Quick Start Guide
4 Pages
Preview
Page 1
Scout Pro Balance
Quick Start Guide
Locked position
PREPARATION FOR USE
Subplatform
Pointer
Release Shipping Lock on top of the balance Turn the pointer 90° counter-clockwise. Install the Platform Rectangular platform: Place diagonally on subplatform and rotate counter-clockwise until it locks. Round platform: Set straight down on subplatform.
Connect Power
Adapter jack
Unlocked position
Draft Shield models: Position draft shield on top and rotate it until it faces forward.
Balances with leveling feet and bubble must be leveled before using. (Bubble is at rear, next to AC Adapter Input Jack.)
Ensure voltage identification label matches local line voltage. If not, do not connect the unit. Contact Ohaus or your dealer. Battery Installation Install the Four “AA” batteries with polarity as shown in the battery compartment.
SELECTING THE LOCATION: Place on a firm, steady surface with sufficient space.
Avoid excessive air current, vibrations, heat sources, or rapid temperature changes.
SAFETY PRECAUTIONS • • • • • • •
Before plugging in the balance, verify that local power supply matches voltage printed on power adapter. (Use only the adapter provided with the balance.) Disconnect the balance from the power supply when cleaning. Do not operate this product in hazardous or unstable environments. Do not drop loads on the pan. Use only approved accessories and peripherals, as available. Operate the product only under ambient conditions specified in the Instruction Manual. Service should be performed by authorized personnel only.
Ohaus Corporation www.ohaus.com
i
Scout Pro Balance Quick Start Guide
Scout Pro Balance
Quick Start Guide Symbols for weighing modes: G – Specific Gravity N – Newtons % – Percent PC – Pieces kg – Kilograms, g – grams dwt – (not used) lb:oz – (not used) ct – (not used) t – Totalize mode (or taels*) *Unit varies by model
CONTROLS Battery charge indicator
Stability indicator
Button ON/ZERO Off
PRINT Menu
Functions Short Press (when off) Short Press:(when on)
Turns scale on. If balance is on, sets display to zero.
Long Press
Turns scale off.
Extended Long Press
During power up, enters Menu mode.
Short press in Menu mode
Accept setting on display.
Short Press
Press and Hold
Sends print command to COM interface port. If Display Hold or Totalize mode is active, short press enters that mode. Scroll through Units. Release on desired unit.
Short press in Menu mode
“No” (toggles through available settings)
Locking the Menu The Lock Switch is used to lock out the menu mode, preventing unauthorized changes. To lock the menus, position the Lock Switch next to the tab on the bottom of the balance as shown.
Scout Pro Balance Quick Start Guide
Locked Unlocked
ii
Ohaus Corporation www.ohaus.com
Scout Pro Balance
Quick Start Guide OPERATION Weighing Start with the balance on. 1
(Rezero the display)
(Place sample on platform)
(Example 50g)
Taring a Container’s Weight Taring zeros the container weight. With balance on, place an empty container on the platform. (Container weight)
1
(Place material in container)
(50g sample)
(Container weight tared)
(Material and container removed)
To remove tare, press ON/ZERO Off again.
ADDITIONAL OPERATIONS Use the Units Menu to activate Parts Counting or Percent Weighing. (See back page.) To enable Display Hold, Totalize and Specific Gravity, use the Setup/Mode submenu. Parts Counting has two modes: (See Instruction Manual for more details.) Normal: balance determines quantity based on average weight of parts in original reference quantity. Enhanced: additional parts can be added to the platform ( ≤ the original number). The additional reference quantity produces a more accurate average part weight. Percent Weighing: place a reference weight on the balance, then view other loads as a percentage of the reference. The reference weight equals100%. Display-Hold mode captures and stores the highest stable value. When displayed, the stability indicator blinks. Note: Units cannot be changed when in Display-Hold mode. Totalize allows storage of a series of weight measurements. Totalize mode has been initiated when “t” and the current unit are displayed together. When totalized weight is shown, the “t” indicator blinks. Note: Units cannot be changed when in Totalize mode. The Specific Gravity mode allows calculating the specific gravity of a sample. (SPEC.GR mode must be turned ON before removing platform and installing hook.)
Ohaus Corporation www.ohaus.com
iii
Scout Pro Balance Quick Start Guide
Scout Pro Balance
Quick Start Guide
MENU NAVIGATION There are four main menus in the balance: .C.A.L., .S.E.T.U.P., .U.N.I.T.S. and .E.N.D. (Start with the balance off and the Lock Switch off: see page ii). The sequence is shown below. 5
(Release button)
1
(Acquiring zero value)
1
1
1
(Weigh Mode)
MENU STRUCTURE Accepting/Bypassing Menu Items Start with menu item displayed.
Cal − Yes/No
Setup − Auto-Off -On/Off − Lin Cal -Yes/No
1
− Mode -Hold -Totalize -Specific Gravity Off − End
= YES Accept
1
-Yes/No
= NO
1
(Short presses advance through menu)
*80253128*
Units −g -On/Off − kg -On/Off − oz -On/Off − lb -On/Off − PC -Count -Cnt.Enh Off −% -On/Off − End
End − Yes/No
-Yes/No
P/N 80252993
Scout Pro Balance Quick Start Guide
iv
Ohaus Corporation www.ohaus.com