Operation Manual
268 Pages
Preview
Page 1
No. 2B771-050EN*F
OPERATION MANUAL FOR DIAGNOSTIC ULTRASOUND SYSTEM
MODEL SSA-660A [FUNDAMENTALS] (2B771-050EN*F)
CAUTION: In the USA, federal law restricts this device to sale by or on the order of a physician.
IMPORTANT! Read and understand this manual before operating the equipment. After reading, keep this manual in an easily accessible place.
© TOSHIBA MEDICAL SYSTEMS CORPORATION 2011-2012 ALL RIGHTS RESERVED
Introduction This operation manual describes the operating procedures for the diagnostic ultrasound system SSA-660A. To ensure safe and correct operation of the system, carefully read and understand the manual before operating the system.
Trademarks Microsoft® Windows® 2000 is a trademark of Microsoft Corporation in the U.S.A and other countries. Xario, ApliPure, DYNAMIC FLOW, and IASSIST are trademarks of Toshiba Medical Systems Corporation. This manual may include trademarks or registered trademarks of other companies. Note that the trademark symbol "™" and the registered trademark symbol "®" are not used in this manual.
IMPORTANT! 1. No part of this manual may be copied or reprinted, in whole or in part, without prior written permission. 2. The contents of this manual are subject to change without prior notice and without legal obligation. 3. The contents of this manual are correct to the best of our knowledge. Please inform us of any ambiguous or erroneous descriptions, missing information, etc.
No. 2B771-050EN*F
Safety Precautions 1.
Meaning of Signal Words
In this operation manual, the signal words DANGER, WARNING, and CAUTION are used regarding safety and other important instructions. The signal words and their meanings are defined as follows. Please understand their meanings clearly before reading this manual.
Signal word
Meaning
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Indicates a potentially hazardous situation which, if not avoided, may result in property damage.
CAUTION
2.
Meaning of Safety Symbols Symbol
Description Type-B applied part *
Type B when Type-B applied part is connected. The PCG sensor and pulse sensor that can be connected to this system are Type-B applied parts.
Type-BF applied part *
Type BF when Type-BF applied part is connected. Reference signal cables that can be connected to this system are Type-BF applied parts.
"Attention" (Refer to the operation manual.)
No. 2B771-050EN*F S-1
3.
Safety Precautions
Please observe the following precautions to ensure EMC and the safety of the patient and the operator when using this system.
3.1 Safety precautions in the operation manual <<Fundamentals volume>> The following four precautions are related to EMC. •
WARNING No. 10 on page S-4
•
CAUTION No. 2 on page S-7
• CAUTION No. 1 on page S-17 • CAUTION No. 2 on page S-17
DANGER:
Do not use flammable gases such as anesthetics or flammable liquids such as ethanol near this product. Doing so may cause an explosion. This product is not intended for use with oxygen or in an oxygen enriched atmosphere.
WARNING: 1. Warnings concerning electric shock, fire, and burns (1) If an abnormal smell or noise, or smoke occurs, immediately turn the system breaker OFF and disconnect the plug from the power outlet. Continuing to use the system with such an abnormality may result in a fire etc. When using the system, ensure that there is enough space for access to the breaker. (2) To prevent fire or electric shock, observe the following instructions regarding the power cable and plug. • Do not forcibly bend the cable. • Do not modify the power cable or plug. • Do not damage the power cable or plug. • Do not pull the power cable to disconnect the plug from the outlet. • Be sure to connect the power plug to a two-pin (with dual earth terminal) outlet meeting the ratings indicated on the rating nameplate. If this type of outlet is not available, contact your TOSHIBA representative. (3) Do not allow this system or other equipment to come into contact with the patient. If this system or other equipment is defective, the patient may receive an electric shock. (4) Do not connect to the system transducers other than those specified by TOSHIBA, to prevent accidents such as fire. (5) Do not use a defective transducer.
No. 2B771-050EN*F S-2
WARNING:
(6) Do not remove the covers or panels of the system. (7) When in the patient environment, the operator must not touch any exposed connectors. In addition, if the system covers have been removed for some reason, the operator must be extremely careful not to touch any part where the voltage exceeds 25 VAC or 60 VDC and the patient at the same time. 2. Information concerning the terminal to which the potential equalization conductor is to be connected (
):
To use another medical device in combination with this system, an equipotential wire for connecting to an equipotential bus must be supplied. For more information, contact your TOSHIBA representative. *
Be sure to connect the potential-equalization lead wire before inserting the equipment power plug into the receptacle. Also, be sure to remove the equipment power plug from the receptacle before disconnecting the wire to avoid electrical shock.
3. Information concerning the functional earth terminal ( ): Use of the functional earth terminal as protective earth is not allowed. The system should be connected according to local requirements and should not conflict with IEC60601-1 requirements. 4. Connect the earth conductor only before turning ON the system. Disconnect the grounding cable only after turning OFF the system. Otherwise, electric shock may result. 5. Do not connect this system to outlets with the same circuit breakers and fuses that control current to devices such as lifesupport systems. If this system malfunctions and generates an overcurrent, or when there is an instantaneous current at power ON, the circuit breakers and fuses of the building’s supply circuit may be tripped. 6. A separate power outlet of the specified rating must be provided to supply power to the diagnostic ultrasound system. Refer to the "Specifications" subsection for the power requirements of the diagnostic ultrasound system. Do not connect the diagnostic ultrasound system to the same power outlet as another device. Doing so may cause the power circuit breaker of the facility to trip, the fuses to blow, or a fire or electric shock to occur. 7. Do not push the system from the side. If the system is pushed from the side, it may fall down and cause injury.
No. 2B771-050EN*F S-3
WARNING: 8. When the optional reference signal cable is used, the following measures are required. (1) To prevent electric shock, check the following items before operation. • There must be no abnormality of the reference signal cable. • The reference signal cable must be connected correctly. (2) Connect the reference signal cable to the system before attaching the ECG electrodes to the patient. After the electrodes are attached to the patient, be careful not to allow them to come into contact with ground or other electrically live parts. If the reference signal cable connector or an electrode comes into contact with ground or other electrically live parts, the patient may receive an electric shock. (3) Do not place the ECG electrodes in direct contact with the patient's heart. Cardiac arrest may occur. *
The ECG electrodes are of the BF type and are not designed to be placed in direct contact with the heart.
(4) To reduce the risk of electric shock or burns, use only the cable and patient leads supplied with the reference signal unit (UJUR-660A). (5) The ECG electrodes used should be commercially available products provided by the customer. 9. Before using equipment such as an electric scalpel, highfrequency therapy equipment, an electro stimulator, or a defibrillator, remove the ECG electrodes from the patient. In addition, do not allow ultrasound transducers, a PCG microphone, a respiratory sensor, or a pulse sensor to come into contact with the patient. The patient may be burned or receive an electric shock. 10. The use of transducers and cables other than those specified, with the exception of transducers and cables sold by Toshiba Medical Systems Corporation as replacement parts, may result in increased emissions or reduced system performance.
No. 2B771-050EN*F S-4
WARNING: 11. Cautions regarding the biopsy procedures (1) To perform biopsy procedures while observing ultrasound images, a thorough understanding of ultrasound diagnosis and adequate training in biopsy procedures are required. Biopsy procedures are safer when performed using image observation than when performed without images. However, 100% safety and reliability cannot be assured even when performing biopsy procedures using image observation. If biopsy procedures are performed without proper knowledge or training, they may be performed incorrectly and cause various patient side effects. (2) In the situations listed below, the biopsy needle may fail to reach the target. Incorrect biopsy may cause various patient side effects. • A biopsy procedure is performed without adequate skills. • A biopsy adapter other than that specified is used. • The biopsy adapter is mounted at an incorrect position. • A biopsy needle that is unsuitable for the purpose of the biopsy is used. • A biopsy needle that is unsuitable for the biopsy adapter is used. • The image is frozen but it goes unnoticed, and the biopsy procedure is continued. • The position of the biopsy needle end is misinterpreted on the image. (3) Before and after a biopsy procedure is performed, confirm that there are no abnormalities with the biopsy adapter. If an abnormal biopsy adapter is used, the patient may be injured. (4) During a biopsy procedure, the needle may deviate from the desired course due to the tissue characteristics or the type of needle. In particular, needles with small diameters may deviate to a greater degree. Always monitor the target region and the needle end while performing a biopsy procedure. (5) Sterilize the transducer and biopsy adapter before and after an ultrasound-guided biopsy procedure. Failure to do so may result in the transducer and adapter becoming a source of infection. (6) The needle mark displayed on the ultrasound image does not indicate the actual position of the biopsy needle. It should only be used as a reference. (7) Do not freeze the image when performing a biopsy procedure. Biopsy procedures may be performed incorrectly on frozen images.
No. 2B771-050EN*F S-5
WARNING:
(8) Confirm that the selected needle mark angle matches the angle indicated on the biopsy adapter to be used. (9) The biopsy target may shift due to unexpected patient motion when the biopsy needle is inserted, or else due to respiratory movement. Always monitor the target region and the needle tip while performing a biopsy procedure. 12. When a transducer is applied to a patient with a high body temperature, the rate of heat dissipation from the transducer may be lower than normal. Take care not to cause a burn during examination (especially during surgery or an intracavitary examination). If the surface temperature of the transducer becomes abnormally high, stop using the transducer and contact your service representative. 13. Prolonged and repeated use of keyboards can result in hand or arm nerve disorders in some individuals. Observe the local institution work safety/health regulations on keyboard use. 14. This system is provided with a lossy data compression function for images. Although this function helps reduce the size of stored images, it can cause image deterioration. The amount of compression, therefore, must be limited so that the image quality is maintained at a level which does not adversely affect image viewing. 15. For the safety precautions regarding the use of contrast medium etc. in CHI mode, refer to the operation manual, Application volume. 16. Prepare a backup system when an urgent examination is to be performed, for example during an operation or for an emergency case. If a severe problem should occur with the system, the normal operation of the system may not be recovered by turning the power OFF/ON and the examination may not be able to continue. 17. Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. 18. This device is contraindicated for ophthalmic use or any application that causes the acoustic beam to pass through the eye. 19. Do not use the controls, adjusters, or operating sections of the DVD/CD unit in a manner other than specified. Incorrect use may cause hazardous beams to be radiated.
No. 2B771-050EN*F S-6
CAUTION: 1. Precautions concerning clinical examination techniques (1) This operation manual is intended for users who are wellversed in the principles and basic techniques of ultrasound. (2) This system must be used only by medical personnel fully trained in clinical examination techniques. (3) This operation manual does not describe clinical examination techniques. Selection of the proper clinical examination technique must be based on specialized training and clinical experience. 2. Malfunctions due to radiowaves (1) This system may malfunction due to electromagnetic influence from electric scalpels, high-frequency therapy equipment, or other devices that generate high frequencies. (2) Use of radiowave-emitting devices in the proximity of this kind of medical electronic system may interfere with its operation. Do not bring or use devices which generate radio waves, such as cellular telephones, transceivers, and radio controlled toys, in the room where the system is installed. (3) If a user brings a device which generates radio waves near the system, they must be instructed to immediately turn OFF the device. This is necessary to ensure the proper operation of the system. 3. Precautions concerning installation and movement of the system (1) Be sure to install the system on a level floor and lock the casters. If this is not done, the system may move, injuring the patient. (2) When the system is moved over a sloped surface, it must be moved by two persons. Otherwise, the system may slide unexpectedly and cause a serious injury. (3) Do not sit on the system. The system may move, causing you to lose your balance and fall. (4) Do not place any objects on top of the monitor. They may fall, causing injury. (5) Confirm that movable sections such as the LCD monitor and operating panel are locked before moving the system. Otherwise, the movable sections may move unexpectedly and cause injury. (6) Confirm that the peripheral units are secured before moving the system. Otherwise, the peripheral units may fall and cause injury. (7) If the reference signal cable is connected, disconnect it before moving the system. Otherwise, the cable may get caught in the casters or someone may trip over the cable and injury may result.
No. 2B771-050EN*F S-7
CAUTION:
(8) When the system is moved over a step, be careful not to allow the system to fall. When holding the system at the bottom to help move it over a step, take special care to prevent hand injuries. 4. In normal diagnostic ultrasound mode, there is no danger of a lowtemperature burn; however, keeping the transducer on the same region of the patient may cause such a burn. 5. Do not rub the LCD surface with a hard material or apply strong pressure to the LCD surface. Doing so may cause scratches on the LCD surface or result in damage to the monitor. 6. Terminals and connectors on the system side panel (1) Only the specified device must be connected to the USB connector or other connectors. Otherwise, smoke or an electric shock may result. (2) Only equipment that conforms to the safety standards must be connected to the ETHERNET terminal on the side panel. Otherwise, smoke or an electric shock may result. (3) Turn OFF the system power before connecting or disconnecting the cable from the ETHERNET terminal. If the cable is connected or disconnected with the system power ON, the system may not operate properly. (4) When a HUB is used, turn ON the system power only after tuning ON the power to the HUB. 7. Physio panel (option) (1) Only medical equipment that conforms with the IEC60601-1 standards must be connected to DC IN and AUX. Otherwise, an electric shock may result. (2) When external signals are input to DC IN and AUX of the Physio panel, the signal level that can be input is restricted. Contact your TOSHIBA representative for details. 8. Main panel switch configuration (1) The switch configuration on the main panel of this system can be changed. The switch settings may therefore differ depending on the system. When pattern U is set, the functions of the switches may differ depending on the system even if the same labels are attached to the switches. Confirm the switch configuration of your system before use. In particular, confirm the locations of the OUTPUT, STORE, and FREEZE switches. For details, refer to subsection 3.2 "Main Panel".
No. 2B771-050EN*F S-8
CAUTION:
(2) The descriptions in this operation manual are based on the standard switch configuration. If the switch configuration has been changed, the differences between the current configuration and the standard configuration must be understood before use. 9. Back up the stored data (image data and exam history) periodically and delete unnecessary data. If there is a limited amount of free space on the hard disk, the time required to display the ultrasound image after the system power is turned ON increases. 10. Do not turn OFF the power supply of the system during printing, data saving, or invoking. Doing so may result in failure of saving or printing or damage to the data. In addition, doing so during access to media may damage the media. 11. Standby mode (1) Before setting the system to Standby mode, be sure to save or print the necessary data. Otherwise, the data will be lost. (2) Do not set the system to Standby mode during printing, data saving, or invoking. Doing so may cause an error in these processes. (3) In addition, if the system is set to Standby mode during access to media, the media may be damaged. Furthermore, when used the next time, the printer or DVD/CD drive will not operate correctly. 12. Precautions regarding patient information entry (1) Be sure to register and save the patient ID before starting an examination for a new patient. If measurement is performed for a new patient for whom the patient ID is not registered or saved, the measurement results and other data cannot be saved in the system. In addition, the data for the two patients are mixed together, which may result in incorrect diagnosis. (2) Confirm that the patient to be examined is the same as the patient ID. There is a possibility of recording images with incorrect patient IDs. (3) Enter the patient's height and weight correctly in the patient ID registration screen. If the entered height and weight are not correct, the BSA will be calculated incorrectly. (4) Enter the patient information including LMP and IVF correctly in the patient ID registration screen. Otherwise, the fetal growth data will be calculated incorrectly. (5) Do not enter a patient ID consisting of spaces only. Doing so will result in reading/writing of data to/from media and DICOM transfer to other systems being performed incorrectly.
No. 2B771-050EN*F S-9
CAUTION: 13. Cautions regarding the presets (1) When a new imaging preset is to be created, the Exam Type is displayed automatically as the imaging preset name in the dialog. Be sure to change it. Otherwise, the examination may not be started with the factory setting even when "Factory" is selected in Exam Type registration in the system preset setting menu (refer to subsection 10.7). (2) If a change has been made to the system presets, be sure to turn OFF/ON the system power. Otherwise, the change will not go into effect. 14. Position of the biopsy target on the image and the biopsy needle Even though the biopsy target and the biopsy needle are identified on the image, a biopsy may not always be successful due to dispersion of the ultrasound beam. This is especially relevant when a biopsy procedure is to be performed for a tubule or a very small region. To avoid biopsy failure, follow the instructions below. (1) Do not rely solely on the echo of the needle end on the image. Pay careful attention to the target, which should shift slightly when the biopsy needle comes into contact with it. (2) Perform biopsy only after confirming the size of the target and the likelihood of biopsy success. 15. Precautions regarding the measurements (1) For basic measurements, the measured data is lost when image freeze is released or the image mode is changed during measurement. (2) The measurement data is lost when the system is turned OFF. However, the measurement data saved for application measurements is not lost. (3) The basic measurement result is not displayed on the report. (4) On the application measurement result screen, some calculation results are displayed. To check all the measurement results (calculation results), perform checks on the report screen. (5) The results edited on the report screen are not reflected in the measurement results on the image display. (6) When measurement is to be performed in M-mode or Doppler mode, confirm that the entire screen has been refreshed after changing the mode or settings. Otherwise, measurement may not be performed correctly.
No. 2B771-050EN*F S-10
CAUTION: 16. Do not display or print the data imported from other devices in this system. Such data may not be able to be displayed or printed correctly. 17. Peripheral units (1) To prevent electric shock, do not connect the peripheral units (video printer, VCR, etc.) to an external outlet. Peripheral units should be connected to the service outlet of the system. For the connection procedures, contact your TOSHIBA representative. (2) Some printers cannot detect print errors. Use the actual printout to confirm whether the data is printed correctly. (3) Do not turn OFF the power to the printer during printing. This may result in system malfunction. (4) Do not turn the power to peripheral devices ON or OFF during the system startup or shutdown process. This may result in system malfunction. (5) When the system is in Standby mode, do not disconnect any peripheral unit or turn the power ON/OFF. A malfunction of the peripheral unit may result. (6) When printing is executed, do not turn the system power OFF before all the images are printed. The data in the print queue may be lost. (7) When the color printer is to be used for printing, make sure that its power is ON. If printing is executed when the printer power is OFF, a system malfunction may result. 18. When an attempt is made to archive images on media or transfer them with the DICOM protocol, the following dialog may be displayed. Sorry. DVD/CD and DICOM storage are not available now. Please store important images to hard disk. Please power off and then power on to make them available. In this case, archiving to media and DICOM transfer cannot be performed. Store the important images on the hard disk. If you wish to archive images on media or transfer them with the DICOM protocol immediately, reboot the system. 19. The free space on the hard disk is displayed at the bottom of the screen in the format "HDD: xx% Free". Data cannot be saved if the free space is insufficient. Ensure the required free space before saving the images.
No. 2B771-050EN*F S-11
CAUTION: 20. Frame missing error in recording with the Snapshot Clips function (1) If the system detects that 4 or more consecutive image frames are missing, the error message below is displayed and the images are not recorded. Release the freeze status and acquire the image again. "System busy. Failed in Storing the image." (2) If the system detects that less than 4 consecutive image frames are missing, the message below is displayed at the bottom of the monitor. In this case, the images are recorded. "System busy. Some frames were missing." 21. Acoustic power (1) The FDA allows ultrasound equipment to output acoustic power level TRACK3, which is higher than TRACK1, provided that MI/TI values are displayed on the system. This means that users have a higher degree of responsibility for safety than manufacturers. Against this background, users are required to understand the ultrasound bioeffects and their causes. (2) It is strictly required that acoustic output be set based on the ALARA (As Low As Reasonably Achievable) principle. However, not all examinations can be performed with an extremely low level of acoustic energy. Controlling the acoustic level at an extremely low level leads to low-quality images or insufficient Doppler signals, adversely affecting the reliability of the diagnosis. However, increasing the acoustic power more than necessary does not always contribute to an increase in quality of information required for diagnosis, rather increasing the risk of generating bioeffects. Users must take responsibility for the safety of patients and utilize ultrasound deliberately. Deliberate use of ultrasound means that output power of ultrasound must be selected based on ALARA. (3) Set the ultrasound output as low as possible when a fetus is to be exposed to ultrasound. (4) Note that there are switches on the operation panel, the pop up menu and the touch panel other than the ACOUSTIC POWER, the MI/TI value may change in a direction not intended for those switches. 22. If preventive maintenance is performed by the user, special care must be taken to ensure safety. 23. If any abnormality of the system is found as a result of inspection, stop using the system and contact your TOSHIBA representative for repair. 24. In no event shall TOSHIBA be liable for problems, damage, or loss caused by inspection performed by personnel other than TOSHIBA service personnel or those designated by TOSHIBA.
No. 2B771-050EN*F S-12
CAUTION: 25. This system uses Windows 2000 as the OS. Do not change the settings of the OS. 26. Problems that typically occur in personal computers may also occur in this system. Important data must be stored on external storage media. 27. Only software authorized by TOSHIBA should be installed in this system. Otherwise, system failure or malfunction may result. Contact your TOSHIBA representative for details. 28. The doctor's judgement should be used when using contrast medium. For the procedures for using contrast medium, contact the manufacturer of the contrast medium. 29. Refer to the operation manual Measurement volume and Application volume for precautions regarding the use of measurement functions, optional software, etc. 30. Before cleaning the system, be sure to disconnect the system power cable from the outlet of the facility. If the system has been defective, an electric shock may occur. 31. Do not spill or spray liquids such as water onto the system or peripheral units. If a liquid such as water enters the system or peripheral units, an electric shock may occur. 32. Clean the reference signal cable regularly. (1) Do not allow clips to wet. The ECG is not displayed correctly. (2) Do not soak the connector in the water. Wipe the connector with dry cloth only. The water may enter the connector inside, possibly resulting in failure. (3) Do not use solvents (such as paint thinner, benzine, or alcohol) for cleaning the reference signal cable. 33. Cleaning the LCD monitor (1) Do not hit or apply strong pressure to the LCD surface during cleaning. Doing so may damage the monitor. (2) Never use a stiff or hard cloth to clean the LCD monitor. Doing so may damage the monitor cover or LCD surface. (3) If stains on the LCD surface are difficult to remove, wipe it gently with a soft cloth slightly moistened with water. Detergents or chemical agents should not be used because they may damage the monitor.
No. 2B771-050EN*F S-13
CAUTION:
(4) Do not attempt to clean the LCD monitor with organic solvents such as benzine, paint thinner, and alcohol or abrasive cleaners. Such agents may damage the monitor cover or LCD surface. Also, do not use mild detergent to clean the LCD surface. (5) Do not allow liquid droplets to remain on the LCD surface. The droplets may cause small stains when they dry or may enter the LCD surface, possibly resulting in failure. 34. Cleaning the trackball (1) Be extremely careful when removing dial. (2) Do not touch the encoding rollers. If foreign matter has adhered to the encoding rollers, contact your Toshiba service representative. (3) Set the dial so that it is seated securely. If the ring is locked with the dial not seated securely, the palm switch may be damaged. 35. If there is any possibility of secondary infection, cover the entire system with a sterile cover. To obtain a sterile cover, contact your TOSHIBA representative. 36. Malicious software (1) If this system is connected to a network for which any of the following conditions is true, the system can be infected with malware (malicious software, such as a computer virus or worm, that harms computers). The user must establish security measures to prevent the system from being infected. • Security control is not established for the network. • There is a risk of malware invasion in the network. • System for which any of the following conditions is true is connected to the network. (a) The security of the system is not controlled by the user. (b) The system can be accessed by persons not authorized by the user. (c) The system is capable of wireless communication.
No. 2B771-050EN*F S-14
CAUTION:
(2) The following instructions must be observed in order to prevent this system from being infected with malware (malicious software, such as a computer virus or worm, that harms computers). If the system is infected with malware, the data stored in the system may be lost, tampered with, or accessed by unauthorized persons; the system may operate incorrectly; or the system may become a source of malware infection. • Do not connect this system to a network for which security control is not established. • Do not connect this system to the Internet. • When an external storage media (such as a CD or USB flash memory) is to be used, confirm in advance that the media is not infected with malware. • Do not perform any other actions that may result in infection. 37. When discarding any part of this system, follow all applicable local regulations. 38. When this system is used to examine an elderly patient or an infant, an attendant should be present as required. 39. The displayed reference signals should be used for reference only. They should not be used for diagnosis or monitoring. In patients with cardiac pacemakers, an implantable electro stimulator, or arrhythmia, the heart rate or other parameters may not be displayed correctly. 40. Confirm that the LCD monitor arm is locked before moving the system. Otherwise, the LCD monitor arm may move unexpectedly, resulting in personal injury. 41. Do not place your hand on the LCD monitor arm or under the LCD monitor when adjusting the monitor angle. There is a risk of hand injury. 42. DVD/CD unit (1) Do not use lens cleaner to clean the disk. Lens cleaner will damage the drive. (2) Do not place adhesive labels on the disk. They may cause read errors or scratches on the disk. (3) Do not eject the media by pressing the [Eject] button during writing to the media. The data on the media may be damaged.
No. 2B771-050EN*F S-15
CAUTION:
(4) A disk that has been purchased in a spindle package may have protective sponge material applied to its surface. If such sponge material enters the internal mechanism of this unit, a malfunction may result. Confirm that there are no traces of sponge material on the disk before loading it into the unit. (5) The tray slides out approximately 15 cm when it is ejected. Keep the area in front of the tray clear. If the tray hits an obstacle, the tray may be damaged. (6) Do not leave the tray open. Dust may enter the unit and cause a malfunction, or a person may hit the tray and be injured. Open the tray only when necessary. 43. Do not connect any device to the USB connector other than a USB flash memory for storing and reviewing image data. 44. Do not press two or more switches on the system simultaneously. System malfunction may result. 45. During the system startup or shutdown process (or in standby status), do not attempt to operate the system (for example, turning a peripheral device ON/OFF, placing media into or removing media from the drive, or pressing a switch on the system). System malfunction may result.
No. 2B771-050EN*F S-16
CAUTION:
1. Do not use this system in locations subject to intense electric or magnetic fields (near transformers, for example). In such locations, the monitor will be adversely affected. 2. Do not use this system near devices generating high frequencies (such as medical telemeters and cordless telephones). The system can malfunction or adversely affect such devices. 3. To prevent damage to the system, do not use it in: • • • • • • •
Locations where it may be exposed to direct sunlight Locations where it may be subject to sudden changes in temperature Locations that are dusty Locations where it may be subjected to vibrations Locations near heat generators Locations where the humidity may be high Locations where the air filter of the system is blocked by walls, etc. (a space at least 10 cm wide and 20 cm deep is required.)
4. Turn ON the system only after the power has been OFF for more than 15 seconds. If the system is turned ON immediately after being turned OFF, the system may malfunction. 5. The user can record ID registration and user registrations (with a function to permit user-specific items such as the hospital name to be registered). Be sure to back up such information on external storage media. Data stored in the system may be lost due to improper operation or an accident. 6. Move the system by the handle. If the user pushes or pulls other sections such as the panel, the system may be damaged. 7. Do not press or use force on the main panel. It may damage the system. 8. The service outlet on the main unit provides power to recommended external options only. (Refer to subsection 2.3 "Compatible Peripheral Devices".) Do not connect other devices or the power capacity may be exceeded, and the system may malfunction. 9. The cooling fan must be cleaned once every 1 year. If the cooling fan is clogged, the internal temperature will rise, shortening the service life of the system. For inspection and cleaning by service personnel, contact your TOSHIBA representative. 10. Deterioration of electrical and mechanical safety characteristics (such as generation of a leakage current or deformation/abrasion of mechanical parts) and of image sensitivity and resolution may occur over a period of time. A maintenance service contract is recommended to avoid accidents and erroneous diagnosis and to maintain system performance.
No. 2B771-050EN*F S-17
CAUTION: 11. Observe the following precautions before moving the system to prevent system malfunctions. (a) Turn the power OFF and then turn OFF the breaker on the power supply panel at the rear of the system. (b) Store the transducer in the transducer holder and hang the cable on the transducer cable hanger. (c) When moving the system, use the handle. Do not push delicate sections such as the panel. 12. Do not stop the moving system using the total lock function except in emergencies. The casters can be damaged and abnormal operation can result. 13. Before connecting or disconnecting a transducer, deselect the transducer or turn the power OFF. If a transducer is connected or disconnected with an image displayed, the system and/or the transducer may malfunction. 14. Do not connect or disconnect a transducer during the system startup or shutdown process. This may result in system malfunction. 15. When lowering the main panel, take care not to apply a load to the cable hook or transducer holder. The cable hook or transducer holder may be damaged. 16. If the power cannot be turned OFF by the normal procedure, press and hold down POWER for at least 5 seconds. If the power is still not turned OFF, turn OFF the breaker of the power supply panel at the rear of the system. These methods should not be used under normal conditions. They may damage the system. 17. If the power is not turned OFF by following the normal procedures, 2D mode images may not be displayed when the system power is turned ON again. This does not indicate system failure. Turn OFF the breaker on the power supply panel on the rear of the system, wait at least 15 seconds, and then turn ON the breaker again. When the STANDBY LED lights, turn ON the power switch. 18. When the message "Printing" is displayed at the bottom-left corner of the monitor, it indicates that the system is ready to output images to the printer. Check the printer output for completion of the actual printing. Note that if the next print operation is executed while "Printing" is displayed, the next image is not printed. Confirm that the message "Printing" is cleared before executing the print operation. 19. When you wish to change an application preset, confirm that the application preset is displayed on the screen. Only changes to the displayed application preset can be saved. 20. When the measurement data displayed on the report screen is edited, the original data is overwritten by the edited data. The original data is not saved.
No. 2B771-050EN*F S-18