ResMed
VS III Quick Setup Guide
Quick Setup Guide
2 Pages
Preview
Page 1
70825 VS III Quick Setup Guide, ROW Eng.indd 1
sensor connector
Oxygen %
connector
Mains
connector
connector
External battery Serial link
29/9/08 3:55:27 PM
alarm connector
Remote
28 V
Oxygen port connector
Rear panel Enter key • Start ventilation • Enter and confirm your selection
On/Off key • Switch the ventilator on/off • Stop ventilation VS III
Adjustment keys • Navigate through menus • Increase or decrease values
English
Menu key • Navigate through the menu and return to the previous page • Press and hold: access the clinical menu and return to the patient menu
VS III™
Keypad and navigation
Quick Setup Guide
Alarm Silence key • Silence the current alarm • Clear the alarm message
Starting/stopping ventilation When the battery is discharging, the battery graphic shows an arrow pointing downwards with an indicative level status.
Starting From the Clinical Settings menu, select Start ventilation then press . From the Patient menu, follow the onscreen instructions then press
.
Stopping
1
then press
2
3
4
5
6
7
8
Note: When you begin charging, there is a two-minute delay before the battery starts charging.
From the Clinical Settings menu, select Stop ventilation then press . Alternatively press and again for one second. From the Patient menu, press one second.
Carry bag
again for
Operating the battery Internal battery When the battery is charging, the small battery graphic shows an arrow pointing upwards. The arrow disappears once the battery is fully charged. The device comes with a bag that is easy to carry and hang on a wheelchair for maximum mobility. The detachable accessories pouch allows the accessories to be carried separately if required. Saime SAS (Manufacturer), Z.I., 25 rue de l’Etain, 77176 Savigny-le-Temple, France. ResMed Schweiz AG Viaduktstrasse Basel, Switzerland, +41 61 564 7000, ResMed Corp Poway, CA, USA +1 858 746 2400, ResMed Ltd Bella Vista, NSW, Australia, +61 (2) 8884 1000. ResMed has offices in Australia, Austria, Brazil, China, Finland, France, Germany, Hong Kong, India, Japan, Malaysia, the Netherlands, New Zealand, Norway, Singapore, Spain, Sweden, Switzerland, the United Kingdom and the United States (see www.resmed.com for details). Protected by the following patent: FR 2839893. Other patents pending. VS III is a trademark of Saime SAS. Specifications may change without notice. © 2008 Saime SAS is a subsidiary of ResMed Inc.70825/1 08 09.
Global leaders in sleep and respiratory medicine
www.resmed.com
70825 VS III Quick Setup Guide, ROW Eng.indd 2
29/9/08 3:55:37 PM
Setting up the ventilator Connecting the power cord Double circuit connections
3 %
28 V
1
Double circuit support connection 2
Double circuit connection
Connecting the circuits
Turning the ventilator on/off
Single circuit connections
To turn the ventilator on, press
and wait until the end of the
auto-test.
To turn the ventilator off, press
, select Turn off ventilator and to confirm or follow the onscreen instructions.
press
Accessing the clinical menu P
P
Single leak circuit with proximal pressure line and vented mask connection
1. P ress
for three seconds until the confirmation screen appears.
2. Select the desired duration and
Single circuit with proximal pressure line and non-vented mask connection
confirm.
To return to the Patient menu, press
for one second.
CLINICAL MENU FOR MEDICAL STAFF Setting a ventilation program While ventilating or in standby mode, you can select modes, set parameters and set alarms.
Clinical Settings menu screen while ventilating
Setting alarms
Clinical Settings menu screen in standby mode
Selecting a ventilation mode
Press
2.
Press and desired mode.
1.
Press to confirm the changes and go to the next alarm.
5.
Press value.
4.
Press
3.
Press and alarm to modify.
2.
From the Clinical Settings menu, select Alarms then press .
1.
to select the
to select the
to edit the alarm. and
to modify the
CAUTION Parameters and alarms are saved in the device as soon as they are edited.
to confirm.
Setting parameters
Specific actions in standby mode
ress P to confirm the changes and go to the next parameter.
5.
Press value.
4.
P ress
3.
ress P and to select the parameter to modify.
2.
F rom the Clinical Settings menu, select Parameters then press .
1.
When in standby mode, you can: • set a new circuit configuration • set up a new patient (all trends and values are reset) • select options (1 or 2 programs, I:E or Ti).
to edit the parameter. and
From the Main Menu, press select the appropriate item.
to modify the
to