Technical User Guide
24 Pages
Preview
Page 1
This page intentionally left blank
RIO® Technical User Guide
Table of Contents INTRODUCTION ...1 ROBOTIC ARM INTERACTIVE ORTHOPEDIC SYSTEM (RIO®) COMPONENTS...3 USER APPLICATION SOFTWARE...6 RIO® TECHNICAL INFORMATION ...7 PREVENTIVE MAINTENANCE ...16 SYSTEM DISPOSAL...17
i
RIO® Technical User Guide
Unless qualified by MAKO Surgical Corp., healthcare facility Biomedical Engineering departments should limit system repair/maintenance to electrical safety testing as outlined in the Preventive Maintenance section of this manual.
There are no user serviceable parts in the RIO®, refer to your MAKO authorized personnel for service.
ii
RIO® Technical User Guide
INTRODUCTION About This Manual This manual provides information regarding hardware components of the Robotic Arm Interactive Orthopedic System (RIO®) for use as a reference. Manufacturer Support / Feedback MAKO Surgical Corp. 2555 Davie Rd. Ft. Lauderdale, FL 33317 Corporate Office Phone (954) 927-2044 Corporate Office Fax (954) 927-0446 makosurgical.com Updates Routine servicing may occur on a monthly basis. This may include, but is not limited to, verification of proper operation, recalibration, or updates. Indications for Use: The RIO® is intended to assist the surgeon in providing software-defined spatial boundaries for orientation and reference information to anatomical structures during orthopedic procedures. The RIO® is indicated for use in surgical knee and hip procedures, in which the use of stereotactic surgery may be appropriate, and where reference to rigid anatomical bony structures can be identified relative to a CT based model of the anatomy. These procedures include unicondylar knee replacement and/or patellofemoral knee replacement and Total Hip Arthroplasty. Software Versions supported include PKA 2.5, and THA 2.0, 2.1.
1
RIO® Technical User Guide
Copyrights and Trademarks The content of this manual is protected under applicable copyright and trademark laws. You agree that you will not copy, distribute, republish, display, post, transmit or modify any content in this manual without MAKO’s prior permission. Any images displayed in this manual are the property of their respective copyright owners. Any reproduction, replication, modification or distribution of any art images in this manual is prohibited. The third-party trademarks in this manual are proprietary to their respective owners. These companies or their agents have granted MAKO the right to use their trademarks. Trademarks registered in the United States. Trademark registrations pending in other jurisdictions. RIO® is a registered trademark of MAKO Surgical Corp. MAKOplasty® is a registered trademark of MAKO Surgical Corp. RESTORIS® is a registered trademark of MAKO Surgical Corp. MicroAire® is a registered trademark of MicroAire Surgical Instruments LLC. Anspach® is a registered trademark of The Anspach Effort, Inc. Governing Law Any legal action or proceeding related to this manual or the information contained in it shall be brought exclusively in a court in Broward County, Florida, and shall be governed by the laws of the State of Florida, without regard to conflicts of laws principles. Manufacturer MAKO Surgical Corp. 2555 Davie Rd. Ft. Lauderdale, FL 33317 Responsibility Under the terms of the service contract, maintenance and repair of the Robotic Arm Interactive Orthopedic System (RIO®) is the responsibility of MAKO Surgical Corp.
2
RIO® Technical User Guide
ROBOTIC ARM INTERACTIVE ORTHOPEDIC SYSTEM (RIO®) COMPONENTS The main components of the Robotic Arm Interactive Orthopedic System (RIO®) are the Robotic Arm, Guidance Module, and Camera Stand. Other instrumentation and accessories are available for use with the system, but are not discussed in this manual. Robotic Arm The RIO® Robotic Arm facilitates controlled bone resection by applying stereotactic boundaries to a cutting burr. The upper portion of the arm articulates, allowing motion with six Degrees of Freedom (DOF). The lower base houses the computer and power components, cable panel, user panel, and positioning lever. A smaller fixed arm is attached to the base and supports a reference array.
Figure 1. Robotic Arm Interactive Orthopedic System (RIO®)
There are no user-serviceable parts on the Robotic Arm.
3
RIO® Technical User Guide
Guidance Module The Guidance Module acts as a computer workstation for the MAKOplasty® Sales Specialist, houses one of the two system computers, and coordinates input from the various system components.
Figure 2. Guidance Module
There are no user-serviceable parts on the Guidance Module.
4
RIO® Technical User Guide
Camera Stand The camera or position sensor is used to track the location of passive tools. The camera is mounted on a mobile stand and can be positioned for height, angle, and rotation by adjusting the auto balance arm or the stand. The camera stand also includes a surgeon monitor display.
Figure 3. Camera Stand
There are no user-serviceable parts on the Camera stand.
5
RIO® Technical User Guide
USER APPLICATION SOFTWARE The RIO® software provides functionality to: •
Import or acquire patient CT DICOM data
•
Display the patient data using 2-D and/or 3-D representations
•
Register points in the patient data sets to the patient using various tracked instruments and tools
•
Display locations of tracked instrumentation with respect to other tracked instrumentation, registered patient anatomy, or the RIO®
•
Communicate with the RIO® and with the tool tracking system
•
Manage the application pages and the screen layout
Robotic Arm Software A separate software application runs on the Robotic Arm and is transparent (not accessible to the user). Functionally this application can be divided into 3 basic categories. •
Error/Safety monitoring
•
RIO® hardware control
•
Peripheral connectivity
Reporting Problems Hardware There are no internal user-serviceable parts in the RIO®. Unless qualified by MAKO Surgical Corp, do not open any system panels. Problems experienced during preoperative, intra-operative, or post-operative use of the RIO® should be reported to MAKO Surgical Corp. Software Software error reports are logged through the software and collected by MAKO service personnel during preventive maintenance.
6
RIO® Technical User Guide
RIO® TECHNICAL INFORMATION MAKO Surgical Corp. makes available to MAKO-trained personnel circuit diagrams, component part lists, descriptions, calibration instructions, or other information which will assist the appropriate qualified technical personnel to repair parts of equipment designated by MAKO Surgical Corp. Table 1. RIO® Technical Information Guidance Module
Robotic Arm
Camera Stand
Physical Storage Dimensions (LxWxH)
31" x 27" x 63"
24" x 35" x 56"
42" x 27" x 79"
Operating Dimensions (LxWxH)
31" x 27" x 63"
35" x 49" x 56"
56" x 27" x 79"
Power Requirements
N/A
100 / 120 / 230 V, 1150 W, ~50/60 Hz
N/A
Weight
114 lbs (51.7 kg)
866 lbs (394 kg)
190 lbs (86.2 kg)
Footprint
27" x 31"
24" x 35"
27" x 31"
Environmental Humidity
20% to 80% (non-condensing)
Temperature
Operating: 10° to 32° Celsius
Barometric Pressure
Sea level 1060 hPa to max conditions (5600M) 500 hPa
7
Storage: -20° to +50° Celsius
RIO® Technical User Guide Table 1. RIO® Technical Information (continued)
EMC Information RF emissions CISPR11
Class A
ESD Contact / Air EN61000-4-2
Class A / Class B
Radiated RF EN61000-4-3
3 V/m
Fast Transients (EFT) IEC61000-4-4
+/- 2 kV for power supply lines; +/- 1 kV for input/output lines
Line surge immunity IEC61000-4-5
+/- 1 kV differential; +/- 2 kV common mode
Conducted RF IEC61000-4-6
3 Volts
Power frequency (60 Hz) magnetic field EN61000-4-8
3 A/m
Voltage dip immunity IEC61000-4-11
Operated on 5%, 5%, 40%, and 70% of AC main power for 250 cycles, 0.5 cycles, 5 cycles, and 25 cycles, respectively.
Regulatory Compliance
Safety approvals
TUV SUD NRTL certification to: UL 60601-1:2003 for the US CAN/CSA C22.2 No. 60601-1-08 for Canada EN 60601-1:2006 for EU
Applicable standards
UL 60601-1:2003 CAN/CSA C22.2 No. 60601-1-08 EN 60601-1:2006
Classifications Per IEC 60601-1, the RIO® has been classified as: •
Continuous Operation, according to mode of operation
•
Class I, according to type of protection against electric shock
•
Type B Applied Part, according to degree of protection against electric shock
•
IPX0 rating, according to degree of protection against the ingress of fluids
Explanation of Labels For an explanation of all labels attached to the RIO® system, see the RIO® System User Guide (PN 203857).
8
RIO® Technical User Guide
RIO® Cabling Table 2. RIO® Cabling Part Name
Part Number
Length of Cable
RIO® Guidance Module (external cable to RIO)
200996 or 206083 (orange)
25 ft
Camera stand (external cable to Guidance Module)
200996 or 206083 (purple)
25 ft
Anspach eMax2 Plus
110940
12 ft 7 in
RIO® arm power cable
202247 or 207010
20 ft
RIO® Foot Switch
110970 or 207138
12 ft
MicroAire® Cable
203030
13 ft
Electromagnetic Interference This device is tested to the requirements of IEC 60601-1-2 for electromagnetic compliance for Class A, Group 1 medical devices. It has been shown not to emit RF energy at a level that may interfere or affect surrounding equipment. It is also shown to not be susceptible to RF or Electrostatic discharge (ESD) to a level that interferes or affects its own operation. This is predicated on the fact that the installation and operation is done in accordance with all service and operator instructions. The RIO® has special precautions regarding EMC and must be installed and put into service according to the EMC information provided in this Technical User Manual and the accompanying appendices. Portable and mobile RF communications equipment can affect the RIO®.
9
RIO® Technical User Guide
Electromagnetic Emissions Table 3. Electromagnetic Emissions This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced technician for help.
The user should not modify or change this device without written approval from MAKO Surgical Corp. Modification could void authority to use this equipment.
The RIO® is intended for use in the electromagnetic environment specified below. The customer or the user of the RIO® should ensure that it is used in such an environment. Emissions Test
Compliance
Electromagnetic Environment Guidance
RF emissions CISPR11 (RE-E)
Group 1, Class A
The RIO® uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
RF emissions CISPR11 (RE-E)
Group 1, Class A
Harmonic emissions IEC 61000-3-2
Class A
Voltage fluctuations/flicker emissions Complies IEC 61000-3-3
The RIO® is suitable for use in all establishments other than domestic and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
10
RIO® Technical User Guide The RIO® should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary, the RIO® should be observed to verify normal operation in the configuration in which it will be used. Table 4. Electromagnetic Immunity The RIO® is intended for use in the electromagnetic environment specified below. The customer or the user of the RIO® should assure that it is used in such an environment Immunity Test
IEC 60601 Test Level
Compliance Levelb
Electromagnetic Environment Guidance
Electrostatic discharge EN 61000-4-2
+/- 6 kV contact +/- 8 kV air
+/- 6 kV contact +/- 8 kV air
Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
Electrical fast transient/burst IEC 61000-4-4
+/- 2 kV for power supply lines +/- 1 kV for input/ output lines
+/- 2 kV for power supply lines +/- 1 kV for input/ output lines
Mains power quality should be that of a typical commercial or hospital environment.
Surge IEC 61000-4-5
+/- 1 kV differential mode +/- 2 kV common mode
+/- 1 kV differential mode +/- 2 kV common mode
Mains power quality should be that of a typical commercial or hospital environment.
Voltage dips, short interruptions and voltage variations on power supply input linesa IEC 61000-4-11
• <5% UT (>95% dip in UT) for 0.5 cycle
• <5% UT (>95% dip in UT) for 0.5 cycle
Mains power quality should be that of a typical commercial or hospital • 40% UT (60% dip in • 40% UT (60% dip in environment. If the user of UT) for 5 cycles UT) for 5 cycles the RIO® requires continued • 70% UT (30% dip in • 70% UT (30% dip in operation during power mains interruptions, it is UT) for 25 cycles UT) for 25 cycles recommended that the RIO® • <5% UT (>95% dip • <5% UT (>95% dip be powered from an in UT) for 5 sec in UT) for 250 cycle uninterruptible power source.
11
RIO® Technical User Guide Table 4. Electromagnetic Immunity (continued) The RIO® is intended for use in the electromagnetic environment specified below. The customer or the user of the RIO® should assure that it is used in such an environment Immunity Test Power frequency (60 Hz) magnetic field IEC 61000-4-8
IEC 60601 Test Level 3 A/m
Compliance Levelb 3 A/m
Electromagnetic Environment Guidance Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.
(a) UT is the A.C. mains voltage prior to application of the test level. (b) EN 61000-4-2 Class B pass criteria specifies that the Unit Under Test (UUT) may experience a self-recovering temporary failure.
12
RIO® Technical User Guide Table 5. Guidance and MAKO Surgical’s Declaration – Electromagnetic immunity The RIO® is intended for use in the electromagnetic environment specified below. The customer or the user of the RIO® should assure that it is used in such an environment Immunity Test • Conducted RF IEC 61000-4-6 • Radiated RF EN 61000-4-3
IEC 60601 Test Level
Compliance Levelb
• 3 Vrms 150 kHz • 3 V RMS to 80 Hz • 3 V/M • 3 V/m 80 MHz to 2.5 GHz
Electromagnetic Environment Guidance Portable and mobile RF communications equipment should be used no closer to any part of the RIO®, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance 3.5 d = -------- P V1 3.5 d = -------E1
P 80 MHz to 800 MHz
7 d = -----E1
P 800 MHz to 2.5 GHz
d = recommended separation distance in meters (m). p = maximum output power rating of transmitter in watts (W) according to transmitter manufacturer. Field strengths from fixed RF transmitters, as determined by an electromagnetic site survery, should be less than compliance level in each frequency range. Interference may occur in vicinity of equipment marked with following symbol:
13
RIO® Technical User Guide
a Field strengths from fixed transmitters, such as base stations for radio (cellular/ cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the RIO® is used exceeds the applicable RF compliance level above, the RIO® should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the RIO®. b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
14
RIO® Technical User Guide
The RIO® is intended for use in the electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the RIO® can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the RIO® as recommended below, according to the maximum output power of the communications equipment. Table 6. Recommended separation distances between portable and mobile RF communications equipment and the RIO® Separation Distance Based on Transmitter Frequency (m)
Rated Maximum Output Power of Transmitter (W)
150 kHz to 80 MHz 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz Outside ISM In ISM Bands Bands
3.5 d = -------V1
P
12 d = -----V2
P
12 d = -----E1
P
23 d = -----E1
0.01
0.04
0.12
0.12
0.23
0.1
0.11
0.38
0.38
0.73
1
0.35
1.2
1.2
2.3
10
1.11
3.8
3.8
7.3
100
3.5
12
12
23
P
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
At 80 MHz and 800 MHz, the higher frequency range applies. These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
15
RIO® Technical User Guide
PREVENTIVE MAINTENANCE The RIO® requires preventive maintenance (PM) performed by authorized service personnel to make reliable and consistent measurements of essential operational parameters. The PM session also provides the standard maintenance activities necessary to keep the system at its optimum level of performance. Preventive Maintenance is to be performed by MAKO-qualified service personnel only.
Preventive Maintenance will be initiated by MAKO Surgical Corp and may include the following activities: •
inspecting the system cables and connectors
•
inspecting and testing tracked tools and accessories (e.g., end-effector, base tracker, end-effector array)
•
inspecting and cleaning the RIO® robotic arm system
•
inspecting all LED functions
•
testing RIO® robotic arm calibration, homing, brakes
•
inspecting the UPS system on the robotic arm
•
inspecting and testing the RIO® robotic arm platform with tools including tool clamps, guides, mounts for accuracy
•
inspecting the mechanical cables in the arm
•
inspecting motor assemblies (encoders, motor phasing, etc.)
Cleaning, disinfection and electrical safety testing are to be considered preventive maintenance activities that are performed by the healthcare facility biomedical engineering department.
16
RIO® Technical User Guide
SYSTEM DISPOSAL Contact MAKO Surgical Corp before disposing of any RIO® equipment.
To dispose of RIO® equipment, it is recommended that the following procedure be followed. This procedure helps ensure the safe disposal of the system.
Procedure 1. Power down the equipment. 2. Inspect the equipment for signs of biohazard contamination. 3. De-contaminate the equipment. 4. Contact MAKO Surgical Customer Service for additional information required for removal of the system application software (as specified in the software license agreement) and disposal of any potentially hazardous materials. 5. Disassemble the equipment and dispose of it with a qualified salvage and disposal specialist.
17