Operation Manual and Parts List
11 Pages
Preview
Page 1
Table of Contents Safety information ...3 Important Information...3 Alert Signals...3 Introduction...4 General Usage...4 Principles of Operation ...4 Installation ...4 General Specifications ...5 Environmental Conditions ...5 Declaration of Conformity ...5 Operation ...6 Precautions and Limitations...6 Maintenance and Servicing ...7 General Cleaning Instructions ...7 Exploded View ...8 Replacement Parts Listing ...9 Ordering Procedures ...10 One Year Limited Warranty ...11
2
Safety Information Alert Signals
Warning Warnings alert you to a possibility of personal injury. Caution Cautions alert you to a possibility of damage to the equipment.
Note Notes alert you to pertinent facts and conditions.
Your Thermo Scientific Speci-Mix Test Tube Specimen Mixer has been designed with function, reliability, and safety in mind. It is your responsibility to install it in conformance with local electrical codes. For safe operation, please pay attention to the alert signals throughout the manual.
Important Information
This manual contains important operating and safety information. You must carefully read and understand the contents of this manual prior to the use of this equipment.
3
Introduction Note With a 240V/60 Hz power supply the speed is 20 rpm, with a 240V/50 Hz, 16.5 rpm.
The Speci-Mix Test Tube Specimen Mixer provides gentle but thorough mixing of in vitro diagnostic specimens. The specimens are placed in the grooves of the white silicone pad, which is mounted on the platform. The platform rocks at a constant speed to provide gentle and thorough mixing of test tube contents.
General Usage
Do not use this product for anything other than its intended usage.
Principles of Operation
A synchronous gear motor drives a cam and linkage assembly that is attached to the rocker plate, which rocks in a cyclic 48° maximum motion at 18 rpm.
Installation
Remove the Speci-Mix from the carton. Check electrical specifications and plug into a properly grounded receptacle.
4
Operation Place tubes in the grooves of the white silicone pad. Center tubes for balanced mixing. On the side without ridges, the reversible pad will accept tubes over 125mm in length. The side with ridges will accept tubes less than 125mm in length. Turn the switch to the “on” position to start the mixing.
Warning To avoid personal injury, do not use in the presence of flammable or combustible chemicals - fire or explosion may result. This device contains components that may ignite such materials.
Note If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impared.
6
Precautions and Limitations 1.
2.
Do not overload by weight. Loads over 1-1/4 pounds may cause jerky rocking action.
Wash white silicone pad with soap and water and rinse when needed to assure the friction-grip quality of the pad.
Maintenance and Servicing Warning To avoid electrical shock, always disconnect from power supply before maintenance and servicing. Refer servicing to qualified personnel.
1. 2. 3.
The drive motor and linkage assembly do not require lubrication. The drive motor is impedance protected. Jerky rocking action without a load indicates motor replacement is necessary.
Failure of the unit when plugged in and with the toggle switch in the “on” position indicates defective toggle switch, malfunctioning drive motor or disengaged linkage. Remove right end cap to observe.
General Cleaning Instructions
Wipe exterior surfaces with lightly dampened cloth containing mild soap solution.
7
Exploded View Note When ordering replacement parts, be sure to order by part number - not by key number.
3
8
6
5 7 2
M26120-33, M26120, M26125, series 1106 8
9
4
10
Replacement Parts Warning To avoid electrical shock, always disconnect from power supply before maintenance and servicing. Refer servicing to qualified personnel.
Model Type: M26100, Series 1107 Model Type: M26100, Series 1107 Product Name: Speci Mix Aliquot Mixer Key * 2 3 4 5 6
7
8 9
10
Part # (Qty) PT261X1 PT1106X4 CV710X1A PT1106X3 MTX34 MTX35 CR1105X1 CR1105X2
Description Silicone top tube holder End plate assembly End cover End plate assembly Motor (M26125) Motor (M26120) Cord set (M26125) Cord set (M26120-33)
LN261X1
Link
SWX135 SWX136 PT261X3B CUX4
Switch (M26125) Switch (M26120-33) Top rocker plate assembly Coupling
* Not shown on exploded view.
Model Type: M71000, Series 1106 Model Type: M71000, Series 1106 Product Name: 1/2 Size Speci Mix Aliquot Mixer Part # (Qty) PT532X2 PT1106X4 CV710X1A PT1106X3 MTX34 MTX35 CR1105X1 CR1105X2 CRM1855X1 SWX135 SWX136 PT532X1A CUX4 LN261X1
Description Silicone top tube holder End plate assembly End cover End plate assembly Motor (M71015) Motor (M71010 and -33) Cord set (M71015) Cord set (M71010 -33) Cord set (M71010-33CN) Switch (M71015) Switch (M71010-33) Top rocker plate assembly Coupling Link
9
800-943-2006 or 800-926-0505
North America: USA/Canada +1 866 984 3766 (866-9-THERMO) www.thermo.com Europe: Austria +43 1 801 40 0, Belgium +32 2 482 30 30, France +33 2 2803 2180, Germany national toll free 08001-536 376, Germany international +49 6184 90 6940, Italy +39 02 02 95059 434-254-375, Netherlands +31 76 571 4440, Nordic/Baltic countries +358 9 329 100, Russia/CIS +7 (812) 703 42 15, Spain/Portugal +34 93 223 09 18, Switzerland +41 44 454 12 12, UK/ Ireland +44 870 609 9203 Asia: China +86 21 6865 4588 or +86 10 8419 3588, India toll free 1800 22 8374, India +91 22 6716 2200, Japan +81 45 453 9220, Other Asian countries +852 2885 4613 Countries not listed: +49 6184 90 6940 or +33 2 2803 2180