RADIOMETER

ABL700 Series Reference Manual Edition Q

Reference Manual

234 Pages

File Type: PDF

File Size: 5.46 MB

File Name: RADIOMETER - ABL700 Series Reference Manual Edition Q.pdf

Preview

Page 1

ABL700 series reference manual

Note to the users of the EML105, ABL5xx, ABL SYSTEM 6xx, ABL7xx Series, ABL800 FLEX and ABL800 BASIC analyzers Introduction

This note to users outlines a change in the operator’s and reference manual for your EML105, ABL5xx, ABL SYSTEM 6xx, ABL7xx Series, and/or ABL800 FLEX and ABL800 BASIC analyzer.

Brief overview of the change

Operator’s manual: Limitations of use and known interfering substances: CAUTION - Known interfering substances Substance

Interference

–

For ClO4 , interference on cCa2+ (1.25 mmol/L level) has been detected:

ClO4 (drugs)

cCa2+ (1.25 mmol/L level): 0.20*. * Depending on the pH level

Reference manual: Change/Description Interference on

–

For ClO4 , interference on cCa2+ (1.25 mmol/L level) has been detected. The interference results for ClO4– are as follows: Interference on…

Substance

ClO4–

Test Conc.

1.5 mmol/L

cK+

cNa+

cCa2+

cCl

(4 mmol/L level)

(150 mmol/L level)

(1.25 mmol/L level)

(110 mmol/L level)

0.20*

8-30

* Depending on the pH level A "-" indicates that interference has not been measured on the respective parameter.

Technical documentation

The manual will be updated with the above information as part of the next manual update.

Instructions to user

Please place this note to the users in the binder of your manual.

Note to users of the ABL700 Series analyzers Mandatory upgrade of the manual

The manuals for the ABL700 Series analyzers must be upgraded with regard to the information on cleaning solution. The procedure for adding cleaning additive has been changed for the abovementioned analyzers and from now on the following instructions must be followed:

Cleaning solution with cleaning additive installation

Remove the foil from the DosiCapZip and unscrew it (Figs. 1+2).

Turn the DosiCapZip upside down and screw it onto the container again (Figs. 3+4). CAUTION: If the contents of the DosiCapZip or the container have been spilt by accident, both the container and the DosiCapZip should be discarded to prevent incorrect concentrations in the solution. T

Invert the container at least 20 times to dissolve the additive (Fig. 5).

Place the container horizontally so that the solution may enter the DosiCapZip and leave it for 3 minutes (Fig. 6).

Invert the container again at least 20 times to fully dissolve the additive (Fig. 7).

Unscrew the lid from the new solution container.

Remove the used solution container by holding it on the sides and pulling.

Scan the barcode of the new solution, using the barcode reader.

Place the new solution container in position on the analyzer and push it firmly onto the connector as far as possible.

10.

For the ABL700 Series analyzers, sw. 3.836: Press Restart to restart the analyzer. For the ABL700 Series analyzers, sw. 6.00: Press Restart and Accept to restart the analyzer.

Cleaning solution with cleaning additive – general information

Item Cleaning Solution 175 mL

Code No. 944-123

Type S7375

Use: For cleaning the measuring system of the ABL700 Series analyzers. Contains: Salts, buffer, anticoagulant, preservatives, surfactants and enzyme. Safety Data Sheet may be obtained from your local distributor. Storage: At 2-10 °C. Stability in use: The Cleaning Solution with the Cleaning Additive is stable for 2 months in use. Analyzer: Perform cleaning every 8th hour. CAUTION – Risk of personal injury Do not breathe dust (S22). Avoid contact with skin (S24). Irritating to eyes and skin (R36/38). Wear suitable gloves (S37). May cause sensitization by inhalation and skin contact (R42/43). In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) (S45). T

Texts no longer valid in the manuals

Due to new cleaning solutions, information about Cleaning solution S7370 and Cleaning additive S5370 is no longer valid. Below is a list of the sections in the manual that must be ignored.

ABL700 Series reference manual: Chapter 7: Solutions and gas mixtures: S7370 Cleaning Solution and S5370 Cleaning additive:

Text no longer relevant. See instruction about the new Cleaning Solution S7375 above instead.

Index:

Cleaning Additive references no longer relevant.

Technical documentation

The manuals for the ABL700 Series analyzers will be updated with the above information when reprinted.

Instructions to user

This update kit includes a note to the user with the changes and a new date of issue page of the manual. Please place the note to the user in the binder of the ABL700 Series reference manual and replace the date of issue page with the new corresponding page, then discard the old page.

Contents

ABL700 Series

Reference Manual

Introduction

Electrodes

The Optical System

User-defined Corrections

Performance Characteristics

Parameters

Solutions

Interfacing Facilities

Index

Date of Issue

SYSTEM PERFORMANCE AND WARRANTY DISCLAIM Radiometer cannot provide or verify instrument performance characteristics and accept warranty claims or product liability claims if the recommended procedures are not carried out, if accessories other than those recommended by Radiometer are used, or if instrument repairs are not carried out by authorized service representatives. The instructions given in the Operator’s Manual for the ABL700 Series must be observed in order to ensure proper instrument performance, and to avoid electrical hazards.

TRADEMARKS ABL™, BMS™, FLM™, CMT™, Deep Picture™, QUALICHECK™ and RADIOMETER™ are trademarks of Radiometer Medical ApS, Denmark. ABL is registered in the USA. QUALICHECK is registered in the USA and in some other countries.

COPYRIGHT The contents of this document may not be reproduced in any form or communicated to any third party without the prior written consent of Radiometer Medical ApS. While every effort is made to ensure the correctness of the information provided in this document Radiometer Medical ApS assumes no responsibility for errors or omissions which nevertheless may occur. This document is subjected to change without notice. ©Radiometer Medical ApS, DK-2700 Brønshøj, Denmark, 2006. All Rights Reserved.

ABL700 Series Reference Manual

Contents

Contents 1.

Introduction ... 1-1 ABL700 Series Documentation ... 1-2 Warnings/Cautions and Notes ... 1-3

Electrodes ... 2-1 General Construction ... 2-2 General Measuring Principles... 2-3 Calibration ... 2-7 Electrode Measuring Time and Updatings ... 2-14 Reference Electrode ... 2-15 pH Electrode ... 2-16 pCO2 Electrode ... 2-23 pO2 Electrode... 2-32 Electrolyte Electrodes ... 2-42 Metabolite Electrodes ... 2-54 References... 2-64

The Optical System ... 3-1 Measuring Principle... 3-2 Correcting for Interferences... 3-7 Calibration ... 3-9 Measurement and Corrections ... 3-10 References... 3-13

User-Defined Corrections ... 4-1 General Information... 4-2 Correction Factors for Oximetry Parameters and Bilirubin... 4-4 Electrolyte and Metabolite Parameters ... 4-8

Performance Characteristics... 5-1 General Information... 5-2 Definition of Terms and Test Conditions ... 5-3 Reference Methods for the ABL700 Series ... 5-8 ABL735/30/25/20/15/10/05 Performance Test Results - Macromodes... 5-10 ABL735/30/25/20/15/10/05 Performance Test Results - Micromodes ... 5-19 ABL700 Performance Test Results ... 5-30 ABL735/30/25/20/15/10/05/00 Expired Air Mode ... 5-32 ABL735/30/25/20/15/10/05/00 Capillary - pH Only Mode ... 5-35

Contents

ABL700 Series Reference Manual

ABL735/30 Performance Test Results - Bilirubin... 5-36 Interference Tests... 5-42 References... 5-50 6.

Parameters ... 6-1 General Information... 6-2 Acid-base Parameters... 6-6 Oximetry Parameters ... 6-8 Oxygen Parameters ... 6-9 Bilirubin ... 6-13 Electrolyte Parameters ... 6-14 Metabolite Parameters ... 6-15 Units and Ranges for Measured Parameters ... 6-16 Units and Ranges for Input Parameters ... 6-19 Units and Ranges for Derived Parameters ... 6-20 List of Equations... 6-25 Oxyhemoglobin Dissociation Curve (ODC)... 6-41 Conversion of Units ... 6-46 Default Values ... 6-48 Altitude Correction ... 6-49 References... 6-50

Solutions and Gas Mixtures ... 7-1 General Information... 7-2 S1720 and S1730 Calibration Solutions ... 7-3 S4970 Rinse Solution ... 7-4 S7370 Cleaning Solution and S5370 Cleaning Additive... 7-5 S7770 tHb Calibration Solution... 7-6 Gas Mixtures (Gas 1 and Gas 2) ... 7-7 Electrolyte Solutions... 7-8 S5362 Hypochlorite Solution ... 7-9 Certificates of Traceability ... 7-10

Interfacing Facilities ... 8-1 Connecting a Mouse ... 8-2 Connecting an Alphanumeric Keyboard... 8-3 Connecting the Bar Code Reader... 8-4 Connecting a Network ... 8-6

Index Date of Issue

ABL700 Series Reference Manual

1. Introduction

1. Introduction Overview

This section gives an introduction to the documentation that accompanies your ABL700 Series analyzer. It describes how this particular manual is organized and explains the different notices that appear in it.

Contents

This chapter contains the following topics. ABL700 Series Documentation ...

1-2

Warnings/Cautions and Notes...

1-3

1-1

1. Introduction

ABL700 Series Reference Manual

ABL700 Series Documentation ABL700 Series Analyzers

The documentation that accompanies the ABL700 Series analyzers covers the series in general - each possible electrode combination is not considered individually.

Documentation

The table below describes the documentation that comes with each analyzer. Documentation The Operator’s Manual

Description Contains all the information required for everyday operation of the analyzer. Describes the functions of the analyzer and how to set it up according to customer needs and requirements. Explains error messages and gives troubleshooting procedures. Contains ordering information

The Reference Manual

Gives detailed information about the operating principles of the analyzer. Describes the measuring and calibrating principles. Lists all the parameters. Gives the equations from which the derived parameters are calculated. Gives information about how the performance of the analyzer is tested.

On-line Help

Summarizes the information found in the Operator’s Manual. Gives hands-on help at the analyzer.

Design of Manual

1-2

Depending on the set up of your analyzer, the entire Reference Manual may not be applicable to it. However the manual is designed in such a way that it is easy to disregard or remove the sections that are not relevant to your instrument.

ABL700 Series Reference Manual

1. Introduction

Warnings/Cautions and Notes Definitions

The following table indicates the type of information given in warnings, cautions, and notes: Notice WARNING

PRECAUTION

NOTE List of WARNING/ CAUTION Notices

Definition Warnings alert users to potentially serious outcomes to themselves or to the patient (such as death, injury, or serious adverse events). Precautions alert users to exercise the special care necessary for safe and effective use of the device. They may include actions to be taken to avoid effects situations on patients or users that may not be potentially life threatening or result in serious injury , but about which the user should be aware. Precautions may also alert the user to adverse effects on the device caused by use or misuse, and the care required to avoid such effects. Notes give practical information.

All WARNING/CAUTION notices that appear in this manual, are listed below. • S5370 Cleaning Additive: May cause sensitization by inhalation and skin contact). Do not breathe dust. Avoid contact with skin. Wear suitable gloves. In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible). • Gas Mixtures: Not for drug use. High pressure gas. Do not puncture. Do not store near heat or open flame - exposure to temperatures above 52 oC (125 oF) may cause contents to vent or cause bursting. Not for inhalation. Avoid breathing gas - mixtures containing carbon dioxide can increase respiration and heart rate. Gas mixtures containing less than 19.5 % oxygen can cause rapid suffocation. Store with adequate ventilation. Avoid contact with oil and grease. Only use with equipment rated for cylinder pressure. Use in accordance with Safety Data Sheet.

1-3

2. Electrodes Introduction

This chapter describes the construction, measuring principle and calibration process for each of the electrodes in the ABL700 Series analyzers. General sections covering the background theory used for measurements and calibrations are also presented here.

Contents

This chapter contains the following topics. General Construction ...

2-2

General Measuring Principles ...

2-3

Calibration... 2-7 Electrode Measuring Time and Updatings... 2-14 Reference Electrode ... 2-15 pH Electrode ... 2-16 pCO2 Electrode... 2-24 pO2 Electrode ... 2-33 Electrolyte Electrodes ... 2-43 Metabolite Electrodes... 2-55 References ... 2-65

2. Electrodes

ABL700 Series Reference Manual

General Construction An Electrode

In this manual and other Radiometer literature, the term electrode refers to the whole sensor unit, i.e. both the electrode and the electrode jacket. Radiometer electrodes are cordless, thereby limiting the level of noise picked up during the measuring process. The electrical signals from the electrodes are amplified by preamplifiers placed in each module. A generalized diagram of a Radiometer electrode is given below. Electrical contact

Color-coded ring

Electrolyte solution

Electrode jacket

Membrane

The main electrode parts are described below. Part

Description

Electrical contact

Provides electrical contact between the electrode and the analyzer.

Color-coded ring

Marks each electrode for easy recognition.

Electrode jacket

Holds the electrolyte solution and membrane, and protects the electrode.

Membrane

A thin sheet-like material to separate the sample from the electrode, that differentiates between the substances allowed to pass through it towards the electrode.

Electrolyte solution

A conducting solution to provide an electric contact between the electrode and the sample (also known as a salt-bridge solution).

More specific descriptions of the electrodes are found under the appropriate electrode titles in this chapter.

2-2

ABL700 Series Reference Manual

2. Electrodes

General Measuring Principles Introduction

There are two different measuring principles employed for electrodes in the ABL700 Series. • Potentiometry: The potential of an electrode chain is recorded using a voltmeter, and related to the concentration of the sample (the Nernst equation). • Amperometry: The magnitude of an electrical current flowing through an electrode chain, which is in turn proportional to the concentration of the substance being oxidized or reduced at an electrode in the chain. These two measuring principles are described in detail on the following pages.

Potentiometric Method

An electrode chain describes an electrical circuit consisting of a sample, electrode, reference electrode, voltmeter, membranes, and electrolyte solutions. Voltmeter

Reference electrode

Electrolyte solution

Sample

Membrane

Electrolyte solution

Electrode

Membrane

Every element in the electrode chain contributes a voltage to the total potential drop through the chain. Thus: • When immersed in the appropriate electrolyte solution, both electrodes have separate potentials. • The membrane junctions between the sample and electrolyte solutions also have separate potentials. The complete electrode chain potential therefore, is the sum of these separate potentials and is the quantity measured by the voltmeter. Etotal = Esample – ERef where the final unknown potential (Esample) can be calculated knowing the total electrode chain potential (Etotal) and the reference potential (ERef that is constant between two subsequent calibrations). Continued on next page

2-3

2. Electrodes

ABL700 Series Reference Manual

General Measuring Principles, Continued Potentiometric Method (continued)

Having measured the unknown potential (Esample), the Nernst equation is then applied to determine the activity (ax) of the species under study: 2.3RT log a x E sample = E 0 + nF where:

standard electrode potential

R = = T = n F =

gas constant (8.3143 JK−1mol−1) absolute temperature (310 K (37 oC )) charge on the ion Faraday constant (96487 C mol−1)

activity of x

The Nernst equation is rearranged to express the activity as a function of the potential Esample. Having measured Esample the activity can be calculated since all other quantities are already known. Finally the analyzer converts activity to concentration. Strictly speaking, in potentiometry the potential of an electrode chain or the magnitude of current flowing through an electrical chain is related to the activity of a substance, and not its concentration. Activity expresses the ‘effective concentration’ of a species, taking non-ideality of the medium into account. Activity and concentration are related by the following equation: ax = γ cx

where: ax = the activity of the species x γ

= the activity coefficient of species x under the measurement conditions (for ideal systems γ = 1)

= the concentration of species x (mmol/L)

NOTE: To be exact, activity is related to the molality of species x, i.e., the number of mmoles per kg of solvent. However molality is converted to concentration (molarity).

ABL700 Series analyzers automatically convert activities into concentrations [1]. The term concentration is therefore used in explanations of the measuring principles for each of the electrodes further on in this chapter. The potentiometric measuring principle is applied in the pH, pCO2, and electrolyte electrodes. It is slightly different for the pCO2 electrode, however, since the Nernst equation is not directly applied. Continued on next page

2-4

ABL700 Series Reference Manual

2. Electrodes

General Measuring Principles, Continued The electrode chain in amperometric measurements consists of the sample, the two electrodes (anode and cathode), an amperemeter, a voltage source, the membranes, and the electrolyte solutions.

Amperometric Method

Amperemeter Applied voltage

Anode

Cathode

Electrolyte solution Membrane Sample

Part

Function

Cathode

Negative electrode where a reduction reaction occurs and electrons are consumed.

Anode

Positive electrode where an oxidation reaction occurs and electrons are released.

Electrolyte solution

Provides electrical contact between the anode and cathode.

Membrane

Allows the appropriate molecules to pass through from the sample.

Sample

Contacts the membrane.

Applied voltage

Applies the necessary potential for the reduction or oxidation reaction under study.

Amperemeter

Measures the current flowing through the circuit.

To simplify the description of the measuring process in an amperometric electrode, we make the following assumptions: •

there is a species A in the sample which is reduced at the cathode to A−.

•

there is a species X in the electrolyte which is oxidized at the anode to X+.

Continued on next page

2-5

2. Electrodes

ABL700 Series Reference Manual

General Measuring Principles, Continued Amperometric Method (continued)

The membrane is selective to the species A, allowing no other species but it to pass through from the sample into the electrolyte solution. As an appropriate potential is applied across the electrodes, the species A is reduced at the cathode according to the following reaction: A + e− → A− The reduction of A produces a flow of electrons, i.e. an electrical current. To complete the electrical circuit an oxidation reaction where electrons are released is necessary. Therefore species X is oxidized according to the following reaction: X → X+ + e− The magnitude of the current flowing through the circuit is proportional to the concentration of the species being reduced, in this case species A. The analyzer thereby automatically calculates the concentration of A in the sample. The amperometric measuring principle is applied in the pO2, glucose, and lactate electrodes.

2-6

ABL700 Series Reference Manual

2. Electrodes

Calibration Actual Electrode The electrodes are active elements and must be calibrated regularly as the signals from the electrodes change with, e.g. age or deposits on the membrane. Condition

Calibration relates the electrode signals during the calibration sequence to the values of the calibrating solutions and must be performed at regular intervals so that the accuracy can be constantly refined after inevitable minor changes in the electrodes’ behavior. Actual electrode condition is described by status/zero point and sensitivity and compared with theoretical conditions for an "ideal" electrode. In addition to status and sensitivity, an electrode condition is described by drift. Calibration Line The calibration line expresses the relationship between the potential (or current) measured at an electrode, and the concentration of the species specific to the electrode. The calibration line forms the basis of the scale used by the analyzer to convert electrode chain potentials to concentrations. Each electrode has a different calibration line.

The pH electrode is used as an example to illustrate how this line is derived from two calibration solutions of known pH. • Cal 1 solution has a pH of 7.398 that gives potential reading of −100 mV. • Cal 2 solution has a pH of 6.802 that gives a potential reading of −64 mV.

These two values are plotted on a graph. The relationship between potential and pH is linear so a line can be drawn between the two points, as shown below: Measured potential (mV) −64

Calibration line

−97 −100

6.802

7.346 7.398

pH of Cal 2 sol.

pH of sample pH of Cal 1 sol.

The calibration line now forms the scale used to convert the potential measured at the pH electrode during sample analysis to an actual pH value. Continued on next page

2-7

2. Electrodes

ABL700 Series Reference Manual

Calibration, Continued Calibration Line A blood sample gives a potential reading of -97 mV at the pH electrode. Reading off from the calibration line shown below, this potential corresponds to a pH of (continued) 7.346. Measured potential (mV) −64

Calibration line

−97 −100

6.802

7.346 7.398

pH of Cal 2 sol.

pH of sample pH of Cal 1 sol.

The calibration line is updated at every calibration. Drift describes the variation in the calibration line between consecutive calibrations. The theoretical calibration line is the relationship between potential and Theoretical Calibration Line concentration in a potentiometric measurement, or the relationship between current and concentration in an amperemetric measurement. In the ABL700 Series the theoretical calibration line for pH is defined by the following two points: pH

Electrode potential (vs. Ref. potential)

6.800

−75.5 mV

7.400

−112.4 mV

Measured potential (mV)

−75.5

−112.4

6.8

7.4

The position and slope of the calibration line compared to the theoretical calibration line are described by the status and sensitivity respectively. Continued on next page

2-8

Previous Page Next Page