Viking M mobile lift Instructions for Use rev 4

Table of Contents

Symbol Description... 3 Safety Instructions... 4 Definitions... 5 Technical Data... 5 Dimensions... 6 EMC Table... 7 Assembly... 9 Operation... 11 Charging the Battery... 14 Maximum Load... 15 Recommended Lifting Accessories... 15 Troubleshooting... 17 Recycling Instructions... 17 Cleaning and Disinfection... 18 Inspection and Maintenance... 20

7EN137107 Rev. 4 • 2020

2

www.hillrom.com

Symbol Description

These symbols can be found in this document and/or on the product. Symbol Description For indoor use only. The product has extra protection against electric shock (Insulation Class II). Protection level against electric shock Type B. Warning; this situation requires extra care and attention Read instructions for use before use This product complies with EC directives.

IP N1 N 2

Protection level against: ingress of solid objects (N1) and ingress of water (N2). Manufacturer Date of manufacture. Caution! consult instructions for use Consult instructions for use for more information Battery

,

Pb

All batteries in this product must be recycled separately. - Pb underneath the symbol indicate batteries containing lead - Single Black line underneath the symbol indicate this product have been placed on the market after 2005.

,

UL Recognized Component Mark for Canada and the United States EFUP, Environmental Friendly Usage Period (years) Environmentally-friendly product which can be recycled and reused. The Australian Safety/EMC PSE Mark (Japan) Product Identifier Serial Number Medical Device Recyclable The safety and essential performance of medical electrical equipment Proof of Product compliance to North American safety standards Non-ionizing electromagnetic radiation GS1 Data Matrix Barcode that may contain following information (01) Global Trade Item Number (11) Production Date (21) Serial Number Duty cycle for non-continuous operation.

X% Y%

≤Tmin

The maximum active operation time X% of any given time unit, followed by a deactivation time, Y%. The active operation time shall not exceed the specified time in minutes, T.

7EN137107 Rev. 4 • 2020

3

www.hillrom.com

Safety Instructions

Intended use This product is not intended to be used by the patient alone. Lifting and transferring a patient shall always be performed with the assistance of at least one caregiver. This product is used as a means to perform the lift but is not in contact with the patient; therefore we do not go into the various patient conditions in this manual. Contact your Hill-Rom representative for support and advice. Certain environments and conditions can limit the correct us of the mobile lifts, including: Thresholds, unlevel floor surfaces, various obstacles, and extra-thick carpets. These environments and conditions can cause the wheels of the mobile lift not to roll as intended, possible imbalance in the mobile lift, and increased exertion by the caregiver. If you are uncertain that your care environment fulfils the requirements for correct use of the mobile lift, please contact your HillRom representative for further advice and assistance. Unbalanced lifting poses a tipping risk and may damage the lift equipment! Never leave a patient unattended during a lifting situation! Do not raise the lift arm manually! Before use, make sure that: • the lift is assembled in accordance with the assembly instructions; • the lifting accessory is properly attached to the lift; • the battery has been charged for at least 6 hours; • you have read the instructions for use for the lift and lifting accessories; • personnel using the lift are informed of the correct operation and use of the lift. Before lifting, always make sure that: • the lifting accessories are not damaged; • the lifting accessory is correctly attached to the lift; • the lifting accessory hangs vertically and can move freely; • the lifting accessory is selected appropriately, in terms of type, size, material and design, with regard to the patient’s needs; • the lifting accessory is correctly and safely applied to the patient in order to prevent injuries; • the latches are intact; missing or damaged latches must always be replaced; • the sling’s strap loops are correctly connected to the sling bar hooks when the sling straps are stretched up but before the patient is lifted from the underlying surface. Incorrect attachment of sling to slingbar may cause severe injury to the patient!

Viking™ M mobile lift have been tested by an accredited testing institute. No modification of this product is allowed. Use of the product adjecent to other equipment should be avoided because it could result in improper operation, if such use is neccessary, observe and verify that the other equipment is operating normally. Electromagnetic disturbance, may affect the lifting performance of the product. Modification using other parts than original spare parts (cables etc.) may affect the electromagnetic compatibility of the product. Particular care must be taken when using powerful sources of electromagnetic disturbance, such as diathermy, etc, so that, for example, diathermy cables are not positioned on or near the lift. If you have questions, please consult the responsible assistive device technician or the supplier. The product may not be used in areas where flammable mixtures may occur, for example, in areas where flammable goods are stored. This Caution notice is found on the Battery: CAUTION! NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL DO NOT SHORT CIRCUIT USE THE SPECIFIED CHARGER ONLY MAY EXPOLODE IF DISPOSED IN FIRE This Caution notice is found on the Control box: CAUTION! NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL 7EN137107 Rev. 4 • 2020

4

www.hillrom.com

Definitions Viking (M)

1. Lift arm 2. Outer Tube 3. Flexlink 4. Sling Bar with latches 5. Lift Mast 6. Emergency Lowering Device (mechanical) 7. Lift Motor (Actuator) 8. Base 9. Front wheels 10. Rear wheels with brakes 11. Motor for base-width adjustment 12. Locking handles 13. Product decal 14. Control box with; Emergency stop Electrical Emergency Lowering Electrical Emergency lifting Battery charger indicators Information display 15. Battery 16 Handcontrol 17. Handles 18. *Optional accessory: Holder for Quick Reference Guide and color code for sling sizes. 19. Color code for sling sizes

1

19 18*

3

2 17

4

BATTERY

ON

16

5 6

15 14

7

13

CHARGE

12

8

11 10

Forward direction

9

Technical Data Maximum load:

205 kg (450 lbs.)

Material:

Aluminium

Total weight:

30 kg (66 Ibs.) excl battery

Weight of heaviest part:

15.2 kg (33.5 Ibs.)

Wheels:

Front: 75 mm (3 inch) twin wheels Rear: 75 mm (3 inch) twin wheels with brake.

Batteries:

Lead-acid gel, valve-regulated battery - 24 V 2.9 Ah Prod. No. 2006106 Weight 2.8 kg (6.2 Ibs.). Li-ION battery - 25.6 V 2.25 Ah Prod. No. 2006109 Weight 0.970 kg (2.14 lbs).

Battery charger:

Internal charger,, 100-240 V AC, 50-60 Hz, max 400 mA.

Lift motor:

Permanent magnet motor with mechanical safety mechanism 24 V, 10.5 A

Turning diameter: 1400 mm (55.2 inch) Emergency lowering device:

Mechanical and electrical

Lifting interval:

1270 mm (50.0 inch)

Lifting speed (no load)

36 mm/s (1.4 inch/s)

Sound level:

46 dB(A)

Protection class:

IP X4

Operating Forces of Controls:

Handcontrol: 5 N

Electrical data:

24 V

Intermittent power:

Int. Op 10/90, active operation max 2 min. Only 10% of a given length of time may be active, but no more than 2 min.

7EN137107 Rev. 4 • 2020

Motor for basePermanent magnet motor width adjustment: 24 V, 6 A Surrounding functional environment:

Temperature: +10°C to +40°C (50° F to 104°F), Humidity: 20% to 90% at 30°C non-condensing, Air pressure: 700HPa to 1060HPa, Altitude: max. 3000m.

The device is intended for use indoors Type B, in accordance with the electrical shock protection class. Class II equipment.

5

www.hillrom.com

Dimensions Top view

Lateral view

M

N

C

**600 mm (24 in)

Amin.

O Lmin

D

**700 mm (28 in)

Amax. Lmax

D1

E F

F1

D2

Max. reach position of lift arm B3 B2 B1 B Max. reach position of lift arm

Viking M

Measurements: mm / inch

Amax.*

Amin.*

2020 1970 1920

1440 1390 1340

B

B1

B2

1230

870

660

79.5 77.6 75.6

56.7 54.7 52.8

48.4

34.3

26.0

B3*** 650 650 595 25.6 25.6 23.4

max.

C

min.

max.

1110

690

970

43.3

27.2

38.2

D

D2**

E*

560

195

1100 1050 1000

22.0

7.7

43.3 41.4 39.4

min.

F

F1

Lmax*

Lmin*

M

N

O

105

30

1790 1740 1690

520 470 420

385

220

495

4.2

1.2

70.5 68.5 66.5

20.5 18.5 16.5

15.2

8.7

19.5

Note: The measurements are based on the lift being equipped with standard sling bar. When changing to other lifting accessories, check that the lift still achieves desired lifting height. * Different measurements apply to Viking M depending on the height-setting position, see “Assembly”. **

Reference measurement according to Standard EN ISO 10535:2006.

7EN137107 Rev. 4 • 2020

6

www.hillrom.com

EMC Table Guidance and manufacturer’s declaration – electromagnetic emissions The mobile lift is intended for use in the electromagnetic environment specified below. The customer or the user of the Viking M lift should assure that it is used in such an environment. Emissions test

Compliance

RF emissions CISPR 11

Group 1

RF emissions CISPR 11

Class B

Harmonic emissions IEC 61000-3-2

Complies

Voltage fluctuations/ flicker emissions IEC 61000-3-3

Complies

Electromagnetic environment - guidance The Viking M lift uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment. The Viking M lift is suitable for use in all establishments including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.

Guidance and manufacturer’s declaration – electromagnetic immunity The mobile lift is intended for use in the electromagnetic environment specified below. The customer or the user of the Viking M lift should assure that it is used in such an environment. Immunity test

IEC 60601 test level

Compliance level

Electromagnetic environment - guidance

Electrostatic discharge (ESD) IEC 61000-4-2

+/- 8 kV contact +/- 15 kV air

+/- 8 kV contact +/- 15 kV air

+/- 8 kV contact +/- 15 kV air Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30 %.

Electrical fast transient / Burst IEC 61000-4-4

+/- 2 kV for power supply lines +/- 1 kV for input/output lines

+/- 2 kV for power supply lines n/a. for input/output lines

Mains power quality should be that of a typical commercial or hospital environment.

Surge IEC 61000-4-5

+/- 1 kV differential mode +/- 2 kV common mode

+/- 1 kV differential mode n/a. for common mode

Mains power quality should be that of a typical commercial or hospital environment.

Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11

0 % UT for 0,5 cycle, at 0, 45, 0 % UT for 0,5 cycle, at 0, 90, 135, 180, 225, 270 and 45, 90, 135, 180, 225, 270 315 degrees and 315 degrees

Mains power quality should be that of a typical commercial or hospital environment. If the user of the [Equipment or System] requires continued operation during power mains interruptions, it is recommended that the [Equipment or System] be powered from an uninterruptible power supply or battery.

Power frequency (50/60 Hz) magnetic field IEC 61000-4-8

0 % UT for 1 cycle, at 0 degrees

0 % UT for 1 cycle, at 0 degrees

70 % UT for 25 cycles at 50 Hz and 30 cycles at 60 Hz, at 0 degrees

70 % UT for 25 cycles at 50 Hz and 30 cycles at 60 Hz, at 0 degrees

0 % UT for 250 cycles at 50 Hz and 300 cycles at 60 Hz.

0 % UT for 250 cycles at 50 Hz and 300 cycles at 60 Hz.

30 A/m

Complies

Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment

NOTE UT is the a.c. mains voltage prior to application of the test level.

7EN137107 Rev. 4 • 2020

7

www.hillrom.com

Guidance and manufacturer’s declaration – electromagnetic immunity The mobile lift is intended for use in the electromagnetic environment specified below. The customer or the user of the Viking M lift should assure that it is used in such an environment. Immunity test

IEC 60601 test level

Compliance level

Electromagnetic environment - guidance Portable and mobile RF communications equipment should be used no closer to any part of the Viking M lift, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance

Conducted RF IEC 61000-4-6

6 Vmrs 150 kHz to 80 MHz

6 Vmrs

Radiated RF IEC 61000-4-3

10 V/m 80MHz to 2,7GHz

10 V/m

d = 1,2 P

d = 1,2 P 80 MHz to 800 MHz d = 2,3 P 800 MHz to 2,7 GHz

where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less than the compliance level in each frequency range. b Interference may occur in the vicinity of equipment marked with the following symbol.

NOTE 1 At 80MHz and 800MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflected from structures, objects and people. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the Viking M lift is used exceeds the applicable RF compliance level above, the Viking M lift should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the Viking M lift. a

b

Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 10 V/m.

7EN137107 Rev. 4 • 2020

8

www.hillrom.com

Recommended separation distances between portable and mobile RF communications equipment and the Viking M lift The mobile lift is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the Viking M lift can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the Viking M lift as recommended below, according to the maximum output power of the communications equipment. Rated maximum output power of transmitter (W)

Separation distance according to frequency of transmitter (m) 150 kHz to 80 MHz

80 MHz to 800 MHz

800 MHz to 2.7 GHz

d = 1,2 P

d = 1,2 P

d = 2,3 P

0.01

0.12

0.12

0.24

0.1

0.38

0.38

0.73

1

1,2

1.2

2.3

10

3,8

3.8

7.3

100

12

12

23

For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.

Assembly Before assembly, make sure you have the following parts: • Lift mast with lift arm, lift motor incl. cable, sling bar and control box with handcontrol • Base with motor for base-width adjustment, incl. cable

• Locking handles • Battery • Instructions for use, charger cable, charger connector cable.

low position standard position high position

1. L ock both rear wheels. Place the lift mast in the foot of the base.

2. The lift mast has three height setting positions; - low position for lower lifting heights. - standard position recommended in most cases. - high position for extra high lifting height. The distance between two holes is 50 mm (2 in). See chapter "Dimensions" for measurements.

3. S ecure the lift mast with the locking handles provided. Adjust the position of the locking handles so that they point downwards.

Motor for base adjustment.

Handcontrol Lift motor

4. Connect cables to the control box, see illustration. Make sure plugs are fully seated. 7EN137107 Rev. 4 • 2020

9

5. Connect the battery and secure it to the control box bracket. A click sound can be heard when the battery is installed correctly. www.hillrom.com

BATTERY

ON

6. Optional accessories: - Quick reference guide - Holder for Quick reference guide.

7. Hang the handcontrol on the handle.

CHARGE

8. Reset the emergency stop by turning the button clockwise.

BATTERY

A

B ON

C

CHARGE

9. A) Connect the extension cable for the charging cable to the control box. B) Insert the extension cable in the tension clip underneath the control box. C) Connect the charging cable to the extension cable. NOTE! Always charge the battery before using the lift the first time, See chapter “Charging the Battery”.

10. Place the charger cable on the hook provided on the mast after completed charging.

After assembly and charging, ensure that: • the battery has been fully charged • lift arm motions correspond with the buttons on the handcontrol • service interval is activated! Push following buttons on the handcontrol simultaneously: Up / Down , until a audio signal (single beep) is heard = service interval activated. (Alternatively use the push buttons simultaneously for emergency lifting up and down on the control box) • base width adjustment correspond with the buttons on the handcontrol • emergency lowering works properly (mechanical and electrical) • Rear wheel brakes, functions properly. The lifting height can be affected when lifting maximum load during in-run of actuator (up to 10 lifts).

7EN137107 Rev. 4 • 2020

10

www.hillrom.com

Operation

4

3

2

kg/lbs

Indicator: 1 - 4

1

kg/lbs

Push buttons: Lift arm: Up / Down Push buttons: Base width: Out / In

Handcontrol operation and indicators Operate the lift using the push buttons on the handcontrol. For raising and lowering: Directional arrows show the direction of movement (up/down) The lifting and base movement stops as soon as the push button is released. Indicator: 1 - 4 1 - Overload (Kg/Ibs) light "flashes yellow", too much load is applied to the lift. 2 - Green light, battery power (100 - 50 %), Ok! - will constantly light up green when charger is connected to mains. 3 - Yellow light, battery power (50 - 25 %), battery needs charging 4 - Yellow light, battery power (Less than 25 %), battery needs charging. A buzzer will sound when pressing a push button. Note! If the buzzer sound starts during an ongoing lift complete the lift and charge the lift afterwards! 4 - Light "flashes yellow" and a buzzer will sound when pressing a push button. Charge the lift immediately! The remaining battery power can only make the lift arm go down. Note! Please see chapter "Charging the Battery" for more information.

Cable

BATTERY

1

2

3

4

5 ON

CHARGE

6

Control Box operation and information 1. Emergency Stop button - Activate: Push the red button - Reset: Turn the red button clockwise. 2. UP (Arrow), Electrical emergency lifting. 3. DOWN (Arrow), Electrical emergency lowering. Operation of the push buttons 2 and 3 are done by pressing with a narrow object into the circle mark above each (Arrow). The Actuator movement stops as soon as the push button is released. 4. "ON" - lights up green when the charger is connected to mains.* 5. "CHARGE" - lights up yellow constantly during charging and will turn off when charging is completed. 6. Display Pop-up information: Battery power (100 - 50 %) Ok! Battery power (50 - 25 %) Battery needs charging. Battery power (Less than 25 %) battery needs charging. A buzzer will sound when pressing a push button. Note! If the buzzer sound starts during an ongoing lift complete the lift and charge the lift afterwards! Charge the lift immediately! A buzzer will sound when pressing a push button. The remaining battery power can only make the lift arm go down. The lift is connected to the mains. SHORT CIRCUIT

!

CHECK CONNECTION

kg/Ibs.

service

7EN137107 Rev. 4 • 2020

Short circuit warning! check cables and connections. Warning is shown until repaired! Overload! Too much load is applied to the lift. Service needed; contact Hill-Rom. 11

www.hillrom.com

6. Information display: Activate information display by a "quick press" at a UP, push button. xxxxx Total number of lift cycles with load AxS xxxxxx Work done by actuator; Amp. x Sec. xxx kg/Ibs. Number of overload indications xx/xxx Days since last service/Days between services. service

Li-ION battery - specific information Sleep mode! the sleep mode will be activated in a Li-ION battery if not in use or charged in one week or more. The sleep mode switches off the battery and it´s electronics to save power. The battery will stay in sleep mode until the battery is set back to operation mode again. How to set the Li-ION battery back in operation mode; Charge the battery, when the "CHARGE" indicator, 5 is lit the battery has been set back in operation mode and ready for use. Note! We recommend to charge the battery until charging is completed, see "Charging the Battery" for more information and instructions. Delay! a delay to indicators for current battery power at the control box and hand control occurs if the emergency stop function is activated and restored, see 1 above. BATTERY

BATTERY

BATTERY

RGE ON CHA

ON

CHARGE

ON

CHARGE

ON

To activate the emergency stop: Push the red Emergency Stop button on the control box. To reset the emergency stop: Turn the button clockwise.

Mechanical Emergency Lowering Enabling the emergency lowering - Lift the emergency lowering control straight up, lift until the patient being lifted is on a firm surface, and the strap loops of the sling can be unhooked. (the function requires a load applied to the lift arm).

CHARGE

Electrical emergency lowering / lifting Use a narrow object to press into the circle mark above each (Arrow), See chapter "Operation" for more information. Do not use sharp objects, since this may cause damage on the control box!

90000 2 M

Unlock Lock

Locking the Wheels The rear wheels can be locked to prevent rotating and turning. The locking/unlocking of the wheels is done with the foot. NOTE: When lifting, the wheels should be unlocked so that the lift can be moved to the patient’s centre of gravity. The wheels should be locked, however, if there is a risk of the lift rolling into the patient, for instance, when lifting from the floor. Locked wheels during lifting can increase the risk of tipping. 7EN137107 Rev. 4 • 2020

Do not raise the lift arm manually!

Never move the lift by pulling on the actuator!

Namn: Dekal Skyddsrör Art. nr: 900002568 Mått (ytterkant tryckt cirkel): (Ø 46 mm) Ilustration, 100% Svart 12Färgkoder: Cirkel, Röd (PMS 185 C), www.hillrom.com Övrig info: Trycks på genomskinlig rund bakgrund (IP 5700 V

Figure 1. Installation of Latches After installation, ensure that the spring loaded latches is taut against the sling bar and moves freely in the sling bar hook.

Figure 2.

Figure 3.

Lift correctly! Before each lift, make sure that: – the Sling loops at opposite sides of the Sling are at the same height – all the Sling loops are fastened securely in to the Slingbar hooks – the Slingbar is level during the lift, see Figure 1. If Slingbar is not level (see Figure 2) or if the sling loops is wrongly attached to the slingbar (see Figure 3) lower the user to a firm surface and adjust according to the instructions for use of sling in use. An improper lift can be uncomfortable for the user and cause damage to the lift equipment! (see Figure 2 and figure 3).

Armrest To use the armrest you need to rotate it from the (vertical) rest position up to the (horizontal) support position. The armrest have two purposes: to help the patient feel more secure and facilitate for the caregiver when moving the lift. When using the lift to transfer a patient between rooms, the armrest should be set in the support position!

Position of the Lift when Lifting From/To:

Bed

7EN137107 Rev. 4 • 2020

Chair/Toilet Seat

13

Floor

NOTE: Place a pillow under the patient’s head for increased performance and comfort. Always have the wheels locked when lifting from the floor.

www.hillrom.com

Charging the Battery

Charger information 1. "ON" - lights up green when the charger is connected to mains. 2. "CHARGE" - lights up yellow constantly during charging and will turn off when charging is completed.

1.

2.

ON ON

CHARGE CHARGE

NOTE! Charging a deep discharged Li-ION battery When charging a deep discharged Li-ION battery the charger will start charging at a low charging rate to protect the battery. During the low rate charging the charge indicator will not light up. When the low rate charging is completed the charger will automatically switch to normal charge rate and the "CHARGE" indicator will light up yellow and will turn off when charging is completed. Charging with the control box internal charger (standard) Plug the charger cable into mains (100-240 VAC), see charger information 1 - 2 above. The battery is fully charged after about 6 hours and the charger disconnects automatically, the yellow "CHARGE" diode turn off. For maximum battery life, batteries must be charged regularly. We recommend charging after each use or every night.

ON CHARGE

Never charge batteries in a wet area! NOTE! • If the charger cable (coiled cable) is streched out it should be replaced to avoid the risk of the cable getting caught and tear. • The lift cannot be used when the charger cable is plugged into a wall socket. • If the yellow "CHARGE" diode at the control box continuos to be lit after 8 hours, discontinue charging and replace the battery with a new one. • A damaged battery shall be replaced and contact with leaking fluids shall be avoided. • If the lift is not used every day, we recommend pushing the emergency stop after use, in order to turn off the power and conserve battery life. Make sure the battery is completely charged before pushing the emergency stop. • The lift cannot be charged with the emergency stop activated.

Alternative charging procedures Alt. A

Alt. B

ON

ON

CHARGE

CHARGE

Wallmounted charger accessory or table charger housing accessory: Loosen the holder for the charger cable. Remove the battery pack from the control box by loosening the locking device on top of the battery pack. See chapter "Assembly". Charger information; "ON" - lights up green when the charger is connected to mains. "CHARGE" - lights up yellow constantly during charging and will turn off when charging is completed. Alt. A. Place the battery pack on the wallmounted charger. Plug the charger cable into mains (100-240 VAC) check that both "ON" and "CHARGE" on the charger lights up. Alt. B. Place the battery pack on the charger in the table charger housing. Plug the charger cable into mains (100-240 VAC) check that both "ON" and "CHARGE" on the charger lights up.

7EN137107 Rev. 4 • 2020

14

www.hillrom.com

Maximum Load Different maximum loads may apply to different products on the assembled lift unit, sling bar, sling and any other accessories used. For the assembled lift unit, the maximum load is always the lowest maximum load rating for any of the components. For example, a Viking™ M mobile lift which is approved for 205 kg (450 lbs) can be equipped with a lifting accessory which is approved for 200 kg (440 lbs). In this case, the maximum load of 200 kg (440 lbs) applies to the assembled lift unit. Study the markings on the lift and lifting accessories or contact your Hill-Rom representative if you have any questions.

Recommended Lifting Accessories Using lifting accessories other than those approved can entail a risk. Find generally recommended sling bars and accessories for Viking™ M mobile lift described below. When changing sling bar or other lifting accessories, the highest possible lifting height of the lift is affected. Before changing lifting accessories you should always ensure that the lift, after change, can fulfil the desired lifting height in order to manage the lifting situations for which the lift is to be used. For additional guidance in selecting a sling, study the instructions for use for the respective sling models. There you will also find guidance for combining Liko™ sling bars with Liko slings. Contact your Hill-Rom representative for advice and information on Liko’s product range.

* this product is also available in a version with Quick-Release Hook. Prod. No. 3156074

Universal SlingBar 450* (Standard on Viking™ M mobile lift) Max. 300 kg (660 lbs)

Prod. No. 3156075

Universal SlingBar 600* Max. 300 kg (660 lbs)

Prod. No. 3156076

Universal TwinBar 670* Max. 300 skg (660 lbs)

Prod. No. 3156077

Universal SideBars 450 including bag Max. 300 kg (660 lbs)

Prod. No. 3156079

Sling Cross-bar 450* Max. 300 kg (660 lbs)

Prod. No. 3156021

Sling Cross-bar 670* Max. 300 kg (660 lbs)

Prod. No. 3156018

SlingBar Cover Paddy 30 (fits Universal SlingBars 350, 450, and 600)

Prod. No. 3607001

Holder for Quick Reference Guide

Prod. No. 2000100

Quick Reference Guide

Prod. No. 2040400

Viking M / L / XL

5 Electrical Emergency Lowering / Raising

1 HandControl IR UP

A

Quick Reference Guide

UP

XS DOWN

DOWN

Widening the base Narrowing the base

5

4

3

MS

Note! If the lift has not been used for more than 24 hours, before the HandControl IR can be used, the system must be activated by pressing any button on the operation panel.

M

Ergonomics XX L XL •L Never lift manually – let the lift do the lifting. • Take it easy. Work calmly and methodically. • Don’t strain your back! Work in a walking stance with your back straight. • Use the bed’s raising and lowering functions. • Reduce the lever effect. Work close to the patient and the lift.

6 Locking the Wheels Unlock Lock

A Green - hand control active Yellow - change batteries

7 2

S

Up (lower lifting speed) Down (lower lifting speed)

English

1

Cleaning When necessary, clean the lift with a moist cloth, using warm water or disinfectant.

Viking M

Viking L, Viking XL

Simple Troubleshooting

7 Latches

Check to ensure that:

Read the instruction guide for more information.

• the emergency stop is not pressed in, see 3 • the battery of the lift is charged

6

2 Operation Panel 1

2

3

4

• the lift has been in use the last 24 hours, see 1 • the hand control does not indicate battery replacement, see 1 A.

Indicator lamps 1. Hand control active

(Viking M)

2. Overload 3. Service indication 4. Expected Life Time (ELT)

Viking M, Viking L

Viking XL

Other Quick Reference Guides

Charging the Batteries

Quick reference guides for Liko’s lifts and slings are available for downloading at www.liko.com.

Read the instruction guide for more information.

Safety Instructions • Read the instruction guides for the lift and lifting accessories before use. • Plan the lifting operation carefully. • Check to ensure that the sling’s strap loops are correctly fastened to the sling bar hooks when the sling strap is extended, but before the patient is lifted from the underlying surface.

Activate:

Reset: • Charge the lift regularly after use. • The lift does not function during charging. • The lift cannot be charged with the emergency stop engaged.

• Personnel using the lift are informed of the correct operation and use of the lift. • Maximum load: Viking M 205 kg (450 Ibs.) Viking L 250 kg (550 Ibs.) Viking XL 300 kg (660 Ibs.)

© Copyright Liko AB

3 Emergency Stop

Position of the Lift when Lifting From/To:

Bed

Chair/Hygiene chair

Floor

4 Mechanical Emergency Lowering

To retain max. load it is essential to use accessories rated for the same max. load or greater.

7EN137107 Rev. 4 • 2020

15

IMPORTANT! This quick reference guide does not replace the lift’s instruction guide, which can be downloaded at www.liko.com.

7EN137503-01

Universal SlingBar 350* Max. 300 kg (660 lbs)

www.liko.com Manufacturer:

Unbalanced lifting poses a tipping risk! Viking M

Viking L, Viking XL

Read the instruction guide for more information.

Liko AB SE-975 92 Luleå Sweden [email protected]

www.hillrom.com

Quick-Release Hook Liko™ Quick-Release Hooks is a system for quick change of lifting accessories on Liko’s mobile and stationary lifts. Viking™ M mobile lift must be equipped with the Q-link 13 in order to be used with the Quick-release Hook. The Quick-release Hook Universal fits the Universal SlingBar 350, 450 and 600 (prod. no. 3156074 - 3156076). Quick-release Hook TDM fits the SlingBar Mini 220 (prod. no. 3156005), Sling Cross-bar 450 and 670 (prod. no. 3156021 and 3156018) and Universal TwinBar 670 (prod. no. 3156077). When changing to a sling bar with quick release hook, the lifting height is reduced by 33 mm (1.3 in) in comparison with a fixed sling bar. Contact Hill-Rom for further information.

Quick-release Hook Universal Prod. No. 3156508

Quick-release Hook TDM Prod. No. 3156502

Y Z

X

Q-link 13 Prod. No. 3156509

Viking™ M mobile lift can be used in combination with the Liko™ OctoStretch for horizontal lifting. Liko™ OctoStretch with Leveller Prod. No. 3156056 Prod. No. 3156056

Bag for SlingBars Prod. No. 2001025

LikoScale™ device for weighing a patient in combination with Viking™ mobile lifts. Adapter 12 mm is required. LikoScale™ 350, Max 400 kg (880 lbs) Prod. No. 3156228 LikoScale™ 350 is certified according to the European Directive NAWI 2014/31/EU (Non-Automatic Weighing Instruments). LikoScale™ devices only for use in the United states and Canada: LikoScale™ 200, Max. 200 kg (440 Ibs.) Prod. No. 3156225 LikoScale™ 400, Max. 400 kg (880 Ibs.) Prod. No. 3156226. Contact your Hill-Rom representative for more information.

Viking Armrest M

Prod. No. 2047011

Leg Protector Viking S, M

Prod. No. 2046011

Battery charger, for wallmounting or to use with the Table charger housing Prod. No. 2004106

7EN137107 Rev. 4 • 2020

Table charger housing excl. charger and battery Prod. No. 2107103

16

LikoScale 350

Adapter 12 mm

Prod. No. 3156228

Prod. No. 2016504

Battery Lead battery (Pb) Prod. No. 2006106

Battery Li-ION battery Prod. No. 2006109

www.hillrom.com

Troubleshooting The lift do not work up/down with Hand Control. The base-width adjustment doesn’t work (in/out) with the Hand Control.

1. Make sure that the emergency stop button has not been activated (shall not be pressed in). 2. Check the battery capacity. Check if the Li-ION battery has been set in to sleep mode, see chapter "Operation". 3. Make sure that the battery is properly seated in the control box. 4. Check that the charger cable is not connected to an electric outlet. 5. Check that the handcontrol cable is correctly connected to the control box. 6. Check that the lift arm actuator cable is correctly connected to the control box. 7. Check that the base widht actuator cable is correctly connected to the control box. 8. If the problem persists, please contact Hill-Rom.

The charger doesn’t work.

1. Check that the charger cables are connected correctly. 2. Make sure that the battery is properly seated in the control box. 3. Try an alternative mains outlet. 4. If the problem persists, please contact Hill-Rom.

The lift is stuck in the high position.

1. Make sure that the emergency stop button has not been activated (shall not be pressed in). 2. Make sure that the battery is properly seated in the control box. 3. Check the battery capacity. Check if the Li-ION battery has been set in to sleep mode, see chapter "Operation". 4. Check that the handcontrol cable is connected correctly. 5. Electrical emergency lowering, use the operation panel to lower the patient onto a firm surface, see chapter; Operation. 6. Use the mechanical emergency lowering device to lower the patient onto a firm surface, see chapter; Operation. 7. If the problem persists, please contact Hill-Rom.

If you hear unusual sound from the lift.

Contact Hill-Rom.

Recycling Instructions Lead battery (Pb) or Li-ION battery Waste of Electrical and Electronic Equipment (WEEE). Metals

Old batteries are to be deposited at the nearest recycling station or given to personnel authorized by Hill-Rom. Hill-Rom evaluates and provides guidance to its users on the safe handling and disposal of its devices to aid in the prevention of injury, including, but not limited to: cuts, punctures of the skin, abrasions, and any required cleaning and disinfection of the medical device after use and prior to its disposal. Customers should adhere to all federal, state, regional, and/or local laws and regulations as it pertains to the safe disposal of medical devices and accessories. If in doubt, the user of the device shall first contact Hill-Rom Technical Support for guidance on safe disposal protocols. 7EN137107 Rev. 4 • 2020

17

www.hillrom.com

Cleaning and Disinfection

Safety recommendations Cleaning and disinfecting procedures for Liko Mobile lifts. This instructions do not replace the facility’s own cleaning and disinfection policies. • Wear protective equipment according to manufacturer’s instruction and per facility protocol throughout the cleaning operations, such as: rubber gloves, goggles, apron, face mask and shoe covers. • Unplug mains (AC power source) before cleaning and disinfection. • Never clean the lift by pouring water on it, steam cleaning it, or by using a high-pressure jet. • Refer to the recommendations made by the cleaning and disinfecting product manufacturer. Equipment: • Protective equipment (such as: rubber gloves, goggles, apron, face mask and shoe covers) as recommended by the facility protocol and manufacturers instructions • Clean buckets • Cloths for washing and drying • Soft brush • Warm water • To find Cleaning / Disinfectants compatible or not compatible for use on Liko’s products, follow the ”Application of commonly used Cleaning / Disinfectants on Liko products” in this document. Cleaning instructions 1.

Unplug mains (AC power source) before cleaning and disinfection.

2. Clean the lift with a cloth moistened with warm water and a neutral cleaning agent approved by your organization. A soft brush may be used to remove stains and resistant dirt. 3. Wipe off the entire lift with a cloth moistened with clean water starting from the top and working down. The cloth shall not be so damp that it drips. To have access to all areas run the lift into the highest and lowest positions and extend the base width adjustment entirely in and out. Remove the Battery to have access behind the battery. NOTE! Do not clean the piston rod! 4. Pay special attention to the following areas: • Sling bar • Mechanical emergency lowering • Handles • Control box • Battery • Hand control • Emergency stop • Operation panel/display • Locking handles • Wheels

Do not clean! (piston rod)

Disinfection Instructions 1. For the use of suitable disinfectants see ”Application of commonly used Cleaning / Disinfectants on Liko products” in this document. 2. Use the choice of disinfectant according to the manufacturer’s instructions and repeat the work step as in ”Cleaning instructions" 3. Remove traces of disinfectant after disinfection. Wipe off the lift with a cloth moistened with clean water starting from the top and working down. The cloth shall not be so damp that it drips. The lift may not be cleaned with CSI or equivalent. The hand control may not be cleaned with Viraguard or equivalent. The control box may not be cleaned with Anioxy Spray or equivalent. 7EN137107 Rev. 4 • 2020

18

www.hillrom.com

7EN137107 Rev. 4 • 2020

19

www.hillrom.com

*) Or equivalent

Adipic acid 10-30% Amorphous silica < 1% Sodium Toluene sulphonate 5-10 % Troclosene sodium 10-30 %

Hydrogen peroxyde (2.5-10 %) Lauryldimethylamine oxid (0-2.5 %) Ethanol (2.5-10 %)

Ethanol

Troclosene sodium

Magnesium monoperoxyphtalate hexahydrate (50-100%) Anionic surfactant (5-10%) Nonionic surfactant (1-5%)

Isopropyl alcohol = 70%

Alcohol

Organic peroxide (type E, solid)

Sodium hypochlorite

Bleach

Benzyl-C12-18-alkyldimethylammonium, chlorides (22 %) 2-Phenoxyethanol (20 %) Tridecylpolyethylenglycolether (15 %) Propan-2-ol (8 %)

Ortho-Phenylphenol = 3.40% Ortho-Benzyl-para-Chlorophenol = 3.03

Phenolic

Benzyl-C12-18-alkyldimethylammonium, chlorides

Hydrogen Peroxide 0.1 -1.5% BenzylAlcohol: 1-5% Hydrogen Peroxide 0.1 -1.5% BenzylAlcohol: 1-5%

Accelerated Hydrogen Peroxide

n-Alkyl dimethyl benzyl ammonium chlorides = 0.105% n-Alkyl dimethyl ethylbenzyl ammonium chlorides = 0.105%

Alkyl dimethyl benzyl ammonium chloride = 13.238% Alkyl dimethyl ethylbenzyl ammonium chloride = 13.238%

Quaternary ammonium chloride

Quaternary ammonium

Didecyl dimethyl ammonium chloride = 8.704% Alkyl dimethyl benzyl ammonium chloride = 8.19%

Active ingredient

Quaternary ammonium chloride

Chemical class

Application of commonly used Cleaning / Disinfectants on Liko products

4-6 in use

7

5.3 in use

approx 8.6 in use

11.5 - 12.5

5.0 – 7.0

12.2

3.1 +/- 0.4 in use

3

9.5 in use

9.0 – 10.0 in use

pH

Chlor-Clean

Anioxy-Spray WS

Dismozon Pur

Terralin Protect

CSI

Viraguard

Dispatch

Wexcide

Oxivir Tb

HB Quat 25L

Virex II (256)

Cleaners / Disinfectant *)

Guest Medical Ltd

Anios

Bode

Shülke

Central Solutions Inc.

Veridien

Caltech

Wexford Labs

Johnson/Diversey

3M

Johnson/Diversey

Manufacturer *)

The lift straps for Golvo™ and ceiling lifts

Control box for all mobile lifts

The lift straps for Golvo™ and ceiling lifts

Foot rest for Sabina™ and Roll-On™

Viking™, Liko M220™, Liko M230™, Uno™, Sabina™, Golvo™, LikoLight™, Roll-On™, Likorall™, Multirall™

Hand controls for all lifts

The lift straps for Golvo™ and ceiling lifts

The lift straps for Golvo™ and ceiling lifts

Foot rest for Sabina™ and Roll-On™

May not be used on the following items:

Inspection and Maintenance For trouble-free use, certain details should be checked each day the lift is used: • Inspect the lift and check to make sure that there is no external damage. • Check the sling bar attachment. • Check the functionality of the latches. • Check the integrity of the lifting motion and the base-width adjustment. • Check to make sure that the emergency lowering (both electrical and mechanical) works. • Charge the batteries each day the lift is used and then check that the charger works. When necessary, clean the lift with a moist cloth and check that the wheels are free from dirt. Find more detailed information regarding cleaning and disinfection of your Liko product in chapter; Cleaning and Disinfection. The lift should not be exposed to running water. Service A periodic inspection of the lift should be carried out at least once per year. Periodic inspection, repair and maintenance should be performed only in accordance with the Liko™ Service Manual, and by personnel authorized by Hill-Rom and using original Liko™ spare parts. Service activities are not allowed with the patient in the lift.

Expected Life Time The product has an expected service life of 10 years when correctly handled, serviced and periodically inspected in accordance with Liko’s instructions. Parts listed below are subject to wear and tear and have specific expected life time: - Handcontrol, expected life time 2 years, - Battery, expected life time 3 years. Transport and Storage During transport, or if the lift is not to be used for a long time, the Emergency Stop should be activated. The environment where the lift is transported and stored should have a temperature of -10°C to +50°C (14°F to 122°F), 20-90% humid., pressure 700-1060 hPa. The environment where batteries are transported and stored is recommended to have a temperature of -10°C to +40°C (14°F to 104°F) , 20-80% humid., pressure 700-1060 hPa. Notice to Users and/or Patients in EU Any serious incident that has occurred in relation to the device, should be reported to the manufacturer and the competent authority of the Member State in which the user and/or patient is established. Product Changes Liko products undergo continuous development, which is why we reserve the right to make product changes without prior notice. Contact your Hill-Rom representative for advice and information about product upgrades. Design and Quality by Liko in Sweden The management system for both manufacturing and development of the product is certified in accordance with ISO9001 and its equivalent for the medical device industry, ISO13485. The management system is also certified in accordance with the environmental standard ISO14001.

www.hillrom.com Liko AB Nedre vägen 100 975 92 Luleå, Sweden +46 (0)920 474700 Liko AB is a subsidiary of Hill-Rom Holdings, Inc.

© Copyright R&D Liko AB 2020. ALL RIGHTS RESERVED

Service Agreement Hill-Rom offers the opportunity to enter into service contracts for the maintenance and regular inspection of your Liko product.