Nutricia
Flocare F800 Enteral Feeding Pump Short Manual
Short Manual
2 Pages
Preview
Page 1
Flocare 800 Short Manual
ENTERAL FEEDING PUMP RATE ML/HR
RUN
HOLD
VOL FED
DOSE
DOSE COMPLETE OCCLUSION NO FLOW LOW BATTERY
DEC
INC
MALFUNCTION AC POWER
Preparation and start of the pump
800
800
RUN
HOLD
VOL FED
DOSE
RATE ML/HR
MALFUNCTION
HOLD
OCCLUSION NO FLOW
VOL FED
DOSE
RATE ML/HR
INC
DEC MALFUNCTION
OCCLUSION NO FLOW
HOLD
VOL FED
DOSE
RATE ML/HR
INC
MALFUNCTION
INC
OCCLUSION NO FLOW
HOLD
VOL FED
DOSE
LOW BATTERY
DEC
MALFUNCTION
AC POWER
1
RUN
DOSE COMPLETE
LOW BATTERY
DEC
AC POWER
AC POWER
ENTERAL FEEDING PUMP
RUN
DOSE COMPLETE
LOW BATTERY
LOW BATTERY
800
ENTERAL FEEDING PUMP
RUN
DOSE COMPLETE
DOSE COMPLETE OCCLUSION NO FLOW
800
ENTERAL FEEDING PUMP
ENTERAL FEEDING PUMP RATE ML/HR
2
INC
DEC
AC POWER
3
4
1
> Insert the drip chamber of the feeding set into the drip detector slot of the pump.
2
> Slowly open the roller clamp on the feeding set and allow the total set to fill with feed. Make sure the drip chamber is filled up about one-third.
3
> Stretch the tubing around the pump wheel and insert the plastic retainer into the bracket on the pump.
4
>ENTERAL PullFEEDING the PUMP tubing through the tubing guide. RATE ML/HR
RUN
HOLD
VOL FED
DOSE
Connect the feeding set to your tube and continue to operate the pump. DOSE COMPLETE OCCLUSION NO FLOW
Operating instructions LOW BATTERY ENTERAL ENTERAL FEEDING FEEDING PUMP PUMP
DEC
MALFUNCTION RATE ML/HR RATE ML/HR
RUN RUN
HOLD HOLD
VOL VOL FED FED
DOSE DOSE
INC
AC POWER Turning on DOSE DOSE COMPLETE COMPLETE OCCLUSION the pumpOCCLUSION NO FLOW NO FLOW
> Turn on the pump by pressing the “POWER/ON” key. The pump is in “HOLD” mode.
LOW BATTERY LOW BATTERY
DEC DEC Programming > Set the desired flow rate (ml/h) by pressing the “INC” or “DEC” keys. INC INC MALFUNCTION MALFUNCTION ENTERAL FEEDING PUMP ENTERAL ENTERAL FEEDING FEEDING PUMP PUMP Continuous Feeding > Flow rates can be set from 1 to 300 ml/h, in 1 ml increments. AC POWER AC POWER ENTERAL PUMP RATEFEEDING ML/HR RUN HOLD RATE ML/HR RATE ML/HR RUN RUN HOLD HOLD > Press the “RUN” key to start the pump. DOSE COMPLETE RATE ML/HR DOSE DOSE COMPLETE COMPLETE
RUN
HOLD VOL FED DOSE DOSE
DOSE > After programming the flow rate do not immediately press the “RUN” key. > Press the “DOSE” key to set the desired dose. DEC INC DEC ENTERAL FEEDING PUMP DEC > Press “INC” or “DEC” to program the correct dose (in ml). MALFUNCTION INC INC LOW BATTERY MALFUNCTION MALFUNCTION DEC INC RATE ML/HR RUN HOLD > Press the “RUN” key to start the pump. MALFUNCTION AC POWER
OCCLUSION VOL VOL Programming DOSE COMPLETE NO FLOW OCCLUSION OCCLUSION FED FED NO FLOW NO FLOW VOL OCCLUSION LOW BATTERY Dose Feeding FED NO BATTERY FLOW LOW LOW BATTERY
DOSE
ENTERAL FEEDING PUMP AC POWER AC POWER DOSE COMPLETE AC POWER VOL RATE ML/HR OCCLUSION HOLD ENTERALRUN FEEDING PUMP FED NO FLOW ENTERAL FEEDING PUMP DOSE COMPLETE LOWML/HR BATTERY RATE RUN VOL OCCLUSION DOSE INC FED RATE ML/HR RUN NO FLOW MALFUNCTION DOSE COMPLETE VOL LOW BATTERY OCCLUSION DOSE COMPLETE AC POWER FED DEC NO FLOW INC VOL MALFUNCTION OCCLUSION FED NO BATTERY FLOW LOW
Changing Programming
DOSE > Press “HOLD” key, pump will stop, all memory and programming is retained. Use this to: change flow rate, alter dose setting, change feed, administer medication. HOLD DEC HOLD > Press “RUN” to restart the pump.
Viewing total volume delivered AC POWER MALFUNCTION LOW BATTERY
DOSE > Press “VOL FED” key, display will indicate total volume delivered.
MALFUNCTION AC POWER
Turning off the pump
AC POWER
INC INC
DOSE
DEC DEC
> Turn on the pump by pressing the “OFF” key for ca 3 seconds.
Flocare 800 Problem solving instructions Error messages and instructions Please refer to detailed Instructions for Use for additional information Problem/Alarm
Likely cause
Instructions
HOLD
> The pump has been left in “hold” mode for 3.5 minutes.
> Reset the alarm by pressing the “HOLD” key, or > Continue feeding by pressing the “RUN” key.
SET
> The feeding set is incorrectly placed.
> Press the “HOLD” key, insert the plastic retainer into the bracket on the pump, and then “RUN”.
DOSE COMPLETE
> The pump has finished administering the programmed dose.
> Switch the pump off by pressing “OFF” key, or > Program the pump to administer a repeat dose by pressing “HOLD” and then “RUN”.
> The feeding container is empty.
> Change the feeding container or switch off the pump.
> The liquid level in the drip chamber is too high.
> Remove the set from the pump; hold the set upside-down so that feed runs back in to the container, until the chamber is ca. one-third full. Reload the set.
> The sensor area is dirty.
> Remove the drip chamber from the slot and clean the drip detector sensors with a damp cotton swab.
> There is an obstruction to flow, either in the feeding set or in the tube.
> Check the feeding set, ensure that the roller clamp is fully opened and that there are no kinks in the tubing, and/or > Remove the set from the pump and check if feed is flowing from top to bottom (with the roller clamp open), and/or > Check if your tube is clogged by flushing the tube.
LOW BATTERY
> Ca. 30 minutes of battery time remain.
> Connect the pump to the mains and charge the pump. During charging the pump can be used.
MALFUNCTION (E-1 to E-11)
> The pump needs repair.
> Contact your healthcare practitioner.
OCCLUSION NO FLOW
171102 / BP&MC 11090802