Quick Start
2 Pages
![Liebel-Flarsheim OptiVantage DH TM Injection System General Fill Syringes The following guide describes the basic instructions to operate the OptiVantage in dual mode. In order to fill the syringe, the Powerhead must be tilted up in a position 60° or greater from horizontal in order to ensure optimum removal of air. The lighted knobs on the back of the injector will flash blue to indicate proper tilt angle. Power-up The unit can be powered up by either pressing the power-up button on the Console or by pressing and holding for a few seconds the touch screen on the Powerhead. Auto Fill Fill Volume (ml) 100 75 A B Start Auto Fill Start Auto Fill Fill Volume (ml) 0 25 50 75 100 125 150 175 200 Main 60o Air Purge Attach the “Y” tubing to the syringes using aseptic technique. Rotate the Powerhead vertically to allow air bubbles to rise to the tip to form an air pocket. Using either the expel arrow or the manual knob, advance the CONTRAST plunger to push CONTRAST just past the y-intersection of the “Y” tube. Advance the SALINE plunger to push SALINE past the y-intersection and out through the extension tubing. Auto Fill 200 mL Syringe Load the syringes into the Powerhead making sure the appropriate syringe is installed on the appropriate side. The user can select the side dedicated to contrast in the set-up screen from the Main Menu. A A A Flow (ml/s ec) e (ml) 158 Enab le lay Delay 0 Inject De D ela y ct 0 D je n P 20 SI 0 k S ca P ea In 8 ab le l) 8 (m 15 e m 83 15 l) n (m E Vo lu ) ec m e 73 on (m l/s Vo lu ) ati in ec m 0 4. lo w l/s xa 0 E (m lo w Liv er 4. F F A A B 0 Scan 4 Volum n (ml) 3 inatio Volum e Delay Delay 0 4 EXTEND RAM 4.0 73 ) 50 5 LEVER IN LOCK POSITION 2 Liver Exam (ml/sec) 0 PSI 20 Inject Scan 4.0 83 Flow Enable e (ml) Volum n e (ml) 158 inatio Volum Exam 5 UMBRELLA CAP IN LOCK POSITION 4.0 73 Liver (ml/sec) 4.0 83 Flow 2 TABS OPEN 1 RETRACT RAM A A All trademark rights reserved. 2004 Mallinckrodt Inc. Activating Fill/Expel Arrows B ! Read the Operators manual for complete instructions. 3 A This guide is intended as a quick reference. For detailed operational information read all OptiVantage DH Operator, Service, and Installation documentation before using procedures defined in this guide. Failure to follow this instruction may result in damage to equipment or possible personal injury. ela y 844965-A OptiVantag TM e DH Quick Reference Guide 200 mL syringes can be filled using the Auto Fill feature accessible only from the Powerhead screen. To activate the Auto Fill feature, tilt the Powerhead in a position 60° or greater from horizontal. Install the 200 mL syringe into the pressure sleeve. Rotate the lever to the lock position and the Auto Fill screen automatically appears on the Powerhead screen. Update the volume parameter as required. Press the [Start Auto Fill] key and the injector will automatically fill the syringe. (Note: The fill sequence intakes then expels approximately 25 mL of fluid, then fills to the required volume in order to limit air intake in the syringe.) A Load Syringes](https://images.bioclinicalservices.com.au/rTGzQJnxGsRSxvJwfCsdfskR/320w/Mallinckrodt%20-%20OptiVantage%20DH%20Quick%20Start%20Rev%20a.png)
Preview
Page 1
Liebel-Flarsheim
OptiVantage DH TM
Injection System
General
Fill Syringes
The following guide describes the basic instructions to operate the OptiVantage in dual mode.
In order to fill the syringe, the Powerhead must be tilted up in a position 60° or greater from horizontal in order to ensure optimum removal of air. The lighted knobs on the back of the injector will flash blue to indicate proper tilt angle.
Power-up The unit can be powered up by either pressing the power-up button on the Console or by pressing and holding for a few seconds the touch screen on the Powerhead.
Auto Fill Fill Volume (ml)
100 75
A
B
Start Auto Fill
Start Auto Fill
Fill Volume (ml)
0
25
50
75
100
125
150
175
200
Main
60o
Air Purge Attach the “Y” tubing to the syringes using aseptic technique. Rotate the Powerhead vertically to allow air bubbles to rise to the tip to form an air pocket. Using either the expel arrow or the manual knob, advance the CONTRAST plunger to push CONTRAST just past the y-intersection of the “Y” tube. Advance the SALINE plunger to push SALINE past the y-intersection and out through the extension tubing.
Auto Fill 200 mL Syringe Load the syringes into the Powerhead making sure the appropriate syringe is installed on the appropriate side. The user can select the side dedicated to contrast in the set-up screen from the Main Menu.
A
A
A
Flow (ml/s ec)
e (ml)
158
Enab le
lay
Delay
0
Inject De
D
ela y
ct
0
D
je
n
P
20 SI
0
k
S ca
P ea
In
8
ab le
l)
8
(m
15
e
m
83
15
l)
n
(m
E Vo lu ) ec
m
e
73
on (m
l/s
Vo lu )
ati in
ec
m
0
4.
lo w
l/s
xa
0
E
(m lo w
Liv er
4.
F
F
A
A
B
0
Scan
4
Volum
n
(ml)
3
inatio
Volum e
Delay
Delay
0
4 EXTEND RAM
4.0 73
)
50
5 LEVER IN LOCK POSITION
2
Liver Exam
(ml/sec)
0
PSI
20
Inject
Scan
4.0 83
Flow
Enable
e (ml)
Volum
n
e (ml)
158
inatio
Volum
Exam
5 UMBRELLA CAP IN LOCK POSITION
4.0 73
Liver
(ml/sec)
4.0 83
Flow
2 TABS OPEN 1 RETRACT RAM
A
A
All trademark rights reserved. 2004 Mallinckrodt Inc.
Activating Fill/Expel Arrows B
!
Read the Operators manual for complete instructions.
3
A
This guide is intended as a quick reference. For detailed operational information read all OptiVantage DH Operator, Service, and Installation documentation before using procedures defined in this guide. Failure to follow this instruction may result in damage to equipment or possible personal injury.
ela y
844965-A
OptiVantag TM e DH
Quick Reference Guide
200 mL syringes can be filled using the Auto Fill feature accessible only from the Powerhead screen. To activate the Auto Fill feature, tilt the Powerhead in a position 60° or greater from horizontal. Install the 200 mL syringe into the pressure sleeve. Rotate the lever to the lock position and the Auto Fill screen automatically appears on the Powerhead screen. Update the volume parameter as required. Press the [Start Auto Fill] key and the injector will automatically fill the syringe. (Note: The fill sequence intakes then expels approximately 25 mL of fluid, then fills to the required volume in order to limit air intake in the syringe.)
A
Load Syringes
Recall Protocol Parameters
PROTOCOL 2 Dr Jones
Page
2
6.0 3.0
75 14
13 600
A
1.0
75
13
3
12 600
2 4 6 2 4 6
4
ay el D
ay ak
ct je In
0
PS I
Sc 0 an D el
20
Pe
e bl
15 8
15 8
l)
E na
(m lu
m
e
73
Vo
n
l) (m
at io
e
in
m
83
l/s ec )
lu Vo
(m
Ex am r
ow
ve
(m
Li
l/s ec )
4. 0
Fl
A
4. 0
A
ow
Fl
Once the tubing is attached to the patient and the OptiVantage is enabled, the venous access can be checked using the Patency Check feature. Press the “Patency Check” button on the Powerhead screen while observing the injection site.
-
5
Main
Enable The operator is responsible for ensuring that all air has been completely evacuated from the syringe and tubing prior to delivering the injection. Review all parameters thoroughly to ensure they are correct and appropriate for the procedure. Also, ensure that the contrast fluid is installed on the correct side of the Powerhead. Tilt the Powerhead down at least 30° below horizontal The lighted knobs on the back of the OptiVantage will flash blue to indicate the proper angle.
Patency Check
RETRACT RAM
Start Patency
OptiBolus TM Option An OptiBolus injection can be set up by pressing the OptiBolus button located on the main screen.
Disable
Set-Up Screen
2.0
5
Flow (ml/sec)
Volume (ml)
B
Various options can be selected in the set-up screen. Injector Set Up
SEPT 02 2004 20:57 Software Versions
0
25
50
75
100
125
150
175
200
The OptiVantage injects a user defined amount of saline in order to determine that the venous access is clear. If extravasation is observed at the injection site, or other abnormalities are noticed, recheck the venous access and / or IV connections.
6
7
Console: DV00.00.01 Power Head: 00.00.01
OEM Interface: ZZZZ.ZZ.ZZ
OEM Interface
Control
Timing Bolus
Patency Check
On
Patency Check Volume
5
Drip Mode
On
Drip Flow Rate
0.5
On
Drip Volume
3.0
Drip Interval
1
Pause on Pressure Limit
Off
Pressure Limit
Auto
Pressure Units
PSI
Auto Fill
On
Set Up
5
P
18 18
-
B A
Feature
20 SI
2.0 4.0
2 4 6 2 4 6
Patency Check
In je ct D e 0 lay S ca n D e 0 lay
12 600
P ea k
13
18 18
8
75
2.0 4.0
The 200-mL syringes can be removed at any time. However, removal of the pre-filled syringe requires the ram to be fully retracted. The attached “Y” tubing must be removed prior to retracting the ram to prevent the syringe from drawing fluid. After the 200-mL syringe has been removed, move the ram to the fully extended position using the directional arrows on the Powerhead.
(m l)
1.0
A A -
B A
TM
15
A
12
Vo lu m e
13 600
18
8
75 14
2.0
15
5.0 3.0
B -
ab le
A A -
2 4 6 2 4 6
(m l)
13 600
Removing Syringes
E n
75 14
12
73
1.0 3.0
18
Vo lu m e
A A
2.0
on
1 3 5 1 3 5 1 3 5 1 3 5
B
Press the ENABLE button on either the Powerhead or the Console and the knobs on the back of the unit will light up yellow (for contrast) and purple (for saline).
83
13
12 600
ec )
75
18 18
ec )
1.0
2.0 4.0
0
A -
B A
(m l/s
13 600
12
F lo w
75 14
18
(m l/s
7.0 3.0
2.0
0
A A -
B
E xa m in ati
1 3 5 1 3 5
sec
2 4 6 2 4 6 2 4 6
F lo w
13
1 3 5 1 3 5
Memory 1
75
B
Store
The injection can be started from the Powerhead or the console by pressing the “Start” button. An optional coiled handswitch is available.
A
PROTOCOL 1
1.0
Starting the Injection
Liv er
LIVER Dr Fredrick
A -
30o
To remove the faceplates, move the injector rams to their fully retracted position. Using the manual knob, retract the ram an additional ¾ turn to unlock & remove. The faceplate will lift off.
4.
Dr Jim
1 3 5
Timing Bolus is set up as part of the protocol on the Console. Pressing the start button on the Console or the Powerhead activates the injection.
Removing Faceplates
A
proto1
A Timing Bolus injection is a user defined injection to determine the scan delay.
Miscellaneous
4.
Edit Name
Phase Side ml/sec ml sec Phase Side ml/sec ml
Timing Bolus TM Feature
A
Delete
3
B
Move
1
A
The user can recall a protocol from a library of 40 operator stored protocols from either the Console Memory key or the Powerhead Memory key. Recalled protocols can be modified. Modified protocols will have a asterisk located at the end of its name as a reminder to the operator. After modification press the protocol name to activate.
2
>
>
Time
Language
Service
8
Alarm
Main