14 Pages
Preview
Page 1
NuVasive Specialized Orthopedics, Inc. Precice® Bone Transport System Instructions for Use Product Description: The Precice Bone Transport System is composed of an implantable intramedullary nail, locking screws, reusable instruments, and a hand-held External Remote Controller (ERC). The Precice Bone Transport System is a sterile, single-use device that is surgically implanted using the instruments and locking screws for osteoplasty lengthening and bone transportation utilizing distraction osteogenesis and compression. The Precice Bone Transport implants are manufactured from stainless steel (BioDur 108 Alloy) per ASTM F2229. The ERC is used daily after implantation to non-invasively adjust the position of the distraction rod. During the implantation procedure, the nail can be adjusted to provide an appropriate amount of compression or distraction for transport of the intercalary segment to the docking segment. Following implantation, the Precice Bone Transport System utilizes distraction osteogenesis to lengthen the bone. Traditional intramedullary surgical techniques are used to implant and secure the proximal, distal and intercalary sections of the Precice Bone Transport nail to the target bone. The Precice Bone Transport nail includes a small internal magnet and gearing. After positioning the External Remote Controller (ERC) against the skin over the internal magnet, activation of the ERC causes the magnet to rotate and either retract or distract the distraction rod of the nail. During the surgical implantation procedure and after the nail has been secured to the bone, the distraction rod can be adjusted up to 100mm for femoral and tibial implants to transport and compress the intercalary segment to the docking segment. Over a period of days, weeks, or months, sequential compressions or distractions are used to transport and compress the intercalary segment to the docking segment of the bone to promote healing of the bone. The Precice Bone Transport nail remains implanted until bone consolidation has been completed. Once the physician determines that the nail has achieved its intended use and is no longer required, it is removed using standard surgical techniques. Intended Use: The Precice Bone Transport System is intended for limb lengthening, open and closed fracture fixation, pseudoarthrosis, mal-unions, non-unions, or bone transport of long bones. Contraindications: • Infection or pathologic conditions of bone such as osteopenia which would impair the ability to securely fix the device. • Patients with Gustilo open fracture Classification Grade IIIB or IIIC fractures • Patients with pre-existing nerve palsies • Metal allergies and sensitivities. • Patients with an irregular bone diameter that would prevent insertion of the Precice Bone Transport nail. • Patients in which the Precice Bone Transport nail would cross joint spaces or open epiphyseal growth plates. • Patients with conditions that tend to retard healing such as blood supply limitations, peripheral vascular disease or evidence of inadequate vascularity. • Patients unwilling or incapable of following postoperative care instructions. • Patients with maximum bone defect of more than 100 mm. • Patients with excessive skin damage and inadequate soft tissue covering of the fracture sites. LC0262-J 6/2022
1 |Page
Please refer to the table below for contraindications with regard to weight and maximum distance of the treated limb to the surface of the intramedullary canal.
Limb
Precice® Bone Transport Model
Tibia
Femur
C, SJ A, B, BT, D, DT, E, V, X, SE, SB, SD, SA
Nail Diameter (mm) 10.0 11.5 13.0 10.0 11.5 13.0
Maximum Maximum Distance of Max. Patient Max. Patient Distance of Treated Limb Weight Bearing Weight Bearing Treated Limb Surface to IM Use with partially Use with fully Surface to IM Canal (ERC1, threaded screws threaded screws Canal (ERC4P) ERC2P, ERC3P) 13mm 19mm 25lbs/11kg 25lbs/11kg 13mm 19mm 190lbs/86kg 125lbs/57kg 13mm 19mm 250lbs/114kg 125lbs/57kg 51mm 64mm 25lbs/11kgs 25lbs/11kg 57.2mm 69mm 190lbs/86kg 125lbs/57kg 125lbs/57kg 76mm 85mm 250lbs/114kg
Warnings: •
• •
• • • • • • • • • •
•
• •
The Precice Bone Transport System cannot withstand the stresses of full weight bearing. The patient should progressively weight bear and use assistive devices as directed by the physician. Patients should utilize external support and/or restrict activities as directed by the physician until consolidation occurs. Patients with an open fracture may also have soft tissue damage as a result of severe trauma. It is important that soft tissue damage is addressed prior to procedure to minimize the risk of infection. The surgeon should closely monitor lengthening progress particularly for longer bone segments or mobilization lengths to prevent incomplete transport. The surgeons should account for potential difficulty in removal of the nail due to ingrowth into the slot feature of device. Do not use if the sterile packaging has been damaged or appears to have been previously opened. Metallic implants can loosen, fracture, corrode, migrate, or cause pain. Due to the presence of a magnet, use of the Precice Bone Transport System is not recommended in patients with pacemakers. The Precice Bone Transport System may not be appropriate for patients with poly-trauma. Use of the Precice Bone Transport System in patients with an active infection of the treated bone is not recommended. Overream the medullary canal by 2 mm to allow the transported segment to move freely over the nail. Patients treated with Precice Bone Transport may need secondary surgery to ensure union at the distal docking site. Smoking, chronic steroid use and the use of other anti-inflammatory drugs have been determined to affect bone healing and could potentially have an adverse effect of the bone regenerate during the lengthening process. The Precice Bone Transport nail is supplied sterile and is for single-use only. The nail has not been tested to be cleaned or sterilized for multiple uses. If the nail is used more than once, the device may not be sterile and could cause a serious infection. The Precice Screws may be provided sterile or non-sterile, take careful note to read packaging if screw is provided sterile or non-sterile. Before removing the implants from the package, make sure that the protective packaging is LC0262-J 6/2022
2 |Page
unopened and undamaged. If the packaging is damaged, the implants have to be considered as NON-STERILE and may not be used. • Note the STERILE expiry date. Implants with elapsed STERILE expiry dates have to be considered as non-sterile • Patients with implanted Precice Bone Transport nail should not enter an MRI unit.
• •
The Precice Bone Transport System is unsafe in Magnetic Resonance Imaging environments. There is a possibility of nerve or soft tissue damage and/or weakness related to either surgical trauma or the presence of the implant. Advise the patient to notify the surgeon of any experienced pain, numbness, or weakness while undergoing treatment.
Precautions: • •
•
•
It is recommended that ancillary fixation (e.g. plates, external fixation, cable and pulley system etc.) bridges the defect site. Do not use this device without proper training in both device implantation and adjustment. Refer to External Remote Controller (ERC, ERC 2P, or ERC 3P) Operator’s Manual (OM0005, OM0009, OM0016, or OM0017) for operation of the External Remote Controller. Prior to bone consolidation, the patient should not participate in contact sports or other high risk activities that will cause more than 20% of the body weight to be loaded on the treated limb. These activities may resume upon sufficient bone consolidation, but only as directed by the physician. Examine all Precice® Bone Transport System components carefully prior to use to assure proper working condition. If you suspect a component to be faulty or damaged, do not use.
Cautions: • • •
•
• •
The Precice Bone Transport System is for prescription use only by the order of a physician. Device is recommended to be removed after implantation time of no more than one year. Utilize extreme caution when handling instruments made from magnetic materials such as stainless steel in proximity of the magnet of the Precice Bone Transport nail, as materials will be attracted to each other. After the surgical procedure is complete, if retraction is needed during the lengthening or consolidation phase, retract the device no more than the amount lengthened the preceding day. Do not bend the Precice Bone Transport nail or otherwise modify or damage the implant. Follow the ERC Operators Manual (OM0005, OM0009, OM0016, or OM0017) to assure proper alignment between the ERC and magnet of the Precice Bone Transport nail.
LC0262-J 6/2022
3 |Page
Stainless Steel Locking Screw Compatibility Nail Diameter (mm)
Screw Position
Screw Diameter
10.0 11.5 13.0
Proximal Locking/ Distal Locking
5.0 mm
10.0 11.5 13.0
Distraction Rod
3.5 mm
Screw Type
Screw Lengths (mm)
Partial Thread
20-80
Full Thread
20-100
Partial Thread
20-60
Procedures Careful pre-operative diagnosis and planning, meticulous surgical technique, and extended postoperative care by experienced surgeons are essential to procedure success. Prior to use, the surgeon should be specifically trained in the use of the Precice® Bone Transport System along with the associated instruments to facilitate correct selection, placement and security of the implant.
LC0262-J 6/2022
4 |Page
Implantation Procedure For transport applications: 1. Thoroughly clean the instruments according to the parameters in Table 1 or 2 prior to sterilization. 2. Inspect the instruments after cleaning to check for damage prior to sterilization. Functional check should include ensuring mating instruments can be properly assembled and instruments with moving parts are operated to ensure correct operation. 3. Sterilize locking screws (if provided non-sterile) and instrument trays prior to the procedure. The Precice Bone Transport Nail is provided separately in sterile packaging. The Precice Screws are provided non-sterile or sterile, check labeling before proceeding. 4. Position patient per standard technique. 5. Check for length and rotation by comparison to the unaffected limb. 6. Intra-articular fracture components should be addressed with inter-fragmentary screw fixation prior to nail insertion. Care should be taken to place the screws in the anterior and posterior aspect of the distal long bone and safely out of the nail’s intended path. 7. Resect the affected bone segment using standard surgical technique. Prepare the bone ends perpendicular to the anatomical axis to allow for bone contact during the docking phase. 8. Determine the appropriate nail size and configuration to be used. • The length and position of the intercalary slot is dependent on the implant length. It is recommended to select an implant length that will provide the appropriate amount of transport distance needed for the procedure, as well as facilitate the appropriate position of the corticotomy. The Precice Fast Distractor (ref. LC0251) may be used to position the distraction rod to the optimal position 9. Use standard surgical techniques to provide for adequate venting of the intramedullary canal during surgery. 10. Identify and access the appropriate entry point for the delivery technique chosen (i.e., antegrade or retrograde). 11. After accessing the insertion site, use an awl or sterile entry drill to open the medullary canal. Use care to keep the straight part of the shaft of the instrument parallel to the long axis of the bone shaft. 12. If using flexible reamers, insert a guide wire into the medullary canal and advance until the tip of the wire reaches the intended location. Imaging in two planes is required while advancing the guide wire. 13. Ream the intramedullary canal sequentially in half millimeter increments to 2 mm larger than the selected nail diameter. 14. Secure the appropriate Bone Transport Template Nail (Bent or Straight) to the Drill Guide using the locking bolts. 15. Insert the assembled Template Nail into the medullary canal under image intensification. Advance the Template Nail until the device is properly positioned. Using a drill bit, locate the planned corticotomy location and make an entry hole through the bone to mark the location. 16. Withdraw the Template Nail and disassemble it from the Drill Guide. Complete the corticotomy using osteotomes and verify the corticotomy is completely circumferential. 17. Secure the Precice Bone Transport Nail to the Drill Guide using the locking bolts and tightening down the Locking Bolt and Impactor with a tommy bar or 6mm driver. Insert the assembled implant into the medullary canal under image intensification until the implant is properly positioned. 18. Using the Drill Guide mounted to control alignment, secure the proximal portion of the nail using proximal locking screws of appropriate length. The head of the screw should be flush with the bone surface. Do not drill additional holes until securing the previous locking screw. 19. Using a free hand technique and fluoroscopic imaging, secure the distal portion of the nail using distal locking screws of appropriate length. The head of the screw should be flush with LC0262-J 6/2022
5 |Page
the bone surface. 20. Using a free hand technique and fluoroscopic imaging, secure distraction rod using locking screws of appropriate length. The head of the screw should be flush with the bone surface. • If the transport requires the use of both intercalary slots of the nail, then only the proximal intercalary screw is used during the transport phase. An additional surgery will be needed during the transport phase to exchange the position of the intercalary screw. 21. Ancillary fixation should be used to bridge the defect site. Select one or more of the ancillary fixation options based on patient anatomy, location of defect and patient history. While using a supplemental plate as ancillary fixation, blocking screws should be placed using a free hand technique and fluoroscopic imaging. Note that the Bone Transport Templates should not be used during placement of blocking screws as the template diameter is less than the Precice Bone Transport implants. The supplemental plate should be fixated after both the Precice® Bone Transport device and blocking screws are placed. It is advised that the locking screws of the plate are inserted anterior to the device. External fixation or cable and pulley system could be used in conjunction with the Precice Bone Transport device for larger segmental defects at surgeon’s discretion. 22. Remove the Drill Guide and associated accessories and carefully irrigate to remove any remaining bone fragments. Attach the End Cap to the proximal end of the Precice Bone Transport Nail. Carefully irrigate the surgical site to remove any remaining bone fragments. 23. Disassemble the Drill Guide in reverse order from Step 14 prior to cleaning. Clean instruments after use, without allowing instruments to completely dry prior. 24. Locate the center of the implanted magnet and mark with indelible marker. 25. Close and dress the site using standard techniques. 26. Instruct the patient to maintain the indelible marker mark at the same location. Screw Exchange Procedure Depending on the segmental defect, both intercalary slots might be required. Below are the detailed steps to utilize the second intercalary slot.
Nail Length (mm) 280 300
NOTE: Defects less than 70mm do NOT require a screw exchange procedure. Max Defect Size (mm) Max Transport before Housing Tube Intercalary Slot Configuration Screw Exchange (mm) 60 60* 50 70 70* 50
320
80 70
340
90
360
100
50 70 50 70
380
100
400
100
50 70 50 70
*Screw exchange not required. LC0262-J 6/2022
6 |Page
1. If both intercalary slots are needed to complete the full transport distance, the progress should be checked regularly under fluoroscopy to monitor when the intercalary screw has reached the end of the first intercalary slot. 2. Verify the second locking hole in the distraction rod is visible within the second intercalary slot. 3. Using a free hand technique and fluoroscopic imaging, secure the second locking hole of the transport rod using a locking screw of appropriate length. The head of the screw should be flush with the bone surface. 4. Remove the first intercalary locking screw. Close and dress the site using standard technique, and resume transport according to the Post-Operative Procedures. • Note: It is important that the screw exchange is performed in the specified order, to maintain the fixation and position of the intercalary segment. Post-Operative Procedures 1. Read the External Remote Controller (ERC) Operator’s Manual (OM0005, OM0009, OM0016, or OM0017) prior to performing an adjustment of the Precice® Bone Transport nail. 2. Determine the amount of adjustment required to compensate for any length discrepancy between the treated limb and the unaffected limb or any additional compression or distraction desired. 3. Identify the mark on the limb where the magnet in the Precice Bone Transport nail is located. Carefully place the ERC firmly but comfortably over this area in the correct orientation. 4. Shorten or lengthen the implant to the desired amount, as programmed by the physician and viewed on ERC display screen. 5. Carefully place the ERC back in its storage container and close. 6. The progress should be checked regularly against follow-up radiographic evidence of the rate of transport and the quality of the regenerate. While 1 mm per day is generally recommended, clinical and radiographic examination may show that transporting should progress at a faster or slower pace. Weekly X-ray imaging to assess actual transport length is recommended. Implant Removal Procedures 1. At the time deemed appropriate by the physician, remove the Precice Bone Transport nail using standard surgical technique. 2. Follow all cleaning and sterilization procedures to prepare the instruments prior to removal. 3. Access the proximal end of the Precice Bone Transport nail and attach the removal instrumentation. 4. Remove one distal locking screw. Using the Precice Bone Transport removal instruments, insert the retention plug into the vacant hole. Confirm full seating of the retention plug under fluoroscopy. Once correct placement and complete seating is confirmed, the remaining screws can be removed. 5. Once all the locking screws have been removed, the Precice Bone Transport nail can be removed by using the removal tool assembly which consists of the locking rod, removal rod and the slap hammer. Disassemble removal tool assembly prior to reprocessing after the removal surgery. 6. Close and dress the wound using standard surgical techniques. 7. Return the explanted product to NuVasive Specialized Orthopedics, Inc. following instructions provided. Please call 1-855-435-5477 to obtain instructions or if you have any questions.
LC0262-J 6/2022
7 |Page
Cleaning and Sterilization Instructions The Instrument Tray, Locking Screw Tray, and instruments are provided non-sterile and must be cleaned and sterilized prior to use. Cleaning Instructions: Thoroughly clean and inspect the trays and instruments for damage prior to loading, wrapping, and sterilization. Disassemble the Instrument Tray and Locking Screw Tray by removing the lid from the tray base. Remove the instruments from the instrument holders. Note: Do not allow instruments to completely dry prior to cleaning. The recommended cleaning instructions for the Instrument Tray, Locking Screw Tray, and instruments are as follows: Table 1: Manual Cleaning Recommendations:
Time (Minutes)
Step
Solution
1
pH Neutral Hospital Grade Enzymatic Detergent
14-15 Minutes
Room Temperature
2
pH Neutral Hospital Grade Enzymatic Detergent
As required per detergent instruction
Room Temperature
3
Distilled or Reverse Osmosis (RO) Water
2-3
Warm, as delivered from hot water tap
4
pH neutral hospitalgrade enzymatic detergent
15 Minutes
LC0262-J 6/2022
Temperature
40-60°C
Instruction Disassemble instrument trays, remove the instruments from the instrument holders, and disassemble instruments before immersing, soaking, and performing the cleaning. Immerse and soak for required time. Clean thoroughly. Scrub all external surfaces with a soft bristle brush until all visible soil has been removed. It is important to make sure all areas of the tray and instruments are cleaned. Ensure that the holes and lumens are effectively cleaned by using a small diameter brush (tightfitting, soft and non- metallic) or pipe cleaner to clean holes and lumens. Inspect for visible soil on exposed surfaces. Pay attention to threads, hinges and occluded areas of the instrument trays and instruments, and any hard- to-reach areas. Inspect for visible soil on exposed surfaces and make sure there is no visible soil on the exposed surfaces. Rinse thoroughly for required time immediately after Step 2. Ensure water flows through all surfaces, perforations, holes and lumens. Inspect for visible soil on exposed surfaces and make sure there is no visible soil. Particular attention should be given to surfaces, perforations, lumens, hinges, and holes. Immerse and sonicate the instruments for the required time. The instrument trays do not require sonication.
8 |Page
5
Distilled or RO water
2-3
Warm, as delivered from hot water tap
6
Air
As required
Ambient
LC0262-J 6/2022
Rinse thoroughly for required time immediately after Step 4. Ensure water flows through all surfaces, perforations, holes, and lumens. Visually inspect the trays and instruments for visible soil or detergent. Particular attention should be given to surfaces, perforations, lumens, hinges, and holes. Tools such as lighting, magnifying glass, or boroscope may be used to inspect lumens or holes for visible soil. Perform an additional rinse if soil or detergent is still present and visually inspect. Repeat cleaning process if soil or detergent is still present. Allow to air dry in clean area. Blow perforations, holes, and lumens or any internal areas with clean air using filtered air source or syringe.
9 |Page
Table 2: Automatic Cleaning Recommendations:
Step
Solution
Time (Minutes)
1
pH Neutral Hospital Grade Enzymatic Detergent
As required
2
pH neutral hospitalgrade enzymatic detergent
15 Minutes
3
4
Distilled or reverse osmosis (RO) water
N/A
Temperature
Instruction
Room Temperature
Disassemble instrument trays, remove the instruments from the instrument holders, and disassemble instruments before immersing, soaking, and performing the cleaning. For instruments or trays with complex design features such as perforations, lumens, holes, threads or a hard to reach area, it is necessary to soak the instruments and manually scrub all external and internal surfaces with a soft bristle brush, a small diameter brush (tight-fitting, soft and non-metallic) or pipe cleaner until all visible soil has been removed prior to automatic reprocessing to improve the removal of adherent soil.
40-60°C
Immerse and sonicate the instruments for the required time by the manufacturer. The instrument trays do not require sonication.
2-3
Warm, as Rinse thoroughly for required time immediately delivered from after Step 2. Ensure water flows through all hot water tap surfaces, perforations, holes and lumens.
N/A
N/A
Load the lid, tray base, and insert tray such that all surfaces of the trays are exposed to the cleaning solutions. Load the instruments so that cannulations, lumens or holes can drain. Do not place heavier instruments on top of delicate instruments.
Distilled or RO Water pH Neutral Hospital Grade Enzymatic Detergent Distilled or RO Water
6
Cold
Pre-wash
10
55°C
Wash
30
N/A
Rinse
8
Distilled or RO Water
5
93°C
Final Rinse
9
N/A
Vary
Room Temperature
5
6
7
10
N/A
LC0262-J 6/2022
N/A
N/A
Dry Visually inspect the trays and instruments for dryness and visible soil or detergent. Particular attention should be given to surfaces, cannulas, hinges, lumens or holes. Tools such as lighting, magnifying glass, or boroscope may be used to inspect long cannulas, lumens or holes for visible soil. If soil or detergent is visible, repeat cleaning.
10 | P a g e
Sterilization Instructions: After cleaning the instrument tray and instruments, prior to sterilization, inspect all parts of the tray and instruments for damage. A functional inspection should also be performed where possible. Mating devices should be checked for proper assembly and devices with moving parts should be operated to check for correct operation. Load the base tray with the specified instruments or locking screws and secure the tray lid. Ensure that the tray base and lid can be secured using the latches and handles. If you suspect the tray or an instrument to be damaged, do not use the tray and/or instrument and contact NuVasive Specialized Orthopedics, Inc. for a replacement and/or repair. The Instrument and Locking Screw Trays have been qualified to be sterilized in a double wrapped configuration with a legally marketed, FDA cleared sterilization wrap (Such as CSR Wrap), using the following steam sterilization cycle: Table 3: Double Wrapped Sterilization Recommendations:
Sterilization Temperature
Sterilization Time (Minutes)
Drying Time (Minutes)
Maximum Tray Weight
132° C
4
Minimum 40
25 lbs
Pre-vacuum steam sterilization cycle
The Instrument Tray has also been qualified to be sterilized using Aesculap Rigid Containers, US only, using the following configurations and steam sterilization cycle: Table 4: Aesculap Container Configurations
Base Options Description Solid Bottom 4.75"
Aesculap NUVA PN JK442B (screen printed) JK442 (laser marked)
Nuva PN DM-JK442B DM-JK442B
Lid Options Description Aluminum Lid (Purple) Aluminum Lid (Silver)
Aesculap NUVA PN XG349 JK489B
Nuva PN 8803001 8803002
Table 5: Aesculap Rigid Container Sterilization Recommendations:
Pre-vacuum steam sterilization cycle
Sterilization Temperature
Sterilization Time (Minutes)
Drying Time (Minutes)
Maximum Tray Weight
132° C
4
Minimum 40
25 lbs
Precaution: When sterilizing instruments and locking screws, do not load the tray more than the weight specified in Table 3 or 5 above. Limits of Reuse: The instrument trays are reusable and actual limits of reuse for the instrument trays are based upon the proper handling, use, care and cleaning of the trays. The end of tray life is to be determined by wear and damage due to use and through the inspection of the trays after the cleaning and sterilization cycles. Discontinue use of the device if visible signs of wear are present. This includes cracking, peeling, flaking, rusting, and/or discoloration. Always inspect the instrument trays and its components between uses. For trays and instruments that are no longer functional, or exhibit excessive wear and tear, please return them to NuVasive Specialized Orthopedics for replacement. LC0262-J 6/2022
11 | P a g e
Storage: Recommended storage of the Instrument Tray is at controlled ambient temperature 20°-24°C (68°75°F). Ensure that the sterilized tray is stored in areas that provide protection from dust, moisture, insects, and extremes of temperature and humidity.
MRI Information: • •
The Precice® Bone Transport System is MR Unsafe. A patient with the implanted Precice Bone Transport nail must not come near an MRI scanner and must not undergo an MRI scan.
Other Information: •
•
• • • • • •
Upon removal from the package, compare the descriptions on the label with the package contents (product number and size) Packages for each of the components should be intact upon receipt. All implants should be carefully examined for completeness, and for lack of damage, prior to use. Damaged packages or products should not be used and should be returned to NuVasive Specialized Orthopedics. The Precice Bone Transport nail is provided sterilized by Gamma Irradiation Sterilization. Please refer to the package label for the expiration date of the Precice Bone Transport nail. The Precice Bone Transport nail is for single-use only. Do not sterilize the ERC. Do not attempt to re-sterilize the Precice Bone Transport Nail. Steam or Ethylene Oxide gas will not reach the internal components. Do not use if package is damaged or sterile barrier is broken.
LC0262-J 6/2022
12 | P a g e
Table 6: Symbols Definition:
Symbol
Definition Unsafe in Magnetic Resonance Imaging (MRI) Environments For Single Use Only, Do not re-use Do not use if package is damaged Do not Resterilize Non-Sterile Federal (US) law restricts the sale of this device for use by or on the order of a physician.
Rx Only/
Manufacturer Date of Manufacture
REF
Model Number
LOT
Lot Number
www.nuvasive.com/eifu
See Instructions For Use www.nuvasive.com/eifu Expiration Date Sterilized by Gamma Irradiation Authorized Swiss Representative
EC | REP
Authorized European Representative This product has met European Union health, safety, and environmental requirements, which ensure consumer and workplace safety.
Manufacturer: Nuvasive Specialized Orthopedics, Inc. 101 Enterprise, Suite 100 Aliso Viejo, CA, 92656 USA Tel. 1-855-435-5477 Email: [email protected]
EC | REP NuVasive Netherlands B.V. Jachthavenweg 109A 1081 KM Amsterdam The Netherlands Phone: +31 20 72 33 000
Australian Sponsor: Life Healthcare Pty Ltd. Level 8, 15 Talavera Road North Ryde NSW 2113 Australia UK Responsible Person: NuVasive UK Limited Suite B, Ground Floor, Caspian House The Waterfront, Elstree Herts United Kingdom
LC0262-J 6/2022
NuVasive Switzerland GmbH c/o Domenghini & Partners AG Falkengasse 3 6004 Luzern, Switzerland
13 | P a g e
This product, and the use thereof, may be covered by one or more of the following U.S. and/or international patents: US 7,955,357, US 7,981,025, US 8,057,472, US 8,197,490, US 8,382,756, US 8,419,734, US 8,449,543, US 8,715,159, US 8,734,488, US 8,808,163, CN 101917918, EP 2,114,258. Other U.S. and international patents pending. This product is licensed to the customer for single use only. Any resterilization or subsequent re-use is an unlicensed use and therefore constitutes patent infringement.
only
LC0262-J 6/2022
14 | P a g e