Luxtec MLX 300W Xenon Light Source Operation and Service Manual Rev A 2019

Table of Contents Indications for Use ... 3 Symbols ...4 General Warnings... 5 Precautions ... 5 Overview ...6 Operation ...6 Xenon Lamp Module Replacement ...8 Fuse Replacement...9 Optional Floor Stand Assembly... 10 Replacement Parts and Accessories... 11 Maintenance and Cleaning ... 11 Troubleshooting ... 12 Specifications ...13 Electromagnetic Compatibility (EMC) User Information ... 14 Block Diagram...17 Repair and Return... 18 Limited Warranty ... 18

2

Integra Luxtec ®

®

MLX 300 Watt Xenon Light Source

CAUTION: FEDERAL (USA) LAW RESTRICTS THIS DEVICE TO SALE BY OR ON THE ORDER OF A PHYSICIAN

Indications for use The Integra® Luxtec® MLX Light Source is designed to supply high intensity white light through a fiber optic cable for illumination of a surgical field during a surgical and/or medical procedure. The Integra Luxtec MLX Light Source should never be used in ocular surgery or in a surgical procedure requiring direct illumination of the eye. This device is intended to be used by professional healthcare users.

3

Symbols Found on a medical grade light source, other illumination related equipment, fiber optic cables and corresponding packaging.

Caution

Consult Instructions for Use

Caution: High Voltage

Fuse

High Temperature Refer to Instruction Manual

Alternating Current Type CF Equipment

Type BF Equipment Equipotentiality

Protective Earth

Humidity Limitation

Do Not Dispose

On / Off

Stand-by Temperature Limitation System Status Display Atmospheric Pressure Limitation System Keep dry Push REF

Part Number Hours

LOT

Batch Code Serial Number

EC REP

Authorized Representative in the European Community

Manufacturer

Date of Manufacture 0123 This device meets CE requirements

Certified by CSA

Intensity Motor

Fan

Over Temperature

Lamp

Brightness

4

Integra Luxtec ®

®

MLX 300 Watt Xenon Light Source

General Warnings The user should carefully study the Operation and Service Manual before using the equipment in a clinical environment. This Manual contains information about the proper procedures for preparing this product for its use and care. Instructions should be followed, with special attention given to warnings, controls and user specifications. The Manual should be available to the appropriate personnel. • SAFETY PRECAUTIONS MUST ALWAYS BE EXERCISED WHEN USING ELECTRICAL EQUIPMENT TO PREVENT OPERATOR/ PATIENT SHOCK, FIRE HAZARD OR EQUIPMENT DAMAGE. • FIRE HAZARD: DO NOT DRAPE OR COVER THE LIGHT SOURCE WHILE IT IS OPERATING. • Before every procedure, carefully inspect the light source to ensure it has been properly maintained and cleaned, and that it is fully functional. DO NOT use if inspection reveals any damage such as case damage or loose connectors. • Follow the instructions of other manufacturer’s equipment when used in conjunction with this product. • To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. • To reduce the risk of fire and electric shock, do not expose electrical equipment to moisture. When cleaning, do not immerse any electrical device in liquid. • Do not use or store liquids on or above the light source. • Electric shock hazard. If unit is not functioning properly, DO NOT OPEN. Please refer to the Repair and Return Section of this Manual. • All electrical equipment must be used with approved hospital grade power cords and power plugs inserted properly into grounded AC power outlets. If replacement is necessary, replace only with approved power cord. • The light source should never be used in ocular surgery or in a surgical procedure requiring direct illumination of the eye. • Use care not to point any fiber optic cable directly at the eye while operating the light source. • The light source produces high intensity light. Thermal burns can result from improper use of the light source or from the light output of the fiber optic cable. • Explosion Hazard. Do not use in an oxygen rich environment or in the presence of flammable anesthetics, liquids, vapors, gases or dusts.

5

• Keep cooling vent and fans free of obstructions. • When light source is not in use, turn off the power or put the unit in stand-by mode. • Ensure that the fiber optic cable matches the port type to prevent damaging the optical components of the light source. For user convenience, the light source has a turret with labeled selectable ports. • Do not use the headlight at distances of less than 10” (25cm). • Warning: No modification of this equipment is allowed. • Do not position the equipment so that it is difficult to remove the power plug. Precautions • Take precautions to verify that the fiber optic cable is appropriately suited for the light source. Xenon and other high illumination light sources require premium fiber optic cables in order to achieve optimal performance and prevent damage to the fibers, thereby diminishing the quality of the light output or the useful life of fiber optic cable. Use only fiber optic light guide cables with the correct proximal fitting for your turret and approved and tested for compatibility with high intensity Xenon lamps of 300W or higher. • Take precautions not to touch or disconnect the cable end fitting from the turret until the Light Source has been “shut down” for a period of time and allowed to cool. The cable end fitting will remain hot immediately following shut down, which can cause burns. • Take precautions to not place and rest a hot cable end fitting and/or head light on a patient or allow the system to come in contact with un-protected hands or tissue. The entire system should be allowed to cool following use. Failure to do so can cause burns and/or tissue damage.

Overview The MLX light source delivers 300 watts of cool white infrared (IR) filtered light. The lamp is housed in a lamp module that can be easily serviced without special tools. Set Up And Inspection Before Use The light source comes with the hospital grade power cord packaged separately. Verify that both components are in good condition. This device should be used in environments that meet the operating environmental conditions in the specification section of this manual. Before turning power on to the light source, make sure the unit is plugged into any standard 100VAC to 240VAC 50-60Hz (as appropriate) outlet. Grounding reliability is guaranteed only when connected to a “hospital grade” receptacle. Allow a minimum of 2 inches (5.08 cm) clearance at the rear and sides of the unit for cooling air flow. Ensure that the unit is not near air exhaust or against other equipment.

Warning The MLX light source monitors air intake temperature and will turn off if ambient temperature is > 40o C

Operation 1. Insert a fiber optic cable in the proper port in the turret. The active port is indicated by a left facing arrow on the perimeter of the turret (See Figure 1). Available ports are ACMI, Olympus, Storz and Wolf cable-compatible. All ports are identified appropriately. 2. Press the Power Switch in the upper left corner of the front panel (See Figure 2). 3. When the Power Switch is pressed the Stand-by Light (Figure 3) will blink and there will be a 3 – 4 second delay before the Xenon Lamp illuminates while the system does a self-diagnostic check. 4. Press the Stand-by Button.

1

2

3

6

Integra Luxtec ®

®

MLX 300 Watt Xenon Light Source

5. The system will start up at the same light intensity as when last used. For new systems, the light intensity will start at the minimum 20% setting. 6. To adjust the light intensity, push the Membrane Switches (Figure 4): + to increase or - to decrease the light output or intensity. Range is 0%, 20 – 100% in 5% increments. Holding the + or – button will change the intensity more quickly.

Note It is strongly recommended that the light be used at the minimum intensity for good visualization.

7. The System Status Display can be pressed to show both lamp time and system operation time. A second press of the switch will show the software version of the system monitor. A third press returns to light output. (The system will automatically return to the light intensity reading after 15 seconds). 8. The system may be placed in and out of stand-by mode by using the stand-by switch. The system will emit no light in this state and allow the surgeon to unplug a headlight, move around the table, or change cables in a laparoscopic or endoscopic procedure.

Caution Fiber Optic Cable end fitting can be hot

4

Note If unit is left in stand-by mode for 15 minutes, it will automatically shut off the lamp. Fans will keep running. To re-activate, push the Stand-by Button. 9. Take precautions not to touch or disconnect the cable end fitting from the turret until the light source has been “shut down” for a period of time and allowed to cool. The fiber optic cable end fitting will remain hot immediately following shut down, which can cause burns. 10. To shut the system off, simply press the main Power Switch as in Step 2.

7

membrane switches system status display

Xenon Lamp Module Replacement Note Please adhere to appropriate safety precautions when performing lamp replacement. Only qualified personnel should service this device. Protective facemask and/or proper safety glasses should be worn when replacing the lamp module. Before changing the lamp module, turn power off and allow the light source to cool for at least fifteen (15) minutes.

Please read and comply with all Precautions and General Warnings listed in this manual. To remove lamp: 1. Make sure the power is off and the hospital grade power cord is disconnected. 2. Remove the retaining screws from the top plate (Figure 5) and retain screws. 3. Slide the top plate towards the back of the unit until it stops. 4. Lift the top cover up and off the unit. 5. Unscrew the lamp module door and remove (Figure 6) and retain screw. 6. Grasp the module by the tabs and pull directly up (Figure 7). To replace lamp: 1. Orient the lamp module (P/N 001320LX) to face forward. 2. Place the module into the light source. 3. Seat module securely. 4. Replace the lamp module door and secure it with the screw. 5. Align top cover brackets into slots and slide forward. 6. Slide the top plate forward until it engages the front panel. 7. Replace the retaining screws in the rear panel. 8. Replace the hospital grade power cord and turn on power to verify operation. To reset lamp age meter: 1. Using the membrane switch, turn the display to the lamp age/system age screen. 2. On the rear of the unit insert a pen/pencil or other suitable pointed object into the slot marked RESET (Figure 8). 3. Push until a click is felt. 4. Verify that the lamp age has been reset to 0.

5

6

7

Note The System Age reading CANNOT be reset. 8

RESET

8

Integra Luxtec ®

®

MLX 300 Watt Xenon Light Source

Fuse Replacement The fuses for the light source are located in the power entry module in the rear of the unit and may require replacement if the system does not respond to the power switch. To replace a fuse: 1. Remove the hospital grade power cord from the back of the light source. 2. Using a small flat screwdriver, pry open the retaining door (Figure 9) and pry out the red plastic block from the power entry module (Figure 10). 3. Check to see if either fuse is blown; if blown, replace with a fuse of the same rating (Integra P/N 600987). 4. Replace the red block in the housing. 5. Snap the retaining door into place. 6. Plug cord back into light source and retest the unit.

9

9

10

Optional Floor Stand Assembly The floor stand assembly includes the following components along with the necessary Phillips head screwdriver: 1. Base with five (5) casters (2 locking) 2. One column with light source base plate 3. Handle Figure 10 4. MLX light source base Floor stand assembly instructions: 1. With the handle positioned so that the Luxtec logo is properly aligned, slide the handle onto the column and center the handle about 5 inches (13cm) below the light source base plate. Tighten handle screw to hold in place. 2. Insert assembled column into the base. Seat firmly. 3. Attach the light source base onto the base plate (Figure 11) with the four (4) screws provided, using the Phillips head screwdriver provided. 4. Secure the light source to base plate by aligning the feet to the holes on the surface of the plate. Tighten the two screws on the bottom of the plate to the light source (Figure 12).

11 10 Figure 12 11 Figure

Figure 11

10

Integra Luxtec ®

®

MLX 300 Watt Xenon Light Source

Replacement Parts And Accessories To place an order, contact your local Integra distributor or call Integra Customer Service at 1-800-431-1123 (USA & Canada only) or +1-914-789-7094 to identify your local Integra representative. Light Source Reference

Description

00MLX

300 Watt Xenon Light Source with Turret (ACMI, Wolf, Storz and Olympus)

Accessories Reference

Description

001320LX 600987

Xenon Lamp Module Fuse 6.3 Amp, Slow Blow

Optional Accessories Reference

Description

AX2100BIF 001337 601949EUR6 601949UK6 601949US6P1

UltraLite® Pro headlight with 9ft (275cm) premium bifurcated cable, Mark II module and gown clips. MLX Floorstand European Power Cord 20’ (6m) Hospital Grade UK Power Cord 20’ (6m) Hospital Grade USA Power Cord 20’ (6m)

Maintenance and Cleaning • Allow unit to cool for at least 15 minutes prior to cleaning. • Unplug the power cord before cleaning. The light source exterior can be cleaned and disinfected using 70% isopropyl alcohol. Allow 5 minutes for alcohol to evaporate before reconnecting to power. • Use a vacuum cleaner and a soft brush to remove visible dust accumulation from fan and vent holes whenever necessary and always when replacing the lamp.

11

Troubleshooting Trouble Area

Possible Cause

Corrective Action

No power

Light source not plugged in

Plug in light source

Top cover not closed

Close and secure top cover

System overheated

Contact Integra for service NOTE: System may cycle on/off if left plugged in and powered

Light source not turned on

Turn power on

Bad/no lamp

Check lamp seating/replace lamp module

Attenuator closed

Verify not in standby mode

Turret mispositioned

Rotate turret to desired adapter fitting

Blown fuse

Replace fuse as indicated in maintenance section

Cooling system obstructed

Clear obstructions, cycle power

System overheated

Contact Integra for service NOTE: System may cycle on/off if left plugged in and powered

System shuts down during use

Cooling system obstructed

Clear obstructions, cycle power

System overheated

Contact Integra for service NOTE: System may cycle on/off if left plugged in and powered

Lamp shroud shows signs of melting

Cooling system obstructed

Clear obstructions, cycle power

System overheated

Contact Integra for service NOTE: System may cycle on/off if left plugged in and powered

Reduced Light Output

Cable mismatched to turret

Rotate turret to matching adapter fitting

Attenuator mispositioned

Verify not in standby mode

Bad lamp

Replace lamp module

No light output

Fault Symbol

Possible Cause

Corrective Action

Lamp change (will blink after 1000 hours)

Change lamp. Module Part number 001320LX

Fan failure

Shut off system to reset. If it does not reset contact Integra for service

Lamp overheat

Shut off system to reset. If it does not reset contact Integra for service

Attenuator motor failure

Shut off system to reset. If it does not reset contact Integra for service

12

Integra Luxtec ®

®

MLX 300 Watt Xenon Light Source

Specifications Lamp Type

Xenon Short Arc Lamp

Wattage

300 Watts

Lamp Life

1000 Hours

Light Source

13

Dimensions

15.4”L x 11.2”W x 5.9”H (390mm L x 285mm W x 150mm H)

Weight

12.5 lbs. (5.7 kg)

Power Input

100~240VAC, 50/60Hz, 6.3A

Fuses (2)

6.3A, 250VAC, 5x20 mm, Slo-Blo, IEC Standard

Protection Class

Class 1

AC Power Leakage

Leakage current to chassis (with ground wire intact), less than 100 microamps Leakage current to chassis (with ground wire interrupted), less than 500 microamps

Applied Part Classification

Type CF

Electrical Safety

Conforms to UL 60601-1, IEC 60601-1, and CSA C22.2 NO. 601.1

Electromagnetic Compatibility

IEC60601-1-2

Environment: Storage Temperature Operating Temperature Storage Humidity Operating Humidity

0 to 50°C (32 to 122°F) 10 to 40°C (41 to 104°F) 10 to 85% non-condensing 10 to 85% non-condensing

Atmosphere Pressure: Storage Operating

500 to 1060hPa 700 to 1060hPa

Power Cord

Hospital grade

Mode of Operation

Continuous

Ingress Protection

IP20

Power Dissipation

450 Watts

Electromagnetic Compatibility (EMC) User Information Warning Medical Electrical Equipment needs special precautions regarding EMC and needs to be installed and put into service according to the Electromagnetic Compatibility [EMC] information provided in the accompanying documents.

Warning Portable and Mobile RF Communications Equipment can affect Medical Electrical Equipment.

Warning The equipment or system should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is necessary, the equipment or system should be observed to verify normal operation in the configuration in which it will be used.

Note The EMC tables and other guidelines that are included in the Instruction Manual provide information to the customer or user that is essential in determining the suitability of the Equipment or System for the Electromagnetic Environment of use, and in managing the Electromagnetic Environment of use to permit the Equipment or System to perform its intended use without disturbing other Equipment and Systems or non-medical electrical equipment.

Table 201: Guidance and Manufacturer’s Declaration – Emissions All Equipment and Systems The MLX light source is intended for use in the electromagnetic environment specified below. The customer or user of the MLX light source should assure that it is used in such an environment. Emissions Test

Compliance

Electromagnetic Enforcement – guidance

RF Emissions CISPR 11

Group 1

The MLX unit uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.

RF Emissions CISPR 11

Class B Radiated and Conducted Emissions

The MLX unit is suitable for use in all establishments including domestic, and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes. Conducted Emissions Tests Performed at both 240VAC, 50Hz and 120VAC, 60Hz

Harmonics IEC 61000-3-2

N/A

Equipment intended for Professional Use Only

Flicker IEC 61000-3-3

N/A

Equipment intended for Professional Use Only

14

Integra Luxtec ®

®

MLX 300 Watt Xenon Light Source

Electromagnetic Compatibility (EMC) User Information Table 202: Guidance and Manufacturer’s Declaration-Immunity All Equipment and Systems The MLX light source is intended for use in the electromagnetic environment specified below. The customer or user of the MLX light source should assure that it is used in such an environment. Compliance Level

Electromagnetic Environment - Guidance

Electrostatic Discharge (ESD) ±6kV contact IEC 61000-4-2 ±8kV air

±6kV contact

Floors should be wood, concrete or ceramic tile. If floors are synthetic, the relative humidity should be at least 30%.

Electrical Fast Transient/ burst IEC 61000-4-4

±2kV on AC Mains

±2kV on AC Mains

Surge IEC 61000-4-5

±1kV Differential ±2kV Common

Immunity Test

IEC 60601 Test Level

±8kV air

Mains power quality should be that of a typical commercial or hospital environment. Note - Tests Performed at both 240VAC, 50Hz and 120VAC, 60Hz

±1kV Differential ±2kV Common

Mains power quality should be that of a typical commercial or hospital environment. Note - Tests Performed at both 240VAC, 50Hz and 120VAC, 60Hz

Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11

Power Frequency 50/60Hz Magnetic Field IEC 61000-4-8

>95% Dip for 0.5 Cycle

>95% Dip for 0.5 Cycle

60% Dip for 5 Cycles

60% Dip for 5 Cycles

30% Dip for 25 Cycles

30% Dip for 25 Cycles

>95% Dip for 5 Seconds

>95% Dip for 5 Seconds

3A/m

3A/m

Mains power quality should be that of a typical commercial or hospital environment. If the user of the MLX unit requires continued operation during power mains interruptions, it is recommended that the MLX unit be powered from an uninterruptible power supply or battery. Note - Tests Performed at both 240VAC, 50Hz and 120VAC, 60Hz Power frequency magnetic fields should be that of a typical location in a typical commercial or hospital environment. Note - Tests Performed at both 50Hz and 60Hz

15

Electromagnetic Compatibility (EMC) User Information Table 204: Guidance and Manufacturer’s Declaration – Emissions Equipment and Systems that are NOT Life-Supporting The MLX light source is intended for use in the electromagnetic environment specified below. The customer or user of the MLX light source should assure that it is used in such an environment.

Immunity Test

IEC 60601 Test Level

Compliance Level

Electromagnetic Environment - Guidance

Conducted RF IEC 61000-4-6

3 Vrms from 150 kHz to 80 MHz

V1 = 3 Vrms

Portable and mobile RF communications equipment should be separated from the MLX light source by no less than the recommended separation distances calculated/listed below:

D = (3.5 / V 1) P Radiated RF IEC 61000-4-3

3 V/m 80 MHz to 2.5 GHz

E1 = 3V/m

D = (3.5 / E1) P 80 to 800 MHz D = (7 / E1) P

800 MHz to 2.5 GHz

Where P is the maximum power rating in watts and D is the recommended separation distance in meters. Field strengths from fixed transmitters, as determined by an electromagnetic site survey, should be less than the compliance levels (V1 and E1). Interference may occur in the vicinity of equipment containing a transmitter

Table 206: Recommended Separation Distances Between Portable and Mobile RF Communications Equipment and the MLX Equipment and Systems that are NOT Life-Supporting The MLX light source is intended for use in the electromagnetic environment in which radiated disturbances are controlled. The customer or user of the MLX light source can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF Communications Equipment and the MLX light source as recommended below, according to the maximum output power of the communications equipment.

Recommended Separation Distances for the MLX (meters) 150 kHz to 80 MHz

80 to 800 MHz

d = 1.1667 P

d = 1.1667 P

0.01

0.11667

0.11667

0.23333

0.1

0.36894

0.36894

0.73785

1

1.1667

1.1667

2.3333

10

3.6894

3.6894

7.3785

100

11.667

11.667

23.333

Maximum Output Power (Watts)

800 MHz to 2.5 GHz

d = 2.3333 P

16

LINE

LAMP HOURS RESET SWITCH

4

P1

P/S FAN

POWER ENTRY MODULE

THERM 1

t

THERM 2

t

LOAD

A

D

BRN

GRN/YEL

BLUE

THERM 3

t

FERRITE CORE

BRN

BLUE

STANDBY SWITCH

LINE

J20

J9

FILTER

J1

J30

TP4

+

LOAD

CONTROL SWITCHES

NA

FINISH

NA

MATERIAL

B5

B4

08/30/11

08/30/11

DATE 03/20/08

L

N

POWER SUPPLY

THIRD ANGLE PROJECTION

J1

LIMIT SWITCH

ATENUATOR MOTOR

FERRITE CORE

NC

C

GREG HARPER

APPROVED

M.PUMA

CHECKED

BJF

GRN/YEL

DRAWN

BRN

BLU

BRN

WHT/BRN

UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES ANGLES FRACTIONS DECIMALS .X±.020 ±1/2 ±1/32 .XX±.010 .XXX±.005 32 MACHINED SURFACES: BREAK SHARP EDGES .005

J10

DISPLAY

CONTROL BOARD

M

A1

C INTERLOCK SAFETY SWITCH

PARTS LIST

PART NO.

NO

BRN

A2

C 581519

SIZE

TITLE

BRN

LAMP -

LAMP +

GRN/YEL

POWER SWITCH

G

N C

LENS SIDE

581519

DRAWING NO.

C

REV

22 TERRY AVENUE BURLINGTON, MA 01803 TEL: (781)-272-1233

THERMAL SWITCH N-C

XENON LAMP

FAN SIDE

MLX SCHEMATIC

WHITE

WHITE

SEE AGILE

CC 09/06/13

SEE AGILE

GREG HARPER 08/30/11

TKC 08/30/11

ECO# 110774: ADDED NEW SWITCH/ THERMAL SWITCH/TOL BLOCK,.X .020

DATE

ECO# 108904: REVISE FORMAT

APPROVED

C

INC BY

B

DESCRIPTION

1

ECN# 4980: ECN RELEASE

REVISIONS A

REV

2

Block Diagram

OCUMENT CONTAINS PROPRIETARY INFORMATION OF INTEGRA AND NOT BE REPRODUCED. THE INFORMATION CONTAINED HEREIN SHALL E DISCLOSED TO PERSONS EXCEPT THOSE NECESSARY TO PRODUCE RT OR PRODUCT OR USE THE PROCESS HEREIN SPECIFIED FOR A. NOR SHALL THE VENDOR BY THIS DOCUMENT BE LICENSED TO FACTURE SUCH PART OR PRODUCT OR USE SUCH PROCESS EXCEPT QUANTITIES ORDERED ON INTEGRA PURCHASE ORDERS. ANY TION TO THE FOREGOING CONDITIONS MUST BE APPROVED BY NCE WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED REPRESENTATIVE

P2

LAMP FAN

3

A

B

C

MLX 300 Watt Xenon Light Source

INTEGRA PROPRIETARY INFORMATION

17 BLU

®

BRN

Integra Luxtec ®

Repair And Return Information This device must be clean and decontaminated prior to return to Integra. Integra reserves the right to return unrepaired any equipment that is contaminated with blood or other organic material. Warranty Service and Repair: To obtain service under warranty or return product for repair, the customer should contact your local Integra representative or call Integra Customer Service at 1-800-431-1123 or +1-914-789-7094.

Limited Express Warranty Integra warrants that the new MLX light source shall be free from defects in material and workmanship under normal use and service for a period of three (3) years from the date of shipment. Integra’s sole and exclusive liability under the warranty shall be, at Integra’s option, either to repair any component which fails during the warranty period due to any defect in workmanship or material F.O.B. factory if: 1. Customer promptly reports such defect to Integra in writing, 2. If requested by Integra, customer returns equipment to Integra with shipping charges, and 3. Upon inspection, Integra finds the equipment to be defective. This warranty is contingent upon normal and proper use of the equipment. It does not cover equipment that has been modified with non-Integra parts without the written approval of Integra, subjected to unusual physical or electrical stress, or damaged during shipment. This warranty is non-transferable unless authorized in writing by Integra. Integra reserves the right to make design changes on its products without liability to incorporate said changes in Integra products previously designed or sold. Upon receipt of the product, it should be carefully inspected. If any defect is discovered, notification must be given immediately to the manufacturer or authorized distributor.

Disposal of the Product, Packing Material, and Accessories For disposal, observe the relevant regulations and laws valid in your country and utilizing regulations of the hospital and observing any local regulations. For further information, please contact Integra.

18

Integra Luxtec ®

®

Manufactured by: Integra LifeSciences (Ireland) Limited IDA Business and Technology Park Sragh, Tullamore, County Offaly, Ireland 0123

www.integralife.com

Integra, the Integra logo, Luxtec and UltraLite are registered trademarks of Integra LifeSciences Corporation or its subsidiaries in the United States and/or other countries. ACMI, Wolf, Storz, and Olympus are the trademarks or trade names of their respective owners. ©2019 Integra LifeSciences Corporation. All rights reserved. 60905988 Rev A 1430060-1