NSK
I-Type Surgical Attachment Shank Operation Manual
2 Pages
Preview
Page 1
I-Type Surgical Attachment Shank
ER16i/ER20i/ER32i/ER64i/ER256i
OM-C0350E 001
Caution • Always consider safety of the patient first, and do not abuse. • The handpiece is designed for dental clinical or surgery use. Do not use it for the other purposes. • When it is found abnormal during use, stop immediately. Do not use, and report to the dealer that was purchased from. • Do not disassemble the sheath except for the referred to herein, nor alter. • Do not impact on the sheath, nor drop onto hard surface. • Always watch for vibration, sound, temperature rise, bur wobble, and other abnormalities. • Disconnect the sheath after the driver unit is in complete stop. • The device accepts NSK I-type heads. • Do not wipe with, or clean or immerse in, high acid water or sterilizing solutions. • After each operation, be sure to keep the handpiece after cleaning, lubrication, and sterilization. If the blood is left on the handpiece, it can be clotted causing rusty. • Do not wipe with, or clean or immerse in, high acid water or sterilizing solutions.
1. Speed Allowable Max.Speed (Motor) ········· 40,000min-1 (rpm) Sheath Type
Motor Speed
Bur Speed (min-1) ER16i
ER20i
ER32i
ER64i
ER256i
40,000
2,500
2,000
1,250
625
156
30,000
1,875
1,500
938
469
117
20,000
1,250
1,000
625
313
78
10,000
625
500
313
156
39
(min-1)
Note: The bur speed might be slightly lower than the theoretical speed as given above, due to a loss at the gear train.
2. Heads All NSK I-type heads fit the sheath. Set the head as shown in Fig.1 for alignment, and securely fasten the head nut. Head
Union Nut
ER20i Head shows SGM.
Fig.1
3. Lubrication Supply PANA SPRAY Plus / PANA SPRAY after each use and/or before autoclaving. 1 Mount the Surgical Head spray nozzle into the spray port. 2 Shake the can 3-4 times to well mix lubricant and propellant. 3 Insert the surgical head spray nozzle in the rear of the handpiece and
spray for approximately 2-3 seconds until the oil comes out of the handpiece head. Surgical Head Spray Nozzle
PANA SPRAY Plus / PANA SPRAY
Handpiece
PANA SPRAY Plus / PANA SPRAY Fig.2
Cautions on Lubrication • Be sure to hold the handpiece firmly to prevent the handpiece from slipping out by the spray pressure when lubricating. • Keep the PANA SPRAY Plus / PANA SPRAY can upright.
4. Cleaning and Sterilization
Caution After each operation, be sure to keep the handpiece after cleaning, lubrication, and sterilization. If the blood is left on the handpiece, it can be clotted causing rusty. This handpiece can be washed via Thermo Disinfector. Sterilization by autoclaving is recommended. Sterilization is required first time you use and after each patient as noted below. Autoclaving procedure 1 Brush off dirt and wipe clean with alcohol-soaked cloth or paper towel. 2 Remove reduction sheath from the motor and lubricate. Ref.3 Lubrication. 3 Insert into a sterilization bag and seal it. 4 Autoclavable up to max. 135˚C. ex.) Autoclave for 20 min. at 121˚C, or 15 min. at 132˚C. 5 Keep the handpiece in the autoclave pouch to keep it clean until you use it. Sterilization at 120˚C for more than 15 minutes is recommended by EN13060.
Cautions on Sterilization • Heating element may be located at the bottom of the chamber, and the temperature there locally may exceed the set value. Place the handpiece on the central or upper tray. • Do not autoclave the handpiece, even when it is bagged, together with other instruments, from which chemicals are not sufficiently cleaned. This is to avoid discoloration and/or damage the plating of the handpiece.
’09.04.005 S