Ti- Max series Handpiece Operation Manual

Titanium High Speed Air Turbine Handpiece X500K/X600K/X700K X500KL/X600KL/X650KL/X700KL (For KaVo® MULTIflex® LUX) X500SL/X600SL/X700SL (For Sirona® Quick Coupling) X500WL/X600W/X600WL/X700WL (For W&H® RotoQuick®) X500BL/X600BL/X700BL (For Bien-Air® Unifix® L)

OM-T0263E 001

Intended to Use This handpiece is designed only for dental treatment use.

Caution · When operating the handpiece always consider the safety of the patient. · Do not attempt to disassemble the handpiece nor tamper with the mechanism. · Check for vibration, noise and overheating outside the patient’s mouth. If any abnormalities are found do not operate. Contact authorized dealer for service. · Should the handpiece runs abnormally, cease operation immediately and return the handpiece to an authorized dealer for repair. · Do not exceed the rotation speed shown in Specifications. · Depressing the push-button while handpiece bur is in rotation will result in OVERHEATING of the handpiece head. Special caution must be exercised during use to keep cheek tissue AWAY from the push-button of the handpiece. Contact with cheek tissue may cause the push-button to depress and injury to the patient may occur. · Do not allow any impact on to the handpiece. Do not drop the handpiece. · Always keep bur shanks clean. Dirt or debris in a chuck could cause poor bur concentricity or low chuck retention force. · Remove the bur or handpiece only after it has completely stopped rotating. · Do not use long surgical burs. Do not use burs longer than 26mm. · Do not wipe nor immerse the handpiece in acidic water or acidic solutions. · Perform periodical maintenance checks. · If the handpiece has not been used for a long period, check for noise, vibration, and overheating before use. · Refer to the coupling manual for connecting it to the handpiece hose.

1. Specifications Model X500KL/X500SL/X500WL/X500BL X500K X600KL/X650KL/X600SL/X600WL/X600BL X600K/X600W X700KL/X700SL/X700WL/X700BL X700K Head Type Miniature Standard Torque Rotation Speed 390,000 ~ 450,000min-1 380,000 ~ 440,000min-1 300,000 ~ 360,000min-1 Drive Air Pressure 0.25MPa (2.5kgf/cm2) ~0.3MPa (3.0kgf/cm2) Spray Type Quatro Spray Chuck Type Ultra Push ISO1797-1 Type3 ø1.59~1.60 Bur Size Short Shank Standard Shank Optics Glass Rod - Glass Rod - Glass Rod - Head Diameter ø10.3mm ø11.2mm ø13.2mm Head Height 11.7mm 13.6mm 13.6mm *KaVo® and MULTIflex® are registered trademarks of Kaltenbach & Voigt GmbH & Co., Germany. Sirona® is a registered trademark of Sirona Dental Systems GmbH, Germany. W&H® and Roto Quick® are registered trademarks of W&H Dentalwerk Bürmoos GmbH, Austria. Bien-Air® and Unifix® are registered trademarks of Bien-Air Dental S.A., Switzerland.

2. Connection / Disconnection the Handpiece First make sure the manufacture’s coupling is firmly attached to the handpiece tubing and the drive air pressure is correct. For detail, refer to the coupling manual.

Caution Check tightness at the connection between the coupling and the handpiece.

3. Insertion/Removal of the Bur 3-1 To Insert the Bur

3-2 To Remove the Bur

1

2

Press the Push Button

2

Insert the Bur until it is secure

Remove the Bur

1 Press the Push Button

Caution Test that the bur is secure by gently pulling and pushing the bur without depressing the Push Button.

4.

Cautions for Bur Usage

· Do not use non-standard burs. The ISO standard shank diameter is ø1.59 - ø1.60 mm. · Do not use bent, worn, damaged, or non-concentric burs. · Always use within the bur manufacturer's recommended allowable speed. · Always use clean burs. Uncleaned burs may allow debris to build up inside chuck, causing weak bur retention or premature chuck wear. · Insert the bur all the way into the chuck until it stops with the push-button fully depressed. · Do not use short shank burs in Standard or Torque head handpiece.