TI-Max X X-SG65L and X-SG65 External Coolant Straight Handpiece Operation Manual Oct 2015

This handpiece is designed for clinical dental use and implant surgery.

CAUTION

ENGLISH

Intended Use

• Read this Operation Manual before use to fully understand the product functions and file for future reference. • When operating the handpiece always consider the safety of the patient. • Do not attempt to disassemble the handpiece nor tamper with the mechanism. • Check the vibration, noise and overheating outside the patient's oral cavity before use. If any abnormalities are found, stop using the handpiece immediately and contact your dealer. • Should the handpiece function abnormally, cease operation immediately and return the handpiece to the dealer for repair. • Do not allow any impact on the sheath. Do not drop the handpiece. • Always keep bur shanks clean. Dirt or debris in a chuck could cause poor bur concentricity or low chuck retention force.

0

1

(1) Connecting Push the handpiece on to the motor taking care to keep it in alignment. X-SG65L Only Twist the handpiece until it locks into position with a clicking sound. (2) Disconnecting Hold the motor and the handpiece, and pull it out.

2. Mounting and Removing Bur (1) Handpiece Bur Inserting the Bur 1) Turn the Bur Lock Ring in the direction of mark [O] until it clicks. 2) Insert the bur. 3) Turn the Bur Lock Ring in the direction of the mark [C] until it clicks. Make sure Black Dots align (Fig. 2). 2

Handpiece

Motor

Fig. 1

Bur lock ring Black Dots

Open

Align the Black Dots

Close

mark [C]

Fig. 2

(2) Contra-angle bur Inserting the Bur 1) Turn the bur lock ring in the direction of mark [O] until it clicks. 2) Insert the supplied Bur Stopper into the chuck. (Fig. 3) 3) Insert the Contra-Angle Bur until it stopped. 4) The bur will be chucked by turning the bur lock ring in the direction of mark [C] until it clicks and Black Dots line up. Removing the Bur Turn the Bur Lock Ring in the direction of mark [O] until it clicks and remove the bur. Remove the Bur Stopper 1) Turn the Bur Lock Ring in the direction of mark [O] until it clicks. 2) Insert the supplied Bur Stopper puller into the chuck. Pull out the Bur Stopper by hooking at the slit of Bur Stopper. (Fig. 4)

Bur Bur Stopper

Fig. 3

Bur Stopper Puller

Fig. 4

ENGLISH GERMAN FRENCH SPANISH ITALIAN

Removing the Bur Turn the Bur Lock Ring in the direction of mark [O] until it clicks and remove the bur.

1. Connection / Disconnecting the Handpiece and Motor

3

Heat Generation Problem • Bur position is improper or it is not mounted. --> Mount the bur correctly. • During operation, Bur Lock Ring had been turned. --> Do not turn the Bur Lock Ring while the handpiece is rotating. Bur Jump Out Problem • Incorrect mount of the bur/bur stopper. --> Mount the bur/bur stopper firmly. • During operation, Bur Lock Ring had been turned. --> Do not turn the Bur Lock Ring while the handpiece is rotating. 4

• Mount short shank contra-angle bur. --> Do not mount this bur. Bur Breakage Problem • Mount damage or sub-standard burs. --> Do not mount those burs. • Exceed drive motor speed or manufacture’s recommended bur speed. --> Do not exceed drive motor speed or manufacture’s recommended bur speed.

External Irrigation Nozzle

Irrigation Tube

Connect the irrigation tube to the external irrigation nozzle firmly.

4. Maintenance

Fig. 5

CAUTION After each patient, be sure to keep the handpiece after cleaning, lubrication, and sterilization. If the blood is left on the handpiece, it can be clotted causing rusty. Refer to the Maintenance Guide OM-Z0135E. This handpieces can be autoclavable up to Max.135°C. This handpieces can be cleaned and disinfected with a Thermo-Disinfector.

*Cleaning Clean the external irrigation nozzle inside with clean water.

ENGLISH GERMAN FRENCH SPANISH ITALIAN

3. External Irrigation Nozzle

CAUTION for Bur Usage

5

5. Cleaning the Glass Rod Optic

Cotton Swab

Clean the Glass Rod Optic with cotton swab soaked in alcohol.

Glass Rod Optic

Fig. 6

CAUTION Do not use a sharp tool to clean the glass rod optic. It could damage the glass rod optic and decrease the light transmission. If it becomes dim, contact your dealer.

6

Model Gear Ratiio

X-SG65L 1:1

Bur applied Length

40,000 min -1 (rpm) ø2.35mm Handpiece Bur and ø2.35mm CA Bur 29.4mm (Handpiece Bur)

Max Bur Length

44.5mm (Handpiece Bur)

Max Bur diameter

Ø4.0

Allowable Max Speed Bur

X-SG65

Irrigation

External Irrigation

Optic

Glass Rod

SPECIFICATION

ENGLISH Specification

-

Use Environment

Temperature : 0 – 40 ˚C, Humidity : 30 - 75% HR, Atmospheric Pessure : 700 - 1,060hPa

Transportation and Storage Environment

Temperature : -10 – 50 ˚C, Humidity : 10 - 85% RH, Atmospheric Pessure : 500 - 1,060hPa

31

OM-H0190E 002

2021-08-XX CACB09XX XXN