T652M and MD Instruction Manual Oct 2011

TABLE OF CONTENTS 1. INTRODUCTION...

1

2. IMPORTANT SAFETY PRECAUTIONS... 2 3. LIST OF PARTS... 7 4. TREADMILL ASSEMBLY... 10 STEP 1 Assemble the Left and Right Pedestals and Handlebars... 10 STEP 2 Install the Display... 17 STEP 3 Install Long Handrails... 20 STEP 4 How to Move the Treadmill... 26 STEP 5 Level the Unit... 27 STEP 6 Align the Walk Belt... 28 STEP 7 Adjust Walk Belt Tightness... 29 STEP 8 Install the Power Cord... 30 STEP 9 Replacing the Fuse... 31 5. T652M DISPLAY... 32 Display Features... 32 Display Functions... 32 Button Functions... 33 Safety Key... 35 Workout Time Limit Setting... 35 6. HOW TO USE YOUR T652M TREADMILL... 36 Quick Start... 36 Workout Setup... 36 Operating Procedure during Exercise... 37 Cool Down... 38 7. ABOUT THE HEART RATE DETECTION AND PRESENTATION... 39 About Telemetry Heart Rate... 39 About Contact Heart Rate... 39 8. PROGRAM DETAILS... 41 9. GUIDELINES FOR EXERCISE... 44 10. USER PARAMETER SETTING... 45 USB PORT... 45 11. MAINTENANCE... 46 12. MAINTENANCE CHECKLIST... 50 13. ERROR MESSAGES... 53 14. WIRING SCHEMATIC... 54

SPORTSART T652M COMMERCIAL TREADMILL INTRODUCTION Congratulations on the purchase of one of the finest pieces of commercial exercise equipment on the market today, the SportsArt T652M Commercial Treadmill. The T652M is designed with the end-user in mind and constructed of high quality materials for years of trouble-free use. Before using your SportsArt T652M Treadmill, we recommend that you familiarize yourself with this Owner's Manual. Whether this is the first time you have operated a treadmill, understanding the correct use of the equipment will enhance your ability to achieve your exercise goals safely and successfully.

1

LIST OF PARTS

Assembly Parts Number Name A1 Display Handlebar assembly A2 Safety key Right pedestal A3 Feeder cord A4 Waterproof ring A5 Main frame A6 Right side cover A6a Left side cover A6b Left pedestal A7

Qty 1 1 1 1 1 2 1 1 1 1

Qty Name Number 1 A8 Owner manual 1 A9 Hardware kit 1 A10 Power cord 1 Applicator tube A11 4 Silicone lubricant Upper and lower left and 1 A12 right connector covers A13 Left and right long handrails 1 A14

7

Left and right long handrail supports

1

Hardware Kit Name

Qty

31

Screw cover (flat)

2

32

Screw cover (rounded)

2

Number

Specification

1

15A-100V~110V

1

10A-200V-240V

L-shaped Allen wrench

1

(M4)

L-shaped Allen wrench

1

(M5)

L-shaped Allen wrench

1

(M6)

L-shaped Allen wrench

1

(M6)

Double open-end wrench

1

(22*24)

Screwdriver handle

1

green

Screwdriver bit

1

Phillips and flat

Fuse

Notes

Components on the Product Number 41

Name

Specification

Inner hex screw

M8* L18

Spring washer

M8 ψ18* ψ 8.5* t2

Star washer Mushroom top inner hex screw Serrated washer (curved)

M8* L20 ψ18* ψ 8.5* t2

Mushroom top inner hex screw

M8* L20

Serrated washer

ψ18* ψ 8.5* t2

44

Mushroom top inner hex screw

M5* L12

45

Phillips head screw

M4* L8

42 43

8

Notes

Please make sure that the walk belt runs below the walk belt guides. Walk belt guides should press the walk belt down on both sides. If the walk belt is on top of the guides, loosen screws at position A. Place the walk belt below the guides as shown. Then readjust walk belt tightness per instructions in part 6.

9

TREADMILL ASSEMBLY STEP 1

Assemble the Left and Right Pedestals and Handlebars

10

1-1. Remove pedestal mount covers (A6a,A6b). 1-2. Remove screws (41) from the pedestal mount as shown.

11

1-3. Follow steps (a~e) in order to thread the data cable into the right pedestal. (a) First, remove the zip tie on the cable in the right pedestal mount. Then stretch the cable out as shown. (b) Place the right pedestal (A3) on the floor, with the lower hole facing the data cable. Disconnect the feeder cord (A7) from the bottom of the pedestal. Wrap this feeder cord around the top of the data cable to secure them together. (c) Disconnect the feeder cord (A7) at the top of the right pedestal (A3). (d) Pull the feeder cord (A7) to thread the data cable through the right pedestal (A3). (e) Once the data cable has been threaded through the pedestal, disconnect the feeder cord (A7) from the data cable.

12

1-4. Hold the data cable at the top of the right pedestal (A3), and insert the bottom of the pedestal onto the pedestal mount. Avoid pinching or crimping the data cable. Place the water guard (A6) on the pedestal higher than the motor cover. Loosely secure the right pedestal (A3) with screws (42). Insert the left pedestal (A5) onto its pedestal mount, and loosely secure it with screws (42). Do not tighten screws. Make sure the pedestals can still move slightly.

13

1-5. Follow steps (a~e) to install handlebars. a. First, remove the screws (42, 43) from the handlebar assembly (A2). b. Insert the left side of the handlebar (A2) into the left pedestal (A7). c. Connect the cables in area A from the right pedestal (A3) and from the handlebar (A2).

14

d. Tuck cables into the pedestal safely. Then insert the right side of the handlebar assembly (A2) into the right pedestal (A3), without pinching or crimping cables. e. Thread screws in place by hand. First, secure screws (42) in area B. Then secure screws (43) in area C. f. Insert the screw cap (31) onto the screw head.

15

1-6. After the handlebars are in place, secure pedestal screws on left and right sides. Put pedestal covers (A6a,A6b) in place. Then put water guards (A5) down against the motor cover on both sides.

16

STEP 2

Install the Display

17

2-1. Follow steps (a~g) below to install the display assembly. a. Remove screws (44) from the handlebar (A2). b. Insert the display (A1) onto the handlebar assembly (A2). Note: aim properly to avoid damaging the display board. c. Then slightly lift the display (A1). d. Temporarily secure the display by inserting it as indicated by arrows.

18

e. Connect cables in areas A and B. f. After connecting cables, tuck them away for safety. Then slightly lift the display (A1) and press it into place. Note: In area C, the display cover must be outside of the handlebar cover. g. Use screws (44) to secure the display (A1) in place.

19

3-1. First, remove the sticker, screws, and end cap from the left and right handlebars. Also, remove the two middle anti-slip strips from the landing strips.

21

3-2. First, detach upper and lower connector covers from the left and right handrails. Then remove the screws from the lower part of the handrails.

22

3-3. First, set the long handrail supports into the frame. Then loosely secure them with screws. Do not tighten the screws yet.

23

3-4. Set left and right long handrails in place on the handrail supports as shown. Use screws (a,b) to secure the long handrails to the handle ends.

24