliance
The noise level while the appliance is operating is below 70 dB(A) (relative noise level 1 pW).
- Maximum/minimum interior temperatures are stored.
- Last 3 temperature alarms are saved with time, date and duration of alarm.
- Last 3 power cuts are saved with time, date and duration of power cut. - Safety thermostat to avoid temperatures below +2°C.
The climate rating is indicated on the type plate. Max. room temperature
Max. relative humidity
4
30 °C
55%
7
35 °C
5
- Audible and visual door open alarm.
- Serial interface (RS485) for external temperature and alarm documentation.
The climate rating indicates at what room temperature the appliance may be operated to achieve full cooling capacity and what the maximum humidity level in the area around the appliance may be to ensure that no condensation forms on the exterior housing.
3
- Audible and visual temperature alarm. - Floating contact for connection to a remote monitoring system.
Climate rating
Climate rating
Other features
25 °C
40 °C
60% 40% 75%
The minimum room temperature at the place of installation is 10°C.
Description of the appliance
It is essential to use these safety facilities to avoid damage to stored items. These facilities must not be deactivated or decommissioned!
Setting up
• Do not place the appliance in direct sunlight or near radiators and similar sources of heat.
• The more coolant there is in the appliance, the larger the room in which the appliance is installed must be. If the room is too small, any leak may create a flammable mixture of gas and air. For each 8 g of coolant the installation space must be at least 1 m³. Information on the coolant is on the model plate inside the appliance. • Always install the appliance directly against the wall.
Levelling the appliance
Compensate floor unevenness using the adjustable feet.
NOTICE
The appliance must be aligned horizontally and vertically. If the appliance is not level, the main body of the appliance can be deformed and the door will not close properly.
Appliance dimensions
(1) Operating and control elements (2) Interior light (LED light strip) (LKv 1613) (3) Type plate (4) Grid shelves (5) Adjustable-height feet
NOTICE
The maximum load per grid shelf is 45 kg.
16
Electrical connection
Switching the appliance on and off
The permissible voltage and frequency are indicated on the type plate. The position of the type plate is shown in the section entitled Description of the appliance.
Switching the appliance on
Only operate the appliance with alternating current (AC).
EN
Connect the appliance to the mains. Display = OFF. Press
for approx. 5 seconds. Display = ON.
The socket must be properly earthed and protected by a fuse. The tripping current of the fuse must be between 10 A and 16 A.
No alarm is displayed or sounded when the appliance is switched on for the first time.
The socket must not be situated behind the appliance and must be easily accessible.
If the appliance is disconnected from the mains for a long time after it has been switched on for the first time and if the temperature inside the appliance rises above the upper alarm limit, this will be detected as a fault by the electronic control system ( flashes in the display).
Do not connect the appliance using an extension cable or extension socket. Do not use stand-alone inverters (conversion of direct current to alternating current/threephase current) or energy-saving plugs. Risk of damage to the electronic control system!
When the appliance is switched on again, this display must be reset as shown below.
Operating and control elements
Press
.
Press
+
The
LED will now light up permanently.
Press
for 5 seconds.
for 5 seconds. Display =
The electronic control system will switch back to normal operating mode. On/Off button (switching the appliance on and off) Selection buttons Defrost button (for manually activating the defrost function) Keypad lock Button for calling up stored alarm events Audible alarm Off button Enter button
Switching the appliance off Press
Setting the temperature Press
Compressor is running LED flashing - refrigeration unit switches on after a delay. The compressor will start automatically after the pressure in the refrigerant circuit has equalised. Fan is running Appliance is defrosting Temperature display via product sensor is activated
for 1 second. The temperature display flashes.
To increase the temperature (warmer): press button To reduce the temperature (colder): press button Press
Symbols in the display
for approx. 5 seconds. Display =
. .
again.
The desired temperature setting is saved.
Note
The temperature in the warmest area of the interior may be higher than the temperature setting. If the door is left open for a lengthy period, the temperature in the appliance's compartments may rise dramatically.
Temperatur display mode
LED flashing and appears in the display. The real time clock must be reset.
The temperature display can be switched between degrees Celsius and degrees Fahrenheit. Factory setting is degrees Celsius.
The display means that the power supply and interior temperature of the appliance are recorded.
Press
for 5 seconds. Display =
Press
. Display =
If flashes in the display, there has either been a power failure or the temperature in the appliance exceeded the permissible range. Alarm function The appliance has suffered a fault. Contact the customer service department.
Use button
or
to select the desired setting.
0 = °C
1 = °F
Press
. Display =
Press
for 5 seconds.
The electronic control system will switch back to normal operating mode. 17
Door open alarm
When the door is opened, the LED display begins to flash.
lights up and the temperature
When the door has been left open for more than 60 seconds, the LED begins to flash, and and the temperature indication flash alternately in the display. The audible warning signal sounds (unless the audible warning signal function has been deactivated). If the door has to stay open for longer in order to insert items to be cooled, cancel the audible warning signal by pressing button .
Setting the delay time for the door open alarm
The time before the audible warning signal sounds after the door has been opened can be adjusted. Press
for 5 seconds. Display =
Press
until
Press
. Display =
Use button
appears in the display.
or
Setting range = 1 - 5 minutes. to select the desired setting.
Press
. Display =
Press
for 5 seconds.
The audible warning signal function can be completely deactivated if necessary. Press
for 5 seconds. Display =
Press
until
Press
. Display =
Use button
appears in the display. or
to select the desired setting.
0 = audible warning signal function activated 1 = audible warning signal function deactivated Press
. Display =
Press
for 5 seconds.
The electronic control system will switch back to normal operating mode.
Alarm test
This test checks the function of the internal and any external connected alarm device. The appliance does not stop its refrigerating function during this test.
The electronic control system will switch back to normal operating mode.
Audible warning signal settings
Press
+
for 5 seconds.
• The display will change to a temperature value of 0.2°C below the set upper alarm limit. • The temperature value will now rise by 0.1°C every 2 seconds.
The audible warning signal will be muted for the current alarm after the button has been pressed. Complete the following steps if you want the audible warning signal to reactivate automatically.
• When the upper alarm limit is reached,
Press
for 5 seconds. Display =
Press
until
• The temperature value will continue to rise up to 0.2°C above the upper alarm limit.
Press
. Display =
Press
. Display =
Press
. Display =
appears in the display.
will appear in the
display. An external alarm unit connected to the floating alarm output will now be activated.
• The same process will take place automatically for the lower alarm limit.
The LED
will appear in the display.
will be lit during the test.
Automatic reactivation of the audible warning signal is now active.
The electronic control system will switch back to normal operating mode.
The time before the audible warning signal sounds again must be set.
Cancelling the test prematurely
Press
. Display =
Press
Press
. Display =
Use button
or
Setting range = 1 - 120 minutes.
to select the desired setting.
Press
. Display =
Press
for 5 seconds.
The electronic control system will switch back to normal operating mode.
18
Deactivating the audible warning signal function
for 5 seconds.
Note If the values of the upper and lower alarm limit (AL and AH in the section entitled "Adjusting the alarm parameters") are set to 0, and will appear in the display during this test. Note For a realistic temperature alarm test, an additional delay time (60 minutes) applies as well as the adjustable alarm parameters AL, AH and Ad. After a door has been opened or a defrosting process, the alarm delay Ad will be extended by an additional delay time (60 minutes). This additional delay time must not be changed. This means that a temperature alarm will appear later after a door has been opened or a defrosting process than is actually set using parameter Ad.
Alarm messages
1. LED
flashes in the display
If appears in the display, the appliance has a fault. Consult your nearest customer service point. 2. LED
EN
Calling up stored alarm events and reading the temperature progression Press
Scroll through the list using
The interior is too warm (HI) or too cold (LO).
Last temperature alarm but one Temperature alarm before
Note The alarm parameters can be adjusted. See Adjusting the alarm parameters.
Number of power cuts Last power cut
flashes in the display
Last power cut but one
There has been a power cut (HF) of some length or the interior was too warm or too cold (HA) during a certain period of time.
Power cut before
Up to three alarm events can be stored and called up.
Period in hours in which the maximum and minimum interior temperatures were measured
Adjusting the alarm parameters
Note After a door has been opened or a defrosting process, the alarm delay Ad will be extended by an additional delay time (60 minutes). This additional delay time must not be changed. This means that a temperature alarm will appear later after a door has been opened or a defrosting process than is actually set using parameter Ad. Press
for 5 seconds. Display =
Press
until
appears in the display.
= Lower alarm limit Press
. Display = temperature difference in °C
Use button
or
to select the desired setting.
Set positive values only. Press
. Display =
Press
. Display =
Press
. Display = temperature difference in °C
Use button
or
Upper alarm limit
to select the desired setting.
.
Last temperature alarm
The audible warning signal sounds (unless the audible warning signal function has been deactivated).
The alarm limits (difference to the set temperature) and the alarm delay (delay until alarm sounds) can be adjusted.
or
Number of temperature alarms
flashes in the display; the display reads HI or LO
3. HA / HF /
. Display =
Maximum (highest) measured temperature Lowest measured temperature Select the required item using the again to return to the list.
button. Press this button
You can exit the menu at any time by pressing
for 5 seconds.
If no button is pressed within 60 seconds, the electronic control system switches back automatically.
Resetting the stored alarm events HAn Press
. Display =
Press
+
Press
for 5 seconds.
for 5 seconds. Display =
.
The electronic control system will switch back to normal operating mode.
Resetting the recorded temperature progression rt Press
. Display =
Press the button
or
until
appears in the display.
Set positive values only.
Press
. Display =
Press
. Display =
Press
for 5 seconds. Display =
Press
. Display =
Press
. Display = alarm delay in minutes
The values for and (highest and lowest measured interior temperature) are then reset to the current interior temperature.
Use button
or
to select the desired setting.
Press
. Display =
Press
for 5 seconds.
Press
.
for 5 seconds.
The electronic control system will switch back to normal operating mode.
The electronic control system will switch back to normal operating mode. 19
Example of an alarm query Situation: HA/HF/
flashes in the display.
Press
. Display=
Press
. Display =
There has not been an alarm status with a too high or too low temperature. You must switch to display .
Calibrating the control sensor (standard sensor for
temperature control)
Possible tolerances of the control sensor (the displayed temperature compared to the actual interior temperature) can be offset with this function.
Press
for 5 seconds. Display =
Press
until
. Display = correction value set at the factory
appears in the display.
Press
. Display =
Press
Press
until
Press
. Display = 1 power failure has occurred.
Use button or to increase or decrease the correction value in 0.1°C increments.
Press
. Display =
Press
. Display =
Press
. Display =
(year)
Press
. Display =
(month 1-12)
Press
. Display =
(day 1-31)
Press
. Display =
(hour 0-23)
Press
. Display =
(minute 0-59)
Press
. Display =
(period of time in minutes)
Press
+
The
LED will now light up permanently.
appears in the display.
Last power failure.
. Display = actual (corrected) interior temperature
Press
. Display =
Press
for 5 seconds.
The electronic control system will switch back to normal operating mode.
Product sensor
The product sensor in the bottom area of the appliance interior is an additional sensor for temperature indication.
for 5 seconds. Display =
HA/HF is cancelled in the display. The electronic control system is now ready for the next alarm. Press
Press
for 5 seconds.
The electronic control system will switch back to normal operating mode.
Calibrating the product sensor
Possible tolerances of the product sensor (the displayed temperature compared to the actual interior temperature) can be offset with this function. Press
for 5 seconds. Display =
Press
until
Press
. Display =
appears in the display.
Use button or to increase or decrease the correction value in 0.1°C increments. Press
. Display = actual (corrected) product sensor temperature
Press
. Display =
Press
for 5 seconds.
The electronic control system will switch back to normal operating mode.
20
Switching the temperature display between control sensor and product sensor
Press
for 5 seconds. Display =
Press
until
Press Press
Setting the real time clock
The real time clock is preset (CET). For a different time zone, the time must be adjusted manuall. Press
for 5 seconds. Display =
. Display = (control sensor)
Press
. Display =
. Display =
Press
. Display =
Press
. Display =
appears in the display.
(product sensor)
If the product sensor is activated,
appears in the display.
(year)
Press
. Display =
Set the year by pressing the
Press
for 5 seconds.
Press Press
The electronic control system will switch back to normal operating mode.
Keypad lock
The keypad lock ensures that no unintentional changes are made to the electronic control system.
EN
. Display =
buttons. Press
(month 1-12)
. Display =
Set the month by pressing the Press
. Display =
Press
. Display =
buttons. Press
Set the day by pressing the
buttons. Press
Press
for 5 seconds. Display =
Press . Display = (days of the week) (1 = Monday, 7 = Sunday)
Press
until
Press
Press
. Display =
Use button
or
Press
. Display = . Display =
. Display =
Press
Press
for 5 seconds.
Set the hour by pressing the
Activating the keypad lock
Press
for 5 seconds. Display =
Use button Press
or
to select the PIN code.
. Display =
All buttons except
buttons. Press
and
are locked.
Press
. Display =
Press
. Display =
buttons. Press
.
(minute 0-59)
Set the minutes by pressing the Press
.
(hour 0-23)
Press
The electronic control system will switch back to normal operating mode.
.
. Display =
Set the day of the week by pressing the to choose a PIN code between 1 and 999.
.
(day 1-31)
Setting a PIN code for the keypad lock function appears in the display.
.
buttons. Press
.
for 5 seconds.
The electronic control system will switch back to normal operating mode. When
appears in the display, the real time clock must be
If an incorrect PIN code is entered, the electronic control system switches back to normal operation without activating the keypad lock.
reset.
Deactivating the keypad lock
Conversion to summer time is carried out automatically by the electronic control system on the last Sunday in March at 2 o’clock in the morning.
Use button
Conversion to winter time is carried out automatically by the electronic control system on the last Sunday in October at 2 o’clock in the morning.
Press
Press
for 5 seconds. Display = or
to select the PIN code.
. Display =
All functions are enabled. If an incorrect PIN code is entered, the keypad lock remains active.
Conversion from summer to winter time
In order to enable the new time, the appliance must be switched off and on after each of the times specified above.
21
Enabling/disabling automatic conversion from summer to winter time
Press
for 5 seconds. Display =
Press
until
Press
. Display =
Use button
or
to select the desired setting. 1 = activated
Press
. Display =
Press
for 5 seconds.
The electronic control system will switch back to normal operating mode.
Changing the network address
When connecting several appliances via the RS485 interface, each appliance must have its own network address. Press
for 5 seconds. Display =
Press
until
Press
. Display =
appears in the display.
or
to change the network address (1-207).
Switch on switch, the interior light comes on.
Defrosting
The appliance defrosts automatically.
Setting the display indication for the defrost phase
Press
for 5 seconds. Display =
Press
until
Press
. Display =
Use button
appears in the display.
or
to select the desired setting.
Press
. Display =
+ alternating display of and the current tem0 = Symbol perature in the interior of the appliance.
Press
for 5 seconds.
1 = Symbol
+ temperature before the start of the defrost phase.
2 = Symbol
+
The electronic control system will switch back to normal operating mode.
Press
.
. Display =
Resetting the parameters to factory settings
Press for 5 seconds. The electronic control system will switch back to normal operating mode.
Pull out the mains plug.
Activating the defrost function manually
The alarm limits and sensor calibration values can be reset to the factory settings using this function.
Display =
If the door has been left slightly open for a long time, a layer of ice may form in the interior and on the cooling plate. The defrost function can then be activated manually.
Press
Press
Keep
pressed and connect the mains plug.
. Display =
The electronic control system will switch back to normal operating mode.
Safety lock
The lock in the appliance door is equipped with a safety mechanism.
Locking the appliance
• Insert the key as shown by arrow 1. • Turn the key 90°. To unlock the appliance, the same procedure must be repeated in the same order.
22
(LED light strip)
appears in the display.
0 = deactivated
Use button
Interior light
for 3 seconds. Display =
+
The electronic control system will automatically switch back to normal operating mode. Display =
Cleaning
WARNING Before cleaning, always disconnect the appliance from the mains. Pull out the plug or switch off the fuse. WARNING Risk of electrostatic discharge. Only clean plastic parts with a damp cloth! CAUTION Risk of damage to the appliance components and risk of injury due to hot steam. Do not use steam cleaning equipment to clean the appliance. NOTICE All surfaces in the appliance must be cleaned at regular intervals! • Clean the inside, equipment parts and outer walls with lukewarm water and a little detergent. Do not use chemical solvents or any cleaning agents containing sand or acid. • To avoid short-circuits, ensure no cleaning water penetrates into the electrical components when cleaning the appliance. • Dry all parts well with a cloth.
• The dust should be removed from the refrigeration unit and heat exchanger - metal grid at the back of the appliance - once a year. • Do not damage or remove the type plate on the inside of the appliance. It is very important for servicing purposes.
Disposal notes
The appliance contains reusable materials and should be disposed of properly - not simply with unsorted household refuse. Appliances which are no longer needed must be disposed of in a professional and appropriate way, in accordance with the current local regulations and laws.
Malfunctions
You may be able to rectify the following faults by checking the possible causes yourself: • Appliance does not function: – Is the appliance switched on? – Is the plug correctly fitted in the mains socket? – Is the fuse intact? • The temperature is not low enough: – Is the temperature setting correct (see "Setting the temperature")? – Does the separately installed thermometer show the correct reading? – Is the ventilation system working properly? – Is the appliance set up too close to a heat source? • Temperature alarm test does not work as required. – See „Alarm test“ and „Adjusting the alarm parameters“ If none of the above causes apply and you cannot rectify the fault yourself, contact the nearest customer service department stating the type designation 1, service number 2 and appliance number 3as indicated on the type plate. The position of the type plate is shown in the section entitled Description of the appliance.
Possible error messages in the display Error code
E0, E1, E2, rE EE, EF dOr HI
Do not damage the refrigerant circuit of an appliance that is no longer needed during its disposal.
LO
This appliance contains inflammable gases in the refrigerant circuit and insulation foam.
Etc
Your local council or a waste disposal contractor can provide information about how to dispose of the appliance correctly.
HF, HA
Shutting your appliance down
If the appliance is left empty for a lengthy period, it must be switched off, defrosted, cleaned and dried and the door is to be left open to prevent mould formation.
EN
AFr
Error
Action
Temperature sensor defective
Contact the customer service department
Electronic control system error
Contact the customer service department
Temperature inside appliance too high (too warm)
Check that the door has been closed properly. If the temperature does not drop, contact the customer service department.
Appliance door open for too long
Close appliance door
Temperature inside appliance too low (too cold)
Contact the customer service department
There has been a power cut of some length or the interior was too warm or too cold during a certain period of time.
See Calling up stored alarm events and reading the temperature progression
Reset the real time clock (see "Setting the real time clock")
Temperature around Contact the customer the product sensor service department < 0°C
23
External alarm
Installation dimensions (mm)
There are various connection options at the back of the appliance.
Version 1
The appliance may only be connected to an external alarm device by trained personnel.
A cross-section of min. 200 cm2 is required in the worktop for ventilation of the rear of the appliance.
Note The connectors are secured with screws. To remove the connectors, undo the left and right screws.
Floating alarm output Connection to RS485 interface
Product sensor
Terminating resistor When connecting several appliances via the RS485 interface, the terminating resistor must remain on the last appliance. Remove the terminating resistors from the appliances in between.
Floating alarm output
These three contacts can be used to connect the appliance to an optical or acoustic alarm device. The connection is designed for a maximum of 42 V/8 A DC from a safety extra-low voltage (SELV) source (minimum current: 150 mA).
Notice
When supplying mains voltage to the floating alarm contact, the technical safety requirements of standard EN 60335 will not be satisfied.
N.O
Connection for a visual warning light or an acoustic alarm signal.
N.C
Connection for a control lamp to indicate that the appliance is in normal mode.
COM
External power supply unit, 42 V/8 A DC maximum, Minimum current: 150 mA
RS485 interface Rx- / Tx- Send/Receive data cable
(negative pole)
Rx+ / Tx+ Send/Receive data cable (positive pole) GND Earth cable
24
Version 2
If no ventilation grille is provided in the worktop, the recess must be at least 860 mm high to ensure adequate heat dissipation to the front.
EN
Changing over door hinges 1. Unscrew the hinge bracket.
Note
The door mounting has a spring mechanism enabling the door to close by itself. The hinge bracket turns to the left when the screws are undone.
9.
Screw on the handle.
9
2. Pull the door out at the bottom and lift off.
3. Transfer plugs to the other side.
10. Push on pressure plates until they engage.
3
10
4. Transfer pin on hinge bracket to the opposite side.
4
5. Transfer upper hinge
components to the opposite side.
5
6
6. Transfer covers to the opposite side.
7. Mount door on hinge pin and close.
8. Insert hinge bracket in lower
door mounting. Turn hinge bracket by 90° - spring is compressed. Screw on hinge bracket.
7 8
25