ELECTRIC PEN DRIVE SYSTEM Reference Guide Sept 2014

indications The Electric Pen drive is indicated for screw insertion, pin and wire placement, cutting of bone and metal, drilling, reaming, decorticating, shaping, and smoothing of bones and teeth in a wide variety of surgical procedures, including but not limited to general orthopaedic trauma, foot, hand, maxillofacial, neurosurgical, oral, otolaryngological, reconstructive, and spine surgery. Caution: Please review the Electric Pen Drive User’s Manual prior to use for indications and other important information.

Electric Pen Drive System

Reference Guide

DePuy Synthes Power Tools   1

Console Slide control For adjusting maximum speed for Drive Unit 2

Selection switch For torque limiting

Slide control For adjusting maximum speed for Drive Unit 1

Selection switch For irrigation

ON/OFF LED

Connector For Light Adaptor for Small Battery Drive/ Small Battery Drive II

Flow rate adjustment knob For irrigation

Connector For Drive Unit 1

Irrigation pump

Connector For Drive Unit 2

Connector For Foot Switch

*Wipe clean only with a cloth moistened with disinfectant. Do not immerse, rinse or sterilize.

2   DePuy Synthes Power Tools Electric Pen Drive System

Reference Guide

consolE sEtUP • confirm that the power switch is in the oFF (o) position. • connect the console to a power outlet using the supplied electrical cord.

• turn on the console by setting the power switch to the on (I) position.

• the lEd marked ( ) on the front of the console will illuminate, indicating that the console is under power.

• to connect the cable for the drive Unit, align the red dot on the metal plug with the red dot on the connector and push the plug into the connector. • to remove the cable, retract the release sleeve on the plug and pull back. • do not pull on the cord to disconnect, as this may damage the cable or console.

Electric Pen Drive System Reference Guide DePuy Synthes Power Tools

3

driVE Unit sEtUP • always slide the lock in the direction of the arrows before turning the mode switch. the lock will automatically return to the locked position. • to insert the black plug into the drive Unit, ensure that the mode switch on the drive Unit is in the cable insertion/ removal ( ) position. align the groove on the plug with the notch in the mode switch and insert the plug. cable insertion/removal

• once the cable connector is inserted, turn the mode switch to the lock ( ) position. the cable is now firmly locked into the drive Unit and the drive Unit is in the off mode. • to remove the cable, return the switch to the cable insertion/removal position ( ) and pull gently on the plug. do not pull on the cable, as this may damage the drive Unit or plug. lock (drive Unit oFF)

4

DePuy Synthes Power Tools

Electric Pen Drive System Reference Guide

driVE Unit sEtUP (continued) • to attach the hand switch to the drive Unit, align the arrows on the sides of the hand switch with the positioning arrows on the drive Unit. Press down on the hand switch until it clicks into place on the drive Unit.

• the drive Unit can now be operated by using the hand switch. the blue switch on the hand switch can also be used to lock the drive Unit.

locking switch

Electric Pen Drive System Reference Guide DePuy Synthes Power Tools

5

driVE Unit oPEration the mode switch located on the base of the drive Unit is used to lock or change rotational direction of the drive Unit. the switch is also used during the insertion and removal of the drive Unit cable. always slide the lock before turning the mode switch. For insertion or removal of the cable. drive Unit will not function in this position.

locking mechanism for mode switch

locked position prevents accidental operation of the drive Unit clockwise rotation cable insertion/removal

lock (drive Unit oFF)

counterclockwise rotation

Forward (clockwise) 6

DePuy Synthes Power Tools

Electric Pen Drive System Reference Guide

reverse (counterclockwise)

attachmEnt insErtion Important: To prevent injuries, the mode switch on the Drive Unit or the On/Lock switch on the Hand Switch should be in the Lock position when inserting or removing attachments or instruments.

• turn the release ring clockwise until it locks in the open position. the release ring will protrude slightly from the main body of the drive Unit.

• insert the attachment into the coupling, aligning the position pins of the attachment with the grooves on the release ring. • Press the attachment lightly against the drive Unit. the release ring will lock automatically. • Pull lightly on the attachment to confirm that it is secure.

Electric Pen Drive System Reference Guide DePuy Synthes Power Tools

7

attachmEnt rEmoVal While holding the drive Unit with the attachment facing up, turn the release ring clockwise until it locks in the open position.

remove the attachment. the release ring should stay in the open position, ready for the next attachment.

8

DePuy Synthes Power Tools

Electric Pen Drive System Reference Guide

drilling sPEEd attachmEnts Inserting an instrument Instruments 05.001.030

drill attachment, mini quick coupling

05.001.031

drill attachment, J-latch coupling

05.001.032

drill attachment, ao coupling

05.001.033

45° oscillating drill attachment, mini quick coupling

05.001.042

45° drill attachment, mini quick coupling

05.001.043

45° drill attachment, J-latch coupling

05.001.044

45° drill attachment, ao coupling

05.001.110

drill attachment, hex coupling

Pull back the collar of the attachment and insert the instrument, turning it slightly to align the keyway. release the collar of the attachment and pull lightly on the instrument to confirm that it is secure. Electric Pen Drive System Reference Guide DePuy Synthes Power Tools

9

drilling sPEEd attachmEnts (continued) Inserting an instrument in 90° Drill Attachment Instruments 05.001.035

90° drill attachment, short, mini quick coupling

05.001.036

90° drill attachment, long, mini quick coupling

move the locking lever of the attachment to the side as indicated by the arrow on the attachment.

10

DePuy Synthes Power Tools

Electric Pen Drive System Reference Guide

drilling sPEEd attachmEnts (continued) insert the instrument, turning it slightly to align the keyway.

lock the instrument in place by pushing the locking lever back. Pull lightly on the instrument to confirm that it is secure.

Electric Pen Drive System Reference Guide DePuy Synthes Power Tools

11

scrEW insErtion attachmEnts Inserting an instrument

Instruments 05.001.028

screw attachment, ao coupling

05.001.029

screw attachment, hex coupling

05.001.034

screw attachment, mini quick coupling

Pull back the collar of the attachment and insert the instrument, turning it slightly to align the keyway. release the collar of the attachment and pull lightly on the instrument to confirm that it is secure.

12

DePuy Synthes Power Tools

Electric Pen Drive System Reference Guide

K-WirE attachmEnt Inserting a K-wire

Instrument 05.001.037

K-Wire attachment

Press the tensioning lever and insert a Kirschner wire into the attachment. the tensioning lever can be rotated 300° for surgeon preference.

release the tensioning lever to grip the wire. the wire can now be inserted into the bone. Repositioning or removing a K-wire to reposition the wire in the attachment, press the tensioning lever and pull back the unit along the Kirschner wire. release the tensioning lever once the wire is repositioned.

Electric Pen Drive System Reference Guide DePuy Synthes Power Tools

13

sagittal saW attachmEnts Inserting a saw blade in Sagittal Saw Attachment

Instruments 05.001.039

sagittal saw attachment

05.001.183

sagittal saw attachment, in-line

05.001.182

sagittal saw attachment, 90°

05.001.074

handhold for tool change

Press the clamping button on the attachment. insert a sagittal saw blade into the saw blade coupling and move it into the desired position (variable in 45° increments). release the clamping button. Pull lightly on the saw blade to confirm that it is secure.

14

DePuy Synthes Power Tools

Electric Pen Drive System Reference Guide

rEciProcating saW attachmEnt Inserting a saw blade or rasp

Instruments 05.001.040

reciprocating saw attachment

05.001.074

handhold for tool change

turn the release ring on the attachment clockwise until it locks in place.

insert a saw blade or rasp into the coupling, turning it slightly to align the keyway. the instrument will automatically lock in place. Pull lightly on the instrument to confirm that it is secure.

Electric Pen Drive System Reference Guide DePuy Synthes Power Tools

15

oscillating saW attachmEnt Instruments 05.001.038

oscillating saw attachment

05.001.074

handhold for tool change

Pull back the collar of the attachment. insert a saw blade into the saw blade coupling and move it into the desired position. release the collar. Pull lightly on the saw blade to confirm that it is secure.

16

DePuy Synthes Power Tools

Electric Pen Drive System Reference Guide

Burring Speed Attachments DePuy Synthes Power Tools recommends using a new burr for each surgery, as used burrs may increase the risk of necrosis and increase the cutting time. All burrs are sold sterile. Burrs should only be used with the attachment for which they were intended, or with an attachment one size shorter than the burr. For example, a medium burr should only be used in a medium or a short attachment. Long burrs can be used in the long and medium attachments as well as the XL and XXL attachments. Use only DePuy Synthes Power Tools burrs. The use of other cutting tools voids the device warranty.

Instruments 05.001.045

Burr Attachment, short

05.001.046

Burr Attachment, medium

05.001.047

Burr Attachment, long

05.001.048

Burr Attachment, short, angled

05.001.049

Burr Attachment, medium, angled

05.001.050

Burr Attachment, long, angled

05.001.055*

Burr Attachment, XXL, angled

05.001.063*

Burr Attachment, XL, angled

05.001.074 Handhold for Tool Change

Electric Pen Drive System

Reference Guide

DePuy Synthes Power Tools   17

BUrring sPEEd attachmEnts (continued) attach the burring attachment to the drive Unit or insert it in the handhold for tool change. turn the release ring of the burring attachment to the UnlocK position.

18

DePuy Synthes Power Tools

Electric Pen Drive System Reference Guide

BUrring sPEEd attachmEnts (continued) insert the burr as far as possible, turning it slightly to align the keyway. the burr is fully inserted when the s, m, or l mark on the burr shank is no longer visible. turn the release ring of the attachment to the locK position and pull lightly on the instrument to confirm that it is secure.

correct and incorrect insertion of the burr.

correct

incorrect

Electric Pen Drive System Reference Guide DePuy Synthes Power Tools

19