ULTRALITE PRO HEADLIGHT Operation and Service Manual Rev B March 2009

U l t r aL i te ® P r o H ea d l i g ht S y stem

Table of Contents

Page

Description

3 Indication For Use 4 -6 Assembly 6 Adjustments 7 Care and Maintenance 7 Replacement Part Numbers 8 Return Policy

2

U l t r aL i te ® P r o H ea d l i g ht S y stem

INDICATION FOR USE

This fiber optic headlight system is designed to deliver illumination from a high intensity light source for surgical site illumination. While the cable light source endfittings are compatible with all light sources, brightness and spot quality vary with specific types of light sources. The UltraLite® Pro systems perform best with Luxtec Xenon light sources.

MODULE FIBER OPTIC CABLE TOP PAD

GENERAL WARNINGS

The user of this product should be thoroughly familiar and trained in the use and care of this product. The user should carefully study this manual before making any attempt to use the product clinically. Instructions should be followed specifically, with special attention given to warnings and cleaning instructions. This manual should also be available to the surgical team during a procedure. Follow the instructions in the operating manuals of other manufacturer’s equipment when they are used in conjunction with this product.

CENTRAL ADJUSTMENT

ADJUSTMENT KNOB

Before every procedure, carefully inspect the light guide cable to ensure it has been properly maintained and cleaned and that it is fully functional. Use the light source at the lowest possible attenuation to prevent cable damage or excess heat. Light sources use high intensity lamps, which produce heat as well as brilliant light. The heat produced by the light source and the light output of the light guide cable can cause burns. Care should be taken to follow the maintenance and cleaning instructions. Excessive bending of the cable should be avoided. Use care not to point the head light directly at the eye while in operation. The brilliant light output can cause severe eye discomfort. FIRE HAZARD: DO NOT DRAPE OR COVER THE LIGHT SOURCE WHILE IT IS OPERATING. DO NOT PLACE THE fiber optic cable ON A DRAPE WHILE the lightsource IS OPERATING. CAUTION

The metal portions of the cable at the light source end gets hot during operation. Allow components to cool outside of the light source for at least 5 minutes before touching.

3

Information contained in this manual is subject to change without notice.

OCCIPITAL BASKET

U l t r aL i te ® P r o H ea d l i g ht S y stem

assembly

Assembly of the UltraLite® Pro Headlight System

(Fig 4b)

The UltraLite® Pro Headlight system consists of a headband, variable spot module, gown clips and a bifurcated fiber optic cable. To assemble the headlight, attach the variable spot module (Fig 1) Thread the bifurcated cable on the left and right of the central headband unit (Fig 5) in an over-under pattern as shown.

(Fig 1)

(Fig 5)

to the headband by sliding the tapered bottom end of the module into the headband (Fig 2) (Fig 2)

Continue threading the bifurcated cables on the left and right of the headlight adjustment bracket in an over-under pattern as shown (Fig 6). (Fig 6)

and push the top into the headband (Fig 3) until it makes an audible click. (Fig 3)

The cable can be slid forward or backward to allow more slack for comfort, as needed. To remove the cable from the module, grasp the strain relief in one hand and the module in the other hand and pull the strain relief straight up. • DO NOT disassemble by grasping the bifurcated cables as damage to the glass fibers may occur. To attach the fiber optic cable, insert the bifurcated metal fitting into the module (Fig 4a - b) until it clicks into place. (Fig 4a)

warning

The cable is made of glass fibers. When adjusting the cable on the headband, do not bend the cable more than 60 degrees. When properly assembled the cable should curve gently around the contours of the head and the headband.

Information contained in this manual is subject to change without notice.

4

U l t r aL i te ® P r o H ea d l i g ht S y stem

assembly

Assembly of the UltraLite® Pro Headlight System

(Fig 12)

Next open the headlight assembly fully by pulling the central unit (Fig 7) completely open and opening the (Fig 7)

circumferential adjustment (Fig 8) fully.

The headlight should then be adjusted circumferentially using the ratchet knob at the rear as shown (Fig 13). The UltraLite® Pro headlight is now ready for use. The headlight system comes with two gown clips to (Fig 13)

(Fig 8)

The pad (Fig 9) should be at the front of the headlight. (Fig 9)

relieve the weight of the fiberoptic cable from the head. One clip should be attached to the surgical gown or scrubs at, or just below shoulder level (Fig 14). Be sure to leave enough slack in the cable to allow for (Fig 14)

Place the headlight on your head. The occipital basket should be aligned (Fig 10) as shown. (Fig 10)

Grasp the headlight as shown (Fig 11) and push the headlight from front to back until it fits snugly. Adjust the pad front to back, (Fig 12) for a more comfortable fit

freedom of head movement. If the surgeon needs to detach the cable from the lightsource, the second gown clip is used to attach the cable to the gown or scrubs to eliminate the risk of dropping the cable. The spot size of the light may be adjusted from 20 – 100mm (0.8 – 4 in), based on a 46cm (18 in) working distance, by adjusting the iris (Fig 15). (Fig 15)

(Fig 11)

The module can be removed from the headband, if 5

Information contained in this manual is subject to change without notice.

U l t r aL i te ® P r o H ea d l i g ht S y stem

assembly / adjustments

needed, by placing a small flathead screwdriver in the slot above the module in the headband (Fig 16) and pushing the module out. Be sure to remove the fiber optic cable from the module first. (Fig 16)

Fiber optic cables are fine, high quality optical instruments.You can prolong the useful life by following a few guidelines: • Avoid stretching your cable, forming configurations involving sharp angles or kinks, or contact with sharp or pointed objects. The internal light fibers are made of glass, a material which breaks under stress. Fiber breakage will result in diminished light output. • Utilize the gown clips (provided) to keep the headlight cable secured to the surgeon’s gown for greater comfort and maneuverability.

Caution

To plug or unplug the fiber optic cable from the light source, it is recommended that the light source power be turned off. Be sure to hold the strain reliever near the end of the cable. This part of the cable is reinforced to prevent damage to the glass fibers inside, and to prevent burns.

• DO NOT use your fiber optic cable with any alterations to its original design or fabrication. • Keep the optical faces from contacting the floor or other hard surfaces. The resulting scratches will diminish light output.

ADJUSTMENTS

Once the headlight module and fiber optic cable are attached to the headband, the headlight assembly is ready to use. The headlight module can be adjusted vertically while wearing the headlight system by grasping the module and aligning the light spot to a comfortable working position. CAUTION

The metal portions of the cable at the light source get hot during operation. Allow components to cool outside of the light source for at least 5 minutes before touching. Luxtec manufactures its headlights to the highest quality standards. Each one is tested thoroughly before leaving the factory to ensure proper working conditions. These instructions should help you get started with your new Luxtec equipment, quickly and easily. If you have any problems, please contact the Luxtec Service Department: (800) 325 -8966, or +1(508) 835 -9700, Fax +1(508) 835 -9976. All Headlight Systems

To ensure long life for the headband, cable, and modules, they should be stored in the duffel bag provided.

Information contained in this manual is subject to change without notice.

6

U l t r aL i te ® P r o H ea d l i g ht S y stem

care and maintenance

REPLACEMENT PARTS For Xenon Ultralite® pro Part Number

Description

AX2000BIF

UltraLite® Pro headlight assembly with 9 ft (275 cm) bifurcated cable, Mark II module and gown clips

AX2000BIFSL

UltraLite® Pro headlight assembly with 9 ft (275 cm) bifurcated cable, Mark II module and gown clips with short

linkage 001370LX

UltraLite® Pro replacement headband

001380LX

Mark II module, black

001380LXSL

Mark II module, black, short linkage

001378LX9

UltraLite® Pro bifurcated fiber optic cable, 9 ft (275 cm)

001378LX11

UltraLite® Pro bifurcated fiber optic cable, 11 ft (335 cm)

001378LX7P5

UltraLite® Pro bifurcated fiber optic cable, 7.5 ft (230 cm)

001387LX

Replacement Pad kit, UltraLite® Pro headlight

Cleaning Modules

The headlight module may be wiped down with alcohol. The lens should be cleaned only with lens tissue available at any camera store. Follow the package directions. Follow all applicable bloodborne pathogen procedures as indicated by OSHA and/or your hospital requirements when cleaning and disinfecting. warning

• DO NOT soak the UltraLite® Pro cable in any sterilization solution.

Cleaning Headband

The headband may be cleaned by an alcohol wipedown or washed with lukewarm water and mild detergent. Cleaning Fiber optic Cable

Luxtec suggests that the use of alcohol wipes to clean the headlight cables. There is a lens assembly at the light source end, which is not sealed and could allow moisture to penetrate behind the lensing.

LUXTEC HEADLIGHT WARRANTY

Luxtec warrants that the equipment manufactured by Luxtec shall be free from defects in material and workmanship under normal use and service for a period of three (3) years, except the cable, from the date of shipment from Luxtec. Luxtec’s sole and exclusive liability under warranty shall be, at Luxtec’s option, either to repair or replace any component which fails during the warranty period due to any defect in workmanship or material F.O.B. factory if: 1. Customer promptly reports such defect to Luxtec in writing, 2. If requested by Luxtec, customer returns equipment to Luxtec with shipping charges and, 3. Upon inspection, Luxtec finds the equipment to be defective. This warranty is contingent upon normal and proper use of the equipment. It does not cover equipment modified without the written approval of Luxtec, subjected to unusual physical or electrical stress, or damaged during shipment. This warranty is nontransferable unless authorized in writing by Luxtec.

warning

Luxtec reserves the right to make design changes on its products without liability to incorporate said change in Luxtec products previously designed or sold.

warning

Upon receipt of the product, it should be carefully inspected. If any defect is discovered, notification must immediately be given to the manufacturer.

• DO NOT sterilize the UltraLite® Pro cable in any sterilization solution.

• DO NOT autoclave the headband, cables, or headlight modules troubleshooting

LUXTEC CABLE WARRANTY

For additional technical assistance, please contact the Luxtec Service Department, (800) 325 -8966, or +1(508) 835 -9700, Fax +1(508) 835 -9976.

7

Luxtec warrants that the cables furnished hereunder shall be free from defects in material and workmanship under normal use and service for a period of 18 months.

Information contained in this manual is subject to change without notice.

U l t r aL i te ® P r o H ea d l i g ht S y stem

return policy

REPAIR AND RETURN

Any device must be clean when returned to Luxtec. Luxtec reserves the right to return unrepaired any equipment that is contaminated with blood or other organic material. Warranty Service and Repair

To obtain service under warranty or return product for repair, the customer should contact the local Luxtec distributor or call Luxtec Customer Service at (800) 325-8966 or +1(508) 835-9700.

Information contained in this manual is subject to change without notice.

8

Three-point Comfort System

www.Integra-Surgical.com The Integra wave logo is a trademark of Integra LifeSciences Corporation. SIL-KORE is a trademark of W.L. Gore & Associates, Inc. UltraLite® and UltraLite® Pro are registered trademarks of Integra Luxtec, Inc. © 2009 Integra LifeSciences Corporation.

USA

Information contained in this manual is subject to change without notice.

P/N 850532 Rev B 03/09